User's Manual
Table Of Contents
- Intended audience of this document
- How to get technical support
- Trademarks
- Revision history
- How to get started
- Contents
- 1 Safety-related information
- 2 Consignes de sécurité
- 3 Technical terms and graphical symbols
- 4 Termes techniques et symboles graphiques
- 5 Product Overview
- 6 Certifications
- 7 Main CPU Module interfaces
- 7.1 Main CPU Module connectors (vers: -11)
- 7.2 Main CPU Module connectors (vers: -21 and -31)
- 7.3 Main CPU Modules Interfaces
- 7.3.1 USB0 and USB1: USB 3.0 connectors specifications
- 7.3.2 DP: Mini DisplayPort specifications
- 7.3.3 ETH0, ETH1, ETH2: Gb Ethernet connectors specifications
- 7.3.4 PWR IN: Power IN connector specifications
- 7.3.5 Navigation system specifications
- 7.3.6 LTE cellular modem specifications
- 7.3.7 Wi-Fi and BT specifications (vers: -21 and -31 only)
- 7.3.8 MVB ESD+ (RX only or RX/TX) interface specifications (vers: -11 only)
- 7.3.9 Earth connection terminal specifications
- 7.4 Main CPU Module LED indicators
- 7.5 Main CPU Module Service Panel and Service Interfaces
- 8 BoltAIR 20-31 interfaces
- 9 BoltIO 20-31 interfaces
- 10 BoltSER 20-31 interfaces
- 11 Product installation and power supply
- 11.1 Introduction
- 11.2 How to install the product on a DIN Rail
- 11.3 How to remove the product from a DIN Rail
- 11.4 Mechanical specifications
- 11.5 How to supply power to the system
- 11.5.1 Power supply specifications
- 11.5.2 The Ignition Key (Key Signal)
- 11.5.3 Main CPU Module and Expansion Modules electrical interconnections
- 11.5.4 Power supply safety instructions
- 11.5.5 How to supply power and turn ON the product
- 11.5.6 How to turn OFF the system
- 11.5.7 How to trigger a hardware reset of the system
- 12 Eurotech Everyware IoT
- 13 Product maintenance
- Notes
BoltGATE 20-31 User's manual EN 6 Certifications
© 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy
Code: BTGATE-20-31_MAN_EN_1-6
Revision: 1-6 2022.07.28
39 / 98
6.6.2 Antennas list for FCC/ISED compliance
NOTICE
Within the US/Canada, use the antennas in compliance with the FCC/ISED requirements.
Aux États-Unis et au Canada, les antennes doivent être utilisées conformément aux
exigences de la FCC/ISED.
The BoltGATE 20-31 has been FCC/ISED certified with the following antennas:
Le BoltGATE 20-31 a été certifié FCC/ISED avec les antennes suivantes:
Configuration: SET A
Types
Types
Manufacturer and Model
Fabricant et Modèle
Bands (MHz)
Bandes (MHz)
Peak Gain (dBi)
Max. Gain (dBi)
VSWR
Wi-Fi/BT Linx Technologies ANT-DB1-RAF-RPS 2400 - 2483
5150 - 5825
2.5
4.6
<1.9
Cellular 2J Antennas 2JW0124-C868B 698 - 960
1710 - 2170
2500 - 2700
0.4
2.6
1.3
2.4
1.6
2.2
GNSS 2J Antennas 2J4301MPGF 1575.42 - 1606 28 1.4
Configuration: SET B
Types
Types
Manufacturer and Model
Fabricant et Modèle
Bands (MHz)
Bandes (MHz)
Peak Gain (dBi)
Max. Gain (dBi)
VSWR
Wi-Fi/BT 2J Antennas 2J4802P 2410 - 2490
4920 - 5925
5925 - 7125
3.5
1.7
1.5
2.3
1.5
1.7
Cellular 2J Antennas 2J6983MPa
617 - 960
1427 - 2690
3300 - 5000
5150 - 5925
Cable 1:
2.1
6.3
3.7
2.8
Cable 2:
1.6
6.3
5.1
4.4
Cable 1:
3.1
2.1
3.1
3.0
Cable 2:
3.1
2.1
2.9
2.3
GNSS 2J Antennas 2J4301MPGF 1575.42 - 1606 28 1.4