Datasheet
Product specifi cations in this catalog are subject to change without notice.Request our product specifi cations before purchase and/or use. Please use our products based on the information contained in this catalog and product specifi cations.
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
(at 20
℃
, 120Hz)
(at 105
℃
)
(at 20
℃
after 2 minutes)
(at 20
℃
, 120Hz)
(at 100kHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
Items
-
55 to +105
℃
2.5 to 25Vdc
±20% (M)
Rated voltage×1.15 (Rated voltage 2.5 to 20Vdc,
25Vdc)
/ Rated voltage×1.00 (Rated voltage 23Vdc)
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105
℃
.
Appearance No significant damage
Capacitance change
ESR
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to the DC rated voltage at
60
℃
, 90 to 95% RH for 1,000 hours(F46 : 500 hours).
Appearance No significant damage
Capacitance change
ESR
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
Appearance No significant damage
Capacitance change
ESR
Leakage current
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
Characteristics
◆DIMENSIONS [mm]
A
15L
39
16
V
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105
℃
.
Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
Rated voltage range : 2.5 to 25V
dc, case size range : φ4×5.2L toφ10×12.2L
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
0.3max.
A
±
0.2
W
P
Note : L+0.1/-0.2 for F46
L
±
0.5 for HC0 and JC0
Size code
D55
E60
F46
F55
F60
H70
HC0
J80
JC0
φ
D
4
5
6.3
6.3
6.3
8
8
10
10
L
5.2
5.7
4.5
5.2
5.7
6.7
12.0
7.7
12.2
A
4.3
5.3
6.6
6.6
6.6
8.3
8.3
10.3
10.3
B
4.3
5.3
6.6
6.6
6.6
8.3
8.3
10.3
10.3
C
5.1
5.9
7.2
7.2
7.2
9.0
9.0
11.0
11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.0
1.4
1.9
1.9
1.9
3.1
3.1
4.5
4.5
●
Terminal Code : A
Supplement code
Size code
Capacitance tolerance code
Taping code
Terminal code
Series code
Category
A P X A A R A GM
1342 6 7 8 9 10 1312518171611 1514
Please refer to "Product code guide (conductive polymer type)"
Lower ESR
PXA
PXE
●
●
●
●
RoHS Compliant
◆SPECIFICATIONS
Z(
-
25℃)/Z(+20℃)
≦
1.15
Z(
-
55℃)/Z(+20℃)
≦
1.25
of the initial value
≦±20%
≦
150% of the initial specified value
≦
150% of the initial specified value
≦
The initial specified value
DF
(tanδ)
DF
(tanδ)
DF
(tanδ)
≦
150% of the initial specified value
≦
150% of the initial specified value
≦
The initial specified value
≦
150% of the initial specified value
≦
150% of the initial specified value
≦
The initial specified value
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
◆MARKING
φ
D
±
0.5
B
±
0.2
C±
0.2
L
±
0.3 (Note)
◆PART NUMBERING SYSTEM
Capacitance code (ex. 10μF:100,100μF:101)
Voltage code (ex. 6.3V:6R3,10V:100)
EX) 16V39
µ
F
●
Halogen Free
CAT. No. E1001L(1/2)
Surface Mount
Dissipation Factor
(tan
δ
)
≦
±
20% of the initial value
≦
±
20% of the initial value