User manual DynaGATE 10-06 Automotive Multi-service IoT Edge Gateway - LTE Cat 1 and IP67 Rev.
Trademarks All trademarks, registered trademarks, logos, trade names, products names contained in this document are the property of their respective owners. Intended audience of this document This document is intended for system integrators: skilled persons with a thorough knowledge in linking together, physically or functionally, different computing systems and software applications to operate as a coordinated whole in compliance with the applicable regulations.
DynaGATE 10-06 User manual Rev. 0-8 Contents CONTENTS Trademarks Intended audience of this document Revision history Contents 1 Safety instructions 1.1 Warning messages 1.1.1 Warning messages for harm to persons 1.1.2 Warning messages for damage to property 1.2 Warning: power supply safety 1.3 Caution: wireless safety 1.4 Caution: product's surfaces may become hot 2 2 2 3 7 7 7 8 8 8 8 2 Consignes de securite 2.1 Messages d’avertissement 2.1.
Contents 7.2.5 ISED Class B Digital Device Notice 7.2.6 Canadian Representative contact information 7.2.7 RF Radiation Exposure Statement 7.2.8 Labeling Information 7.3 Antennas List 7.4 REACH compliance DynaGATE 10-06 User manual Rev. 0-8 30 30 30 31 31 32 8 Interfaces overview 8.1 Front Side Interfaces overview 8.2 LED Indicators overview 8.3 Service Panel and Service Interfaces 8.3.1 Service Panel Overview 8.3.2 Service Interfaces Overview 33 33 34 35 35 36 8 Rear Side Overview 8.3.
DynaGATE 10-06 User manual Rev. 0-8 12.2 How to install the product Contents 63 13 How to manage the product power supply 13.1 Power supply specifications 13.2 How to supply power and turn ON the product 13.3 How to turn OFF the product 13.4 How to reduce the power consumption of the product 13.5 How to trigger a hardware reset of the product 65 65 66 67 67 67 14 How to maintain the product 14.1 How to safely remove the power supply 14.2 How to verify the installation of the product 14.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 1 1 Safety instructions SAFETY INSTRUCTIONS IMPORTANT: Read carefully and understand the instructions and warnings contained in this document before installing / using the product. Keep this document for future reference. To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the instructions and warnings contained in this document.
1 Safety instructions 1.1.2 DynaGATE 10-06 User manual Rev. 0-8 Warning messages for damage to property To indicate potential risks of damage to the supported product (or to other property), the following message is used: NOTICE Sign (if necessary) 1.
DynaGATE 10-06 User manual Rev. 0-8 2 2 Consignes de securite CONSIGNES DE SECURITE IMPORTANT: Lire attentivement et bien respecter les instructions et les avertissements contenus dans ce document avant d'installer / d'utiliser le produit. Conserver ce document pour s'y référer à l'avenir. Pour éviter les risques de blessures, de choc électrique, d'incendie ou de détérioration du matériel, bien suivre les instructions et les avertissements contenus dans ce document.
2 Consignes de securite 2.1.2 DynaGATE 10-06 User manual Rev. 0-8 Messages d’avertissement relatifs aux dommages matériels Pour signaler les risques potentiels de détérioration du produit (ou des produits annexes), le message suivant est utilisé: AVIS Signal (si besoin) 2.
DynaGATE 10-06 User manual Rev. 0-8 2.4 2 Consignes de securite Attention: les surfaces du produit peuvent devenir chaudes Selon la température ambiante lors de l’utilisation, les surfaces du produit peuvent devenir brûlantes, engendrant un risque de brûlure. Laisser toujours les surfaces du produit refroidir avant de les toucher.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 3 How to receive technical assistance 3 HOW TO RECEIVE TECHNICAL ASSISTANCE 3.1 How to ask for technical support To ask for technical support, complete the following steps 1. Go to the Eurotech Global Support Centre: https://support.eurotech.com/ 2. Submit a support request 3. Wait for the reply from the Support Team with the information you required 3.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 4 Comment obtenir une assistance technique 4 COMMENT OBTENIR UNE ASSISTANCE TECHNIQUE 4.1 Comment contacter le support technique Pour demander un support technique, procéder comme suit: 1. Se connecter au Support Eurotech sur: https://support.eurotech.com/ 2. Envoyer une demande d’assistance 3. Attendre la réponse de l'équipe de support avec les informations requises 4.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 5 CONVENTIONS USED 5.1 Conventions for signal names 5.2 Convention Description GND Ground # Active low signal + Positive signal; Positive signal in differential pair - Negative signal; Negative signal in differential pair 3.3 3.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 6 Product overview 6 PRODUCT OVERVIEW 6.1 Product description The DynaGATE 10-06 is a Multi-service IoT Edge Gateway, designed to deliver LTE connectivity with 2G/3G fallback to automotive and lightly rugged applications. It is based on the NXP i.MX 6UltraLite Cortex-A7 processor family, with 512MB of RAM, 4GB of eMMC, and a user-accessible MicroSD and dual Micro-SIM slots.
6 Product overview 6.2 DynaGATE 10-06 User manual Rev. 0-8 Intended use and not allowed uses of the product The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). 6.2.
DynaGATE 10-06 User manual Rev. 0-8 6.3 6 Product overview Technical specifications The DynaGATE 10-06 is available in several -XY versions, for example: DynaGATE 10-06-36, where X=3 and Y=6. The following table lists the technical specifications of the DynaGATE 10-06 versions: Specifications Description according to DynaGATE 10-06-XY Version -31 -32 -33 -34 -35 -36 Processor CPU i.
6 Product overview DynaGATE 10-06 User manual Rev.
DynaGATE 10-06 User manual Rev. 0-8 6.4 6 Product overview Product labels The following labels are placed on the underside of the product: Ref # Label example Label type and content 1 Part Number and Serial Number Label This label contains the following: l Eurotech logo l Manufacturer address l Product number (xx = product version) l Serial number l Regulatory information and marks (according to product version.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 7 7 Regulatory information REGULATORY INFORMATION This section provides regulatory information for the DynaGATE 10-06 (hereafter referred to as "this "product"). Upon request, Eurotech can provide the product Declaration of Conformity. For details and more information contact the Eurotech Technical Support (see "How to receive technical assistance" on page 13). 7.
7 Regulatory information 7.1.5 DynaGATE 10-06 User manual Rev. 0-8 RoHS 3 compliance This product has been manufactured in compliance with the following Directives: l Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
DynaGATE 10-06 User manual Rev. 0-8 7.1.6.2 7 Regulatory information Class II product According to Commission Decision 2000/299/EC of 6 April 2000, establishing the initial classification of radio equipment and telecommunications terminal equipment and associated identifiers, the product falls within the scope of Class II.
7 Regulatory information 7.2 FCC/ISED Regulatory Notices 7.2.1 FCC marking DynaGATE 10-06 User manual Rev. 0-8 Some versions of this product are FCC marked (for more information see "Technical specifications" on page 21). They comply with the regulatory information reported in the following sections. Eurotech is not responsible for the use of the product together with equipment (for example: power supplies, personal computers, etc.
DynaGATE 10-06 User manual Rev. 0-8 l l l l 7.2.3 7.2.4 7 Regulatory information Réorienter ou déplacer l'antenne de réception Augmenter la distance entre le produit et le récepteur Brancher l'appareil sur une prise de courant différente de celle à laquelle le récepteur est raccordé Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide.
7 Regulatory information DynaGATE 10-06 User manual Rev. 0-8 brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Le présent émetteur radio a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci dessous et ayant un gain admissible maximal.
DynaGATE 10-06 User manual Rev. 0-8 7.2.8 7 Regulatory information Labeling Information The following information is stated on the product label(s): Les informations suivantes sont indiquées sur l'étiquette (les étiquettes) du produit: 7.
7 Regulatory information 7.4 DynaGATE 10-06 User manual Rev. 0-8 REACH compliance This product has been assessed to be compliant with the regulation (EC) No. 1907/2006 (REACH) (with the exceptions allowed by the EU Technical Committee). Eurotech has set in place a monitoring process to assess compliance to REACH regulation. For details and more information contact the Eurotech Technical Support (see "How to receive technical assistance" on page 13).
DynaGATE 10-06 User manual Rev. 0-8 8 Interfaces overview 8 INTERFACES OVERVIEW 8.1 Front Side Interfaces overview The Front Side Interfaces are as follows: Figure 8.1 - Front Side Interfaces layout Ref# Description 1 LED Indicators 2 Service Panel: includes the Service Interfaces Table 8.
8 Interfaces overview 8.2 DynaGATE 10-06 User manual Rev. 0-8 LED Indicators overview The LED Indicators are as follows: Figure 8.2 - LED Indicators layout Ref# Label Use Color 1 L1 General purpose. Controllable by user software Bi-color Green/Amber 2 L2 General purpose.
DynaGATE 10-06 User manual Rev. 0-8 8.3 Service Panel and Service Interfaces 8.3.1 Service Panel Overview 8.3.1.1 Ref# Description 1 Service Panel: includes the Service Interfaces 8 Interfaces overview How to Remove the Service Panel Cover NOTICE The IP grade is not maintained when the Service Panel cover is removed. Do not use the product for extended periods of time with the Service Panel cover removed, otherwise dust and other particulates may enter the system.
8 Interfaces overview 8.3.2 DynaGATE 10-06 User manual Rev. 0-8 Service Interfaces Overview The DynaGATE 10-06 has the following Service Interfaces: Figure 8.3 - Service Interfaces layout Ref# Description 1 3.3 V TTL Serial Console l Logic 1 (Hi): 2.0 to 3.3 V l Logic 0 (Low): 0 to 0.8 V 2 MicroSD Card Holder (push-push) 3 Host USB 2.0 OTG Port (for maintenance only) 4 Boot Modes Selection DIP-switch 5 Host USB 2.0 Port (for maintenance only. Ready to interface optional USB accessories, e.g.
DynaGATE 10-06 User manual Rev. 0-8 8.3.2.1 8 Interfaces overview TTL Serial console connector specifications Connector Layout: Connector Specifications: l Shrouded header l Gender: Male l Type: Pitch 1.25 mm; 3-pin Connector Pinout: Pin # Signal Type Description 1 GND P Ground 2 TX O Transmit Data 3 RX I Receive Data Mating Connector Specifications: l Connector Housing l Gender: Female l Type: Pitch 1.
8 Interfaces overview 8.3.2.4 DynaGATE 10-06 User manual Rev. 0-8 Boot Modes Selection DIP-switch The DynaGATE 10-06 has the following Boot Modes: l Main l Programmed To select the Boot Modes, set up the Boot Modes Selection DIP-switch according to the following table: Boot Mode DIP-switch set up Effect Main Switch #1: ON Switch #2: OFF Enables the boot sequence. By default it is as follows: 1. First boot device: USB(1) 2. Second boot device: eMMC(1). (1) A valid OS must be present in the device.
DynaGATE 10-06 User manual Rev. 0-8 8 8 Rear Side Overview REAR SIDE OVERVIEW The Rear Side is as follows: Figure 8.
8 Rear Side Overview 8.3.1 Connectors ETH1 and ETH2 Connector Layout: Connector Specifications: l Panel-mount; M12 series l Gender: Female l Type: D-Coded; 4-pin Mating Connector Specifications: l Cable-Mount; M12 series l Gender: Male l Type: D-Coded; 4-pin l Example of cable: Manufacturer: Conec Part Number: 43-00161 (or equivalent) 40 / 72 DynaGATE 10-06 User manual Rev.
DynaGATE 10-06 User manual Rev. 0-8 8.3.
8 Rear Side Overview 8.3.3 DynaGATE 10-06 User manual Rev. 0-8 Connectors A1, A4, A5 Connector Layout: Connector Pinout: Pin # Description 1 Female inner pin contact 2 Female connector body (outer thread) Connector Specifications: l SMA connector l Gender: Female Mating Connector Specifications: l SMA connector l Gender: Male 8.3.
DynaGATE 10-06 User manual Rev. 0-8 9 Features in detail 9 FEATURES IN DETAIL 9.1 Wi-Fi and Bluetooth (only for versions: -33 to -37) The DynaGATE 10-06 provides the following Wi-Fi / Bluetooth functionality: l 2.5 GHz Wi-Fi 802.11a,b,g,n / BLE 4.2 BLE Bluetooth l 5 GHz Wi-Fi 802.11a,b,g,n The internal circuitry allows for 2.5 GHz Wi-Fi and Bluetooth coexistence. The antennas connectors are (see also "Connectors A2 and A3" on page 42): l A2: 2.4 GHz Wi-Fi / Bluetooth l A3: 5 GHz Wi-Fi 9.1.
9 Features in detail 9.1.2 Bluetooth specifications l l l 9.1.3 Supports Bluetooth 4.
DynaGATE 10-06 User manual Rev. 0-8 9.
9 Features in detail 9.2.1.3 DynaGATE 10-06 User manual Rev. 0-8 Power Class 4G LTE LTE Power Class l Power Class 3 (23 dBm) 3G UMTS/HSDPA/HSUPA 2G GSM/GPRS/EDGE UMTS/HSDPA/HSUPA Power Class l Power Class 3 (24 dBm) GSM/GPRS (GMSK) Power Class l E-GSM band: Power Class 4 (33 dBm) l DCS band: Power Class 1 (30 dBm) EDGE (8-PSK) Power Class l E-GSM band: Power Class E2 (27 dBm) l DCS band: Power Class E2 (26 dBm) 9.2.1.4 Data Rate 4G LTE LTE category 1 l Download: up to 10.3 Mb/s l Upload: up to 5.
DynaGATE 10-06 User manual Rev. 0-8 9.2.1.7 9 Features in detail Second antenna requirements (for antenna diversity) Feature Description Impedance 50 Ohm Frequency range The required frequency range of the antenna connected depends on the operating bands of the used cellular module and the used mobile network. Bands See "Bands support" on page 45 Return Loss VSWR < 2:1 recommended VSWR < 3:1 acceptable Efficiency > -1.5 dB ( > 70% ) recommended > -3.
9 Features in detail 9.2.2 DynaGATE 10-06 User manual Rev. 0-8 1st and 2nd MicroSIM Card holders The DynaGATE 10-06 has two push-push MicroSIM card holders in the Service Panel, placed on the bottom side of the circuit board. If you use only one MicroSIM card: insert it in the 1st holder. NOTICE Turn OFF the SIM PIN before inserting the SIM card in the holder. The mobile connection will not work if the SIM PIN is ON. 9.2.2.
DynaGATE 10-06 User manual Rev. 0-8 9.3 9 Features in detail Internal GNSS (only for versions: -32 to -37) The DynaGATE 10-06 provides the following GNSS functionality: Dead Reckoning; 72 channels GPS/QZSS, GLONASS, BeiDou, Galileo. The antenna connector is A1 (see also "Connectors A1, A4, A5" on page 42). 9.3.1 Internal GNSS specifications Receiver type: l 72-channel engine l GPS/QZSS L1 C/A, GLONASS L10F l BeiDou B1I, Galileo E1B/C l SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN Nav.
9 Features in detail 9.4 DynaGATE 10-06 User manual Rev. 0-8 Digital I/Os The DynaGATE 10-06 has the following Digital I/Os: l 1x Insulated Digital Input l 1x Insulated Digital Output The Digital I/Os are available on the connector M1 (see also "Connector M1" on page 41). 9.4.1 Insulated Digital Inputs 9.4.1.1 Electrical specifications The table below shows the electrical specifications of the digital inputs: 9.4.1.
DynaGATE 10-06 User manual Rev. 0-8 9.4.2 Insulated Digital Outputs 9.4.2.1 Electrical specifications 9 Features in detail The table below shows the electrical specifications of the digital outputs: Characteristic Value Maximum Voltage 60 V Maximum Current 500 mA Output ON Resistance Typical: 0.85 Ohm Maximum: 2.50 Ohm Maximum Turn On time* 3 ms Maximum Turn Off time* 2 ms * Turn On/Turn Off time 9.4.2.
9 Features in detail 9.5 DynaGATE 10-06 User manual Rev. 0-8 COM ports The DynaGATE 10-06 has two COM ports: l 1 x RS-485 l 1 x RS-232 The COM ports are available on the connector M1 (see also "Connector M1" on page 41). 9.5.1 COM specifications Feature Maximum baud rate Description l l Notes 9.5.
DynaGATE 10-06 User manual Rev. 0-8 9.6 9 Features in detail CAN ports The DynaGATE 10-06 has two CAN ports: l CAN0 l CAN1 The CAN ports are available on the connector M1 (see also "Connector M1" on page 41). 9.6.1 9.6.2 CAN specifications Feature Description Compliance Compliant with the CAN Specification 2.
9 Features in detail 9.7 DynaGATE 10-06 User manual Rev. 0-8 Ethernet ports The DynaGATE 10-06 provides two 10/100 Mbps Ethernet ports: l ETH1 l ETH2. The Ethernet connectors are ETH1 and ETH2 (see also "Connectors ETH1 and ETH2" on page 40). 9.7.1 54 / 72 Ethernet specifications Feature Description Network Standard IEEE 802.3u 10/100-BaseTX. IEEE 802.3x full-duplex flow control. Speeds 10/100-BaseTX interfaces with MAC Notes The interfaces are noise and surge protected.
DynaGATE 10-06 User manual Rev. 0-8 9.8 9 Features in detail MicroSD card holder The DynaGATE 10-06 has one push-push MicroSD card holder in the Service Panel, placed on the top side of the circuit board. The MicroSD card holder allows you to insert a MicroSD card for additional data storage (up to 32 GB) 9.8.0.1 How to insert/ remove the MicroSD card To insert the MicroSD card, complete the following steps: 1.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 10 10 Eurotech Everyware IoT EUROTECH EVERYWARE IOT Eurotech Everyware IoT is a combination of hardware, firmware, operating systems, programming frameworks, and cloud platforms. It enables you to layer you added-value components on a reliable readyto-use infrastructure, dramatically accelerating the time to market of your IoT projects. 10.
10 Eurotech Everyware IoT 10.2 The ESF Web UI ESF provides a web-based user interface: ESF Web UI. The ESF Web UI provides several functions such as: l Monitor the gateway status l Manage the network configuration l Oversee the installed application(s) and services. The ESF Web UI is available on port 80 of the gateway IP. The default user is: admin The default password is: admin The following picture shows an example of the ESF Web UI: 58 / 72 DynaGATE 10-06 User manual Rev.
DynaGATE 10-06 User manual Rev. 0-8 10.3 10 Eurotech Everyware IoT The ESF Wires application ESF provides also a dataflow programming model: Wires. Wires simplifies the development of Edge Computing Applications leveraging reusable configurable components. In the dataflow programming model, the application logic is expressed as a directed graph (flow) where each node can have inputs, outputs and independent processing units.
10 Eurotech Everyware IoT 10.4 DynaGATE 10-06 User manual Rev. 0-8 Everyware Cloud (EC) Eurotech’s Everyware™ Cloud (EC) is an IoT Integration Platform that simplifies system and data management by connecting distributed devices over secure and reliable cloud services. Everyware Cloud allows you to connect, configure and manage devices through all the lifecycle, from deployment through maintenance to retirement.
DynaGATE 10-06 User manual Rev. 0-8 11 MECHANICAL SPECIFICATIONS 11.1 Product mechanical dimensions 11 Mechanical specifications The product electronics are housed in an aluminium alloy enclosure having the following dimensions: 165 (L) x 160 (W) x 62 (H); mm - Mounting Brackets included, Connectors not included. All dimensions are in millimetres.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 12 12 How to install the product HOW TO INSTALL THE PRODUCT The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). 12.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 13 13 How to manage the product power supply HOW TO MANAGE THE PRODUCT POWER SUPPLY NOTICE This product is not provided with any ON/OFF switch. The M1 connector is the disconnecting means from the power supply network. 13.1 Power supply specifications The DynaGATE 10-06 provides the Power IN interface within the M1 connector: l Pin 21 is the Ignition Key Input (KEY IN), a digital input that can be used to turn ON/OFF the DynaGATE 10-06.
13 How to manage the product power supply 13.2 DynaGATE 10-06 User manual Rev. 0-8 How to supply power and turn ON the product WARNING ELECTRIC SHOCK HAZARD Failure to supply power correctly or to follow all operating instructions correctly, may create an electric shock hazard, which could result in personal injury or loss of life, and / or damage the equipment or other property. To avoid injuries and safely supply power to the product, complete the following steps: 1.
DynaGATE 10-06 User manual Rev. 0-8 13 How to manage the product power supply 6. Connect Pin 21 (KEY IN) to a voltage level between 6 and 36 VDC ("Power IN +") NOTICE When you connect Pin 21 (KEY IN) to a voltage level between 6 to 36 VDC, keep it connected for at least 10 seconds; this allows for the booting procedure to be completed correctly. Otherwise, an immediate and unsafe power down will occur. 7. The DynaGATE 10-06 automatically turns ON and the LED L3 (Power status) turns ON. 13.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev. 0-8 14 14 How to maintain the product HOW TO MAINTAIN THE PRODUCT Periodically inspect the product to verify its integrity and to ensure proper operation. To maintain the product, complete the following steps: 1. Carefully read and understand the instructions contained in the section "Safety instructions" on page 7 2. Safely remove the power supply 3. Verify the installation of the product 4. Clean the product 14.
(This page has been intentionally left blank)
DynaGATE 10-06 User manual Rev.
EUROTECH.COM HEADQUARTERS Via Fratelli Solari, 3/a 33020 Amaro (UD) - Italy Tel: +39 0433.485.411 Fax: +39 0433.485.499 Email: welcome@eurotech.com Web: www.eurotech.com For your Eurotech local contact refer to: eurotech.com/contacts For the Eurotech Global Support Centre refer to: support.eurotech.com For the Eurotech Download Area refer to: eurotech.
