User's Manual
Table Of Contents
- Trademarks
- Intended audience of this document
- Revision history
- How to get started
- Contents
- 1 Safety instructions
- 2 Consignes de securite
- 3 How to receive technical assistance
- 4 Comment obtenir une assistance technique
- 5 Conventions used
- 6 Product overview
- 7 Regulatory information
- 7.1 CE compliance
- 7.2 FCC/ISED compliance
- 7.2.1 FCC marking
- 7.2.2 FCC compliance: Class B Digital Device
- 7.2.3 FCC restrictions on 5 GHz Wi-Fi usage
- 7.2.4 ISED Canada compliance
- 7.2.5 ISED Class B Digital Device Notice
- 7.2.6 Responsible parties: Canadian Representative contact information
- 7.2.7 RF Radiation Exposure Statement
- 7.2.8 Labeling information
- 7.3 Antennas List
- 7.4 RoHS 3 compliance
- 7.5 REACH compliance
- 8 Interfaces overview
- 9 Interfaces in detail
- 9.1 Wi-Fi and Bluetooth
- 9.2 Internal Cellular Modem
- 9.3 MicroSIM card receptacles
- 9.4 GNSS
- 9.5 USB 0, USB 1, USB 2
- 9.6 ETH 0, ETH 1
- 9.7 COM 0, COM 1
- 9.8 CAN 0, CAN 1
- 9.9 Earth connection terminal
- 9.10 Display Port
- 9.11 Digital I/O and Analog IN
- 9.12 Audio connector
- 9.13 TTL Serial Console
- 9.14 MicroSD card receptacle
- 9.15 RTC (Real Time Clock)
- 9.16 TPM
- 9.17 Watchdog
- 9.18 Accelerometer and Gyroscope
- 9.19 Programmable pushbutton
- 10 Eurotech Everyware IoT
- 11 Mechanical specifications and dimensions
- 12 How to install the product
- 13 Power supply. How to turn ON/OFF and reset the product
- 14 How to maintain the product
- Notes
DynaGATE 20-30 User manual Rev. 0-7 14 How to maintain the product
14 HOW TO MAINTAIN THE PRODUCT
Periodically inspect the product to verify its integrity and to ensure proper operation.
To maintain the product, complete the following steps:
1. Carefully read and understand the instructions contained in the section "Safety instructions" on
page9
2. Safely remove the power supply
3. Verify the installation of the product
4. Clean the product
14.1 How to safely remove the power supply
WARNING
ELECTRIC SHOCK HAZARD
Failure to remove power correctly may create an electric shock hazard, which could result in
personal injury or loss of life, and / or damage the equipment or other property.
To avoid injuries and safely remove power supply from the product, complete the following
steps:
1. Make sure your hands are dry
2. Turn OFF all the power supply sources
3. Disconnect all the cables
4. Make sure that all the circuits are discharged.
14.2 How to verify the installation of the product
To verify the installation of the product, complete the following steps:
1. Verify that the product is clean and not damaged
2. Verify that the LED indicators are visible and not damaged
3. Verify that all the locking parts (for example: screws, bolts, nuts) are correctly fastened
4. Verify that the product is installed correctly.
14.3 How to clean the product
To clean the product, complete the following steps:
1. Never use detergents, aerosol sprays, solvents or abrasive sponges
2. To remove dust from the case of the product, use a dry, lint-free, cloth
3. To remove the dirt, use water-based, non-flammable, cleaner products.
73 / 76