User's Manual

ManualsBrandsEUROTECH ManualsComputers & Accessories802.11a/b/g/n/ac + BT 4.1 M.2 2230 Type Card Series

Table Of Contents

Trademarks
Intended audience of this document
Revision history
How to get started
Contents
1 Safety instructions
- 1.1 Warning messages
  - 1.1.1 Warning messages for harm to persons
  - 1.1.2 Warning messages for damage to property
- 1.2 Warning: power supply safety
- 1.3 Caution: product's surfaces may become hot
- 1.4 Caution: wireless safety
2 Consignes de securite
- 2.1 Messages d’avertissement
  - 2.1.1 Messages d’avertissement relatifs au dommage aux personnes
  - 2.1.2 Messages d’avertissement relatifs aux dommages matériels
- 2.2 Avertissement: sécurité de l’alimentation électrique
- 2.3 Attention: les surfaces du produit peuvent devenir chaudes
- 2.4 Attention: sécurité sur la connectivité sans fil
3 How to receive technical assistance
- 3.1 How to ask for technical support
- 3.2 How to send a product for repair
4 Comment obtenir une assistance technique
- 4.1 Comment contacter le support technique
- 4.2 Comment retourner un produit en service après vente
5 Conventions used
- 5.1 Conventions for signal names
- 5.2 Conventions for signal types
6 Product overview
- 6.1 Product description
- 6.2 Product label
- 6.3 Intended use and not allowed uses of the product
  - 6.3.1 Intended use
  - 6.3.2 Not allowed uses
- 6.4 Technical specifications
7 Regulatory information
- 7.1 CE compliance
- 7.2 FCC/ISED compliance
- 7.3 Antennas List
- 7.4 RoHS 3 compliance
- 7.5 REACH compliance
8 Interfaces overview
- 8.1 Rear Side Interfaces overview
- 8.2 Front Side Interfaces overview
  - 8.2.1 Service Panel Interfaces
- 8.3 LED Indicators overview
9 Interfaces in detail
- 9.1 Wi-Fi and Bluetooth
  - 9.1.1 Wi-Fi specifications
  - 9.1.2 Antennas connectors specifications
- 9.2 Internal Cellular Modem
- 9.3 MicroSIM card receptacles
  - 9.3.1 How to insert / remove the MicroSIM card
- 9.4 GNSS
- 9.5 USB 0, USB 1, USB 2
- 9.6 ETH 0, ETH 1
  - 9.6.1 Ethernet specifications
  - 9.6.2 ETH 0 and ETH 1 connectors specifications
- 9.7 COM 0, COM 1
- 9.8 CAN 0, CAN 1
  - 9.8.1 CAN 0 and CAN 1 connector specifications
- 9.9 Earth connection terminal
- 9.10 Display Port
  - 9.10.1 Display Port connector specifications
- 9.11 Digital I/O and Analog IN
- 9.12 Audio connector
  - 9.12.1 Audio connector specifications
- 9.13 TTL Serial Console
  - 9.13.1 TTL Serial Console connector specifications
- 9.14 MicroSD card receptacle
  - 9.14.1 How to insert / remove the MicroSD card in the receptacle
- 9.15 RTC (Real Time Clock)
- 9.16 TPM
- 9.17 Watchdog
- 9.18 Accelerometer and Gyroscope
- 9.19 Programmable pushbutton
10 Eurotech Everyware IoT
- 10.1 Everyware Software Framework (ESF)
- 10.2 The ESF Web UI
- 10.3 The ESF Wires application
- 10.4 Everyware Cloud (EC)
- 10.5 For more information
11 Mechanical specifications and dimensions
- 11.1 Product mechanical specifications
- 11.2 Product mechanical dimensions
12 How to install the product
- 12.1 Respect the clearance space
13 Power supply. How to turn ON/OFF and reset the product
- 13.1 Power supply specifications
- 13.2 Power IN connector specifications
- 13.3 How to Supply Power to the Product and Turn it ON
  - 13.3.1 Note about the Vehicle Ignition Sense
- 13.4 How to turn OFF the product
- 13.5 How to reduce the power consumption of the product
- 13.6 How to hardware reset the product
14 How to maintain the product
- 14.1 How to safely remove the power supply
- 14.2 How to verify the installation of the product
- 14.3 How to clean the product
Notes

DynaGATE 20-30 User manual Rev. 0-7 9 Interfaces in detail

9.14 MicroSD card receptacle

The MicroSD card receptacle is placed on the top side of the circuit board in the Service Panel. The

receptacle allows you to insert a MicroSD card (up to 32 GB) for additional data storage.

9.14.1 How to insert / remove the MicroSD card in the receptacle

To insert the MicroSD card, complete the following steps:

1. Orient the MicroSD card with the contacts facing the circuit board

2. Push the MicroSD card and lock it in the receptacle

To remove the MicroSD card, complete the following steps:

1. Push the MicroSD card and release it from the receptacle

2. Pull out the MicroSD card from the receptacle

59 / 76