Specifications

8 - EN
Auxiliary functions
Auxiliary Function Selection Buttons
C
Selecttherequiredauxiliaryfunctions
beforestartingtheprogram.
C
Somecombinationscannotbeselected
together.(Ex.:Pre-wash)(Figure1-5a)and
QuickWash(Figure1-5b).
Auxiliary function selection
If an auxiliary function that should not be
selected together with a previously selected
function is chosen, the first selected function
will be cancelled and the last auxiliary function
selection will remain active.
(Ex.: If you want to select pre-wash first and
then quick wash, pre-wash will be cancelled
and quick wash will remain active.
Auxiliary function that is not compatible
with the program cannot be selected. (see,
“Program Selection Table”)
• Prewash
When you select this function (5a), the display
will indicate “1” symbol. A pre-wash is only
worthwhile for heavily soiled laundry. Without
pre-wash you save energy, water, detergent
and time. Pre-wash without detergent is
recommended for lace and curtains.
• Quick Wash
With this function (5b), the wash time is
shortened. The “2” symbol will light up on the
display. Use this function for smaller amounts
or slightly soiled laundries.
• Rinse Plus
This function (5c) allows your machine to
perform an extra rinsing in addition to the
rinsing cycles performed by your machine after
main washing cycle. Thus, the risk for sensitive
skins (babies, allergic skins and etc.) to be
effected by the minimal detergent remnants on
the laundry is reduced. “3” symbol will light up
on the display.
• Anti-Creasing
With this function (5d), drum movement will
be lessened to prevent creasing and spinning
speed is limited. In addition, washing is carried
out at a higher water level. The “4” symbol will
light up on the display.
C
Wheneveryouselectthisauxiliaryfunction,
loadyourmachinewithhalfofthe
maximumlaundryspecifiedintheprogram
table.
Time display
The display shows the time remaining for
the program to complete while a program is
running. Program duration may differ from the
values in the consumption table subject to the
changes in the water pressure, water hardness
and temperature, ambient temperature, type
and amount of laundry, auxiliary functions
selected, and changes in the supply voltage.
Time delay
With the “Time delay” function you can delay
the program start up to 24 hours. Setting can
be made in intervals of 30 minutes.
1. Press“Timedelaying”buttons“+”and“-”
tosetyourdesiredtimedelay.
2. Press“Start/Pause/Cancel”button.Then
thetimedelaystartstocountdown.
C
Morelaundrymaybeloadedortakenout
duringthetimedelayperiod.
Changing the delay time
If you want to change the time during the
countdown:
1. Press“Start/Pause/Cancel”button.
2. Press“Timedelaying”buttons“+”or“-”to
setthedesiredtimedelay.
3. Press“Start/Pause/Cancel”button.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program immediately:
1. Press“Start/Pause/Cancel”button.
2. Pres“TimeDelaying”“-”buttonto
decreasethetimedelay.Programduration
after30minutesshallbedisplayed.
3. Press“Start/Pause/Cancel”buttontostart
theprogram.
Starting the Program
1. Press“Start/Pause/Cancel”buttontostart
theprogram.
2. Thestartsymbol(Figure2-7j)which
indicatesthattheprogramhasstartedwill
lightup.
3. Thedoorlocksandthedoorlocked
symbol(Figure2-7i)willlightup.
4. TheSymboloftherelevantstep(prewash,
mainwash,rinse,softenerandspin)that
theprogramhasstartedfromwilllightup
(Figure2-7f).
C
Ifthemachineisnotspinning,the
programmaybeinrinseholdmodeorthe
automaticspincorrectionsystemhasbeen
activatedduetoanexcessiveunbalanced
distributionoflaundryinthemachine.
Changing the selections after the
program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
When the “Program selection” button is
brought to the appropriate position, rpm and
temperature data reappear.