User's Manual
Table Of Contents
- Intended audience of this document
- How to get technical support
- Trademarks
- Revision history
- How to get started
- Contents
- 1 Safety-related information
- 2 Consignes de sécurité
- 3 Technical terms and graphical symbols
- 4 Termes techniques et symboles graphiques
- 5 Product Overview
- 6 Certifications
- 7 Main CPU Module interfaces
- 7.1 Main CPU Module connectors (vers: -11)
- 7.2 Main CPU Module connectors (vers: -21 and -31)
- 7.3 Main CPU Modules Interfaces
- 7.3.1 USB0 and USB1: USB 3.0 connectors specifications
- 7.3.2 DP: Mini DisplayPort specifications
- 7.3.3 ETH0, ETH1, ETH2: Gb Ethernet connectors specifications
- 7.3.4 PWR IN: Power IN connector specifications
- 7.3.5 Navigation system specifications
- 7.3.6 LTE cellular modem specifications
- 7.3.7 Wi-Fi and BT specifications (vers: -21 and -31 only)
- 7.3.8 MVB ESD+ (RX only or RX/TX) interface specifications (vers: -11 only)
- 7.3.9 Earth connection terminal specifications
- 7.4 Main CPU Module LED indicators
- 7.5 Main CPU Module Service Panel and Service Interfaces
- 8 BoltAIR 20-31 interfaces
- 9 BoltIO 20-31 interfaces
- 10 BoltSER 20-31 interfaces
- 11 Product installation and power supply
- 11.1 Introduction
- 11.2 How to install the product on a DIN Rail
- 11.3 How to remove the product from a DIN Rail
- 11.4 Mechanical specifications
- 11.5 How to supply power to the system
- 11.5.1 Power supply specifications
- 11.5.2 The Ignition Key (Key Signal)
- 11.5.3 Main CPU Module and Expansion Modules electrical interconnections
- 11.5.4 Power supply safety instructions
- 11.5.5 How to supply power and turn ON the product
- 11.5.6 How to turn OFF the system
- 11.5.7 How to trigger a hardware reset of the system
- 12 Eurotech Everyware IoT
- 13 Product maintenance
- Notes
BoltGATE 20-31 User's manual EN 9 BoltIO 20-31 interfaces
© 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy
Code: BTGATE-20-31_MAN_EN_1-6
Revision: 1-6 2022.07.28
73 / 98
9.1.3.5 I/O 2: 12x Digital Outputs
Connector Layout:
Connector Specifications:
l
Standard HD 15-Pin D-Sub (plug)
l
Gender: Male
Mating Connector Specifications:
l
Standard HD 15-Pin D-Sub (socket)
l
Gender: Female
Connector Pinout:
Pin # Signal Type Description
1 OUT1 O Isolated Digital Output 1
2 OUT2 O Isolated Digital Output 2
3 OUT3 O Isolated Digital Output 3
4 OUT4 O Isolated Digital Output 4
5 C4 O Common for Outputs 1 to 4
6 C5 O Common for Outputs 5 to 8
7 OUT5 O Isolated Digital Output 5
8 OUT6 O Isolated Digital Output 6
9 OUT7 O Isolated Digital Output 7
10 OUT8 O Isolated Digital Output 8
11 C6 O Common for Outputs 9 to 12
12 OUT9 O Isolated Digital Output 9
13 OUT10 O Isolated Digital Output 10
14 OUT11 O Isolated Digital Output 11
15 OUT12 O Isolated Digital Output 12
9.1.4 Earth connection terminal specifications
Always use this terminal to connect the product to an earth point in the installation.
Terminal Layout: Terminal Label: Terminal Parts:
Part # Description
1 M4 stud bolt (length = 6.8 mm)
2 M4 lock nut
3 M4 washer
NOTICE
The earthing conductor to be connected to this terminal must have a size of 1 mm
2
.