User's Manual
Table Of Contents
- Intended audience of this document
- How to get technical support
- Trademarks
- Revision history
- How to get started
- Contents
- 1 Safety-related information
- 2 Consignes de sécurité
- 3 Technical terms and graphical symbols
- 4 Termes techniques et symboles graphiques
- 5 Product Overview
- 6 Certifications
- 7 Main CPU Module interfaces
- 7.1 Main CPU Module connectors (vers: -11)
- 7.2 Main CPU Module connectors (vers: -21 and -31)
- 7.3 Main CPU Modules Interfaces
- 7.3.1 USB0 and USB1: USB 3.0 connectors specifications
- 7.3.2 DP: Mini DisplayPort specifications
- 7.3.3 ETH0, ETH1, ETH2: Gb Ethernet connectors specifications
- 7.3.4 PWR IN: Power IN connector specifications
- 7.3.5 Navigation system specifications
- 7.3.6 LTE cellular modem specifications
- 7.3.7 Wi-Fi and BT specifications (vers: -21 and -31 only)
- 7.3.8 MVB ESD+ (RX only or RX/TX) interface specifications (vers: -11 only)
- 7.3.9 Earth connection terminal specifications
- 7.4 Main CPU Module LED indicators
- 7.5 Main CPU Module Service Panel and Service Interfaces
- 8 BoltAIR 20-31 interfaces
- 9 BoltIO 20-31 interfaces
- 10 BoltSER 20-31 interfaces
- 11 Product installation and power supply
- 11.1 Introduction
- 11.2 How to install the product on a DIN Rail
- 11.3 How to remove the product from a DIN Rail
- 11.4 Mechanical specifications
- 11.5 How to supply power to the system
- 11.5.1 Power supply specifications
- 11.5.2 The Ignition Key (Key Signal)
- 11.5.3 Main CPU Module and Expansion Modules electrical interconnections
- 11.5.4 Power supply safety instructions
- 11.5.5 How to supply power and turn ON the product
- 11.5.6 How to turn OFF the system
- 11.5.7 How to trigger a hardware reset of the system
- 12 Eurotech Everyware IoT
- 13 Product maintenance
- Notes
11 Product installation and power supply BoltGATE 20-31 User's manual EN
11.5.4 Power supply safety instructions
WARNING
Risk of electric shock. Failure to supply power correctly could result in death or serious
injury, and could damage the equipment or other property.
Refer to "What to do before you supply power to the product" below.
11.5.4.1 What to do before you supply power to the product
Before you supply power to the product, obey the following safety instructions:
l
Make sure that you have understood any instructions for safety, installation, and for operation
l
Make sure that your hands are dry
l
Make sure that all the cables to use:
o
meet the product requirements and comply with the relevant standards and regulations
o
are in good condition
o
are placed with care
o
are not placed where they may be trampled or compressed
l
Make sure that all power-points and plugs:
o
are in good condition
o
are not overloaded
l
Make sure that the product has a proper grounding connection
l
Make sure that the power supply source meets the product requirements and complies with the
relevant standards and regulations
l
Make sure that the product installation is made correctly and in compliance with the relevant
standards and regulations
l
Make sure that you supply power only after the product installation is completed.
If you have questions about these instructions, refer to: https://www.eurotech.com/en/support.
NOTICE
The negative line of the used power supply source will be connected to ground.
11.5.5 How to supply power and turn ON the product
To supply power and turn ON the system, complete the following steps:
1. Setup a DC power source that:
o
Meets the system power requirements
o
Has the negative line connected to ground
o
Delivers minimum power of 30 W
2. Check the input voltage as close as possible to the PWR IN connectorr. This is to compensate for
any cable losses, caused by cable length and other cable characteristics
(continued on next page...)
88 / 98 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy
Code: BTGATE-20-31_MAN_EN_1-6
Revision: 1-6 2022.07.28