Cordless Telephone MILANO User's Manual
Composition and Function of the Base and Handset ANTENNA SPEAKER ANTENNA LCD VOLUME /DISPLAY MODIFY KEY /PROGRAM SELECT REDIAL/PAUSE POWER INDICATOR IN USE/RINING/ PAGING INDICATOR CHARGING INDICATOR TALK/END KEY PROGRAM SEARCH CALL TRANSFER TO MULTI-HANDSET PAGING KEY MUTE KEY/PROGRAM INTERRUPTION RECALL KEY MEMORY KEY POWER KEY BASE CHARGE CONTACT MICROPHONE BELT CLIP BUZZER POWER SOCKET TELLINE SOCKET BATTERY COVER HANDSET CHARGE CONTACT Manual Abb.
Table of Contents Table of Contents 1 Safety .......................................................................................... 1 2 Connection of the Base and the Handset ............................... 3 2.1 Connection of the Base ............................................................3 2.2 Turn on the Handset .................................................................4 3 Bringing the Phone into Service .............................................. 5 3.1 Charging the Handset ......
Safety 1 Safety Please read this manual before use. Precaution Before using the phone, please read the operating instruction carefully. Take special care to follow the safety suggestions listed below. 1. Power Source : The phone should be connected to power source of 230V AC/50Hz through only the provided AC/DC adapter (DC 9V output). 2. The handset should be put on the base unit correctly for optimal charging. 3. The AC/DC adapter does not have its own power switch.
Safety For Best Performance 1. The phone should be placed away from personal computer, television, radio and fax machine. 2. If noise is high in conversation at the handset, approach the handset to the base to lessen the noise. 3. The handset should be used at the "High" volume setting when receiver voice level is too low to hear. 4. The handset should be fully recharged on the base when the battery low indicator is displayed. 5.
Connection of the Base and the Handset 2 Connection of the Base and the Handset 2.1 Connection of the Base 1. Insert the DC power plug into power socket (DC 9V) in the back of the base and insert AC/DC adapter to power outlet of 230V AC/50Hz. (Use only provided AC/DC adapter) 2. Insert one end of the telephone line cord into the base and the other end into the telephone line(PSTN) socket on the wall. 3. Call distance will depend on the position of the base.
Connection of the Base and the Handset 2.2 Turn on the Handset 1. Please press the power on key " " or just place the handset on the cradle. Then handset number and voice volume level will be displayed on the LCD. : Voice Volume Low : Voice Volume High 2. Before using the phone, please charge the battery of the handset for about 10 hours. 3. After charging, use the phone through the operating procedure.
Bringing the Phone into Service 3 Bringing the Phone into Service 3.1 Charging the Handset 1. Put the handset on the cradle for charging. 2. Charge the battery of the handset for 10 hours before initial use, and do it, if the battery low indicator " " is displayed on the LCD. 3. The handset is always charged while on the cradle. Be sure to put the handset on the cradle after use, so that it can be charged. Abb. 3-1 Charging the handset 3.2 Handset Power on/off To Power On/Off 1.
Placing and Answering Call 4 Placing and Answering Call 4.1 Placing Call Placing Call Make handset and base power on. Dial Pre-Dial 1. Make handset and base power on. 2. Dial or Dial For correction 4.2 Answering Call Auto Answer Used when handset is in charging stage. Answer can be automatically made by lifting the handset without any keying. Any Key Answer Used when handset is placed separately from base or charger. Answer can be made by pressing any key of ringing handset.
Function of Program Search Key 5 Function of Program Search Key Functions you can control with Program Search Key are as follows. Program Interruption The program process can be interrupted by pressing key " programming or not keying within 15 seconds.
Function of Program Search Key Pause Auto-Insertion Function To store the dial number under PABX-System (Internal Key Phone System), please follow the procedure as below: Set the Internal key number (0~9, off) For example when PABX internal key no. is "0". After setting the Pause Auto-Insertion, the phone makes a spot delay automatically after "0" on the LCD, when you start dialing with "0". so, you do not need to push the pause key manually every time, when you make a call under PABX - system.
Function of Program Search Key Erasing or Changing the Stored Number Telephone No. Press the memory location no. Erasing or changing no. Max 20 digits Placing Call with the stored number in memory Notice: If you press key " " once, the firstly stored memory dial is displayed on the LCD. If you press the key two times, the secondly stored memory dial is displayed on the LCD. for Pre-Dialing ...
Function of Program Search Key Talk Time Display Outgoing Call: 5 seconds after dialing /Incoming Call : 1 second after pressing key " ". Registering the Handset In case of multi handset(max. 3 sets) Put the handy on the base unit as charging mode Enter no. of extra handy(from 1~3) on the base unit Then the registered handset no. will be displayed on the LCD with a beep sound. Notice: All the handsets is registered to " 0 " at production.
Wall mounting and Battery Replacement 6 Wall mounting and Battery Replacement 6.1 Installation Environment 1. Water and Moisture: Keep the phone away from water and moisture, for example, near a bathtub, washbowl, or the like. Damp basement should also be avoided. 2. Heat: The phone should be installed away from heat sources such as radiators and the like. It also should not be placed in rooms where the temperature is less than 0° C or higher than 55° C 6.2 Placement 1.
Wall mounting and Battery Replacement 3. Use the nail or screw for installation. 8 mm Abb. 6-2 screws’ height 6.3 Battery Replacement 1. 2. 3. 4. Remove the battery cover. Remove the battery. Install the new battery. Put the battery cover. Abb. 6-3 Battery cover Versionsnr.
Trouble Shooting Guide 7 Trouble Shooting Guide Tab. 1: Trouble shooting guide Problem 1. The phone does not work. Cause & Remedy The battery is needed to be charged. The AC/DC adapter is not plugged into power outlet. The connection of the phone is made improperly. You are too far from the base unit. Move closer to the base unit. Check, if the Handset and Base are turned on. 2. Sound flutters with fading. You are too far from the base unit. Move closer to the base unit. 3.
ACHTUNG! WICHTIGE GARANTIEUNTERLAGE BITTE UNBEDINGT AUFBEWAHREN ! Lieber Kunde, wir freuen uns, dass Sie sich für eine Qualitätsprodukt der Marke entschieden haben. Sollte sich an Ihrem Gerät wider Erwarten ein technisches Problem ergeben, beachten Sie bitte folgende Punkte: • • • • Die Garantiezeit für Ihr Gerät beträgt 6 Monate. Bewahren Sie unbedingt den Kaufbeleg und die Originalverpackung auf.