Datasheet

Product specifi cations in this catalog are subject to change without notice.Request our product specifi cations before purchase and/or use. Please use our products based on the information contained in this catalog and product specifi cations.
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Standard, Downsized, 105℃
L' 15min. 4min.
φD'
φd
F±0.5
Vent
(except
φ5)
F±0.5
Sleeve (PET : Brown)
●Endurance with ripple current : 1,000 to 2,000 hours at 105℃
●
Solvent resistant type except 350 to 450Vdc
(see PRECAUTIONS AND GUIDELINES)
●RoHS Compliant
◆SPECIFICATIONS
(at 20℃, 120Hz)
(at 20℃)
(at 20℃, 120Hz)
(at 120Hz)
(at 20℃ after 1 minute)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Items
- 55 to +105℃(6.3 to 100Vdc) - 40 to +105℃(160 to 400Vdc) -25 to +105℃(450Vdc)
6.3 to 450Vdc
±20% (M)
6.3 to 100V
dc 160 to 450Vdc
I=0.03CV or 4
µ
A, whichever is greater. After 5minutesAfter 1minute
CV≦1,000 I=0.1CV+40 max. I=0.03CV+15 max.
CV
> 1,000 I=0.04CV+100 max. I=0.02CV+25 max.
Where, I : Max. leakage current (
µ
A), C : Nominal capacitance (
µ
F), V : Rated voltage (V)
Rated voltage (Vdc)
tanδ (Max.)
When nominal capacitance exceeds 1,000
µ
F, add 0.02 to the value above for each 1,000
µ
F increase.
Rated voltage (V
dc)
Z(
- 25℃)/Z(+20℃)
Z(
- 40℃)/Z(+20℃)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 1,000 hours (2,000 hours to meet the following two conditions
1): 160V
dc and larger, 2) :φ12.5 and larger) at 105℃.
Capacitance change ≦±20% of the initial value
D.F. (tanδ) ≦200% of the initial specified value
Leakage current ≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage 6.3 to 100V
cd
160 to 450Vdc
Capacitance change ≦±20% of the initial value ≦±20% of the initial value
≦200% of the initial specified value
D.F. (tanδ) ≦200% of the initial specified value
Leakage current ≦The initial specified value ≦500% of the initial specified value
Characteristics
6.3V
0.34
10V
0.24
16V
0.20
25V
0.16
35V
0.14
50V
0.12
63V
0.10
100V
0.08
450V
0.24
160 to 250V
0.20
350 to 400V
0.24
6.3V
5
12
10V
4
10
16V
3
8
25V
2
5
35V
2
4
50V
2
3
63V
2
3
100V
2
3
450V
6
-
160 to 250V
3
4
350 to 400V
6
6
Time
CV
◆DIMENSIONS [mm]
◆PART NUMBERING SYSTEM
5
0.5
2.0
φD
φd
F
φD'
L'
6.3
0.5
2.5
8
0.6
3.5
12.5
0.6
5.0
16
0.8
7.5
18
0.8
7.5
10
0.6
5.0
φD+0.5max
L+1.5max
(φ5 toφ10) (φ12.5 to φ18)
Gas escape end seal
KMG
Downsized
KMQ
●Terminal Code : E
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 1.0
µ
F:1R0,10
µ
F:100,100
µ
F:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,100V:101)
Series code
Category
EKM G A A A E A A A A A A A A NM
1342 6 7 8 9 10 1312518171611 1514
Please refer to "Product code guide (radial lead type)"
CAT. No. E1001L(1/3)