User's Manual

ManualsBrandsEUROTECH ManualsComputers & Accessories802.11a/b/g/n/ac + BT 4.1 M.2 2230 Type Card Series

Table Of Contents

Trademarks
Intended audience of this document
Revision history
How to get started
Contents
1 Safety instructions
- 1.1 Warning messages
  - 1.1.1 Warning messages for harm to persons
  - 1.1.2 Warning messages for damage to property
- 1.2 Warning: power supply safety
- 1.3 Caution: product's surfaces may become hot
- 1.4 Caution: wireless safety
2 Consignes de securite
- 2.1 Messages d’avertissement
  - 2.1.1 Messages d’avertissement relatifs au dommage aux personnes
  - 2.1.2 Messages d’avertissement relatifs aux dommages matériels
- 2.2 Avertissement: sécurité de l’alimentation électrique
- 2.3 Attention: les surfaces du produit peuvent devenir chaudes
- 2.4 Attention: sécurité sur la connectivité sans fil
3 How to receive technical assistance
- 3.1 How to ask for technical support
- 3.2 How to send a product for repair
4 Comment obtenir une assistance technique
- 4.1 Comment contacter le support technique
- 4.2 Comment retourner un produit en service après vente
5 Conventions used
- 5.1 Conventions for signal names
- 5.2 Conventions for signal types
6 Product overview
- 6.1 Product description
- 6.2 Product label
- 6.3 Intended use and not allowed uses of the product
  - 6.3.1 Intended use
  - 6.3.2 Not allowed uses
- 6.4 Technical specifications
7 Regulatory information
- 7.1 CE compliance
- 7.2 FCC/ISED compliance
- 7.3 Antennas List
- 7.4 RoHS 3 compliance
- 7.5 REACH compliance
8 Interfaces overview
- 8.1 Rear Side Interfaces overview
- 8.2 Front Side Interfaces overview
  - 8.2.1 Service Panel Interfaces
- 8.3 LED Indicators overview
9 Interfaces in detail
- 9.1 Wi-Fi and Bluetooth
  - 9.1.1 Wi-Fi specifications
  - 9.1.2 Antennas connectors specifications
- 9.2 Internal Cellular Modem
- 9.3 MicroSIM card receptacles
  - 9.3.1 How to insert / remove the MicroSIM card
- 9.4 GNSS
- 9.5 USB 0, USB 1, USB 2
- 9.6 ETH 0, ETH 1
  - 9.6.1 Ethernet specifications
  - 9.6.2 ETH 0 and ETH 1 connectors specifications
- 9.7 COM 0, COM 1
- 9.8 CAN 0, CAN 1
  - 9.8.1 CAN 0 and CAN 1 connector specifications
- 9.9 Earth connection terminal
- 9.10 Display Port
  - 9.10.1 Display Port connector specifications
- 9.11 Digital I/O and Analog IN
- 9.12 Audio connector
  - 9.12.1 Audio connector specifications
- 9.13 TTL Serial Console
  - 9.13.1 TTL Serial Console connector specifications
- 9.14 MicroSD card receptacle
  - 9.14.1 How to insert / remove the MicroSD card in the receptacle
- 9.15 RTC (Real Time Clock)
- 9.16 TPM
- 9.17 Watchdog
- 9.18 Accelerometer and Gyroscope
- 9.19 Programmable pushbutton
10 Eurotech Everyware IoT
- 10.1 Everyware Software Framework (ESF)
- 10.2 The ESF Web UI
- 10.3 The ESF Wires application
- 10.4 Everyware Cloud (EC)
- 10.5 For more information
11 Mechanical specifications and dimensions
- 11.1 Product mechanical specifications
- 11.2 Product mechanical dimensions
12 How to install the product
- 12.1 Respect the clearance space
13 Power supply. How to turn ON/OFF and reset the product
- 13.1 Power supply specifications
- 13.2 Power IN connector specifications
- 13.3 How to Supply Power to the Product and Turn it ON
  - 13.3.1 Note about the Vehicle Ignition Sense
- 13.4 How to turn OFF the product
- 13.5 How to reduce the power consumption of the product
- 13.6 How to hardware reset the product
14 How to maintain the product
- 14.1 How to safely remove the power supply
- 14.2 How to verify the installation of the product
- 14.3 How to clean the product
Notes

DynaGATE 20-30 User manual Rev. 0-7 9 Interfaces in detail

9.12 Audio connector

The DynaGATE 20-30 provides an audio connector in the Service Panel.

9.12.1 Audio connector specifications

Connector Layout:

Connector Specifications:

l Shrouded header

l Gender: Male

l Type: Pitch 1.25 mm; 10-pin

Mating Connector Specifications:

l Connector Housing

l Gender: Female

l Type: Pitch 1.25 mm; 10-pin

l Example:

Manufacturer: Molex

Part Number: 51021-1000

(or equivalent)

Connector Pinout:

Pin # Signal Type Description

1 OUT_L+ O Left Line PositiveOut

2 OUT_L- O Left Line Negative Out

3 GND P Ground

4 OUT_R+ O Right Line Positive Out

5 OUT_R- O Right Line Negative Out

6 MIC_IN_L+ I Left Microphone Positive In

7 MIC_IN_L- I Left Microphone Negative In

8 GND P Ground

9 MIC_IN_R+ I Right Microphone Positive In

10 MIC_IN_R- I Right Microphone Negative In

57 / 76