(8527+(50 '5,9(6 934 3URGXFW#0DQXDO #&RS\ULJKW#(XURWKHUP#'ULYHV#/LPLWHG#4<<< All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form or by any means to persons not employed by a Eurotherm group company without written permission from Eurotherm Drives Ltd. Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice, to make amendments or correct omissions.
:$55$17< Eurotherm Drives warrants the goods against defects in design, materials and workmanship for the period of 12 months from the date of delivery on the terms detailed in Eurotherm Drives Standard Conditions of Sale IA058393C. Eurotherm Drives reserves the right to change the content and product specification without notice. COPYRIGHT in this document is reserved to Eurotherm Drives Limited.
6$)(7<#,1)250$7,21 Please read this section BEFORE installing the equipment ,17(1'('#86(56 This Guide is to be made available to all persons who are required to install, configure, or service equipment described herein or any other associated operation. The information given is intended to highlight safety issues, and to enable the user to obtain maximum benefit from the equipment.
5,6.#$66(660(17 Under fault conditions, power loss, or other operating conditions not intended, the equipment may not operate as specified. In particular: • The motor speed may not be controlled. • The direction of rotation of the motor may not be controlled. • The motor may be energised. ,1#$//#6,78$7,216 THE USER should provide guarding and/or additional safety systems to prevent risk of injury and electric shock. &21752/#$1'#6,*1$/#:,5,1* All control and signal terminals are SELV, i.e.
&RQWHQWV 3DJH &KDSWHU#4#3URGXFW#2YHUYLHZ 404 'HVFULSWLRQ1111111111111111111111111111111111111111111111111111 404 (TXLSPHQW#6XSSOLHG 111111111111111111111111111111111111111 404 /('#'LVSOD\111111111111111111111111111111111111111111111111111 406 )XQFWLRQ#.
4#0#4##3URGXFW#2YHUYLHZ 3 52'8&7# 2 9(59,(: '(6&5,37,21 The 601 range of Frequency Inverters is designed for speed control of standard 3phase induction motors. The range covers motor power ratings from 0.37kW (1/2 hp) to 2.2kW (3 hp). The 601 features built in programming/operator controls and (optional) EMC compliant RFI filters. A pullout instruction guide provides quick reference for LED codes and terminal description.
3URGXFW#2YHUYLHZ#4#0#5 (8527+(50 '5,9(6 60I E M 7R#UHPRYH#7HUPLQDO#&RYHU#SUHVV#KHUH#DQG#SXOO#GRZQ '%54 '%55 &ORQLQJ#FRQQHFWLRQ +LQWHUQDO, (8527+(50 '5,9(6 60I /('#'LVSOD\ )XQFWLRQ .
4#0#6##3URGXFW#2YHUYLHZ /('#',63/$< Three seven segment LED displays provide drive programming, status and diagnostic values. Refer to the following tables for further information: • Table 5.1 for User Adjustable Parameters description (pages 5-1 and 5-2). • Table 5.2 for Drive Status description (page 5-5). • Table 5.3 for Diagnostics information (page 5-6). )81&7,21#.
3URGXFW#2YHUYLHZ#4#0#7 ,16758&7,21#38//287#*8,'( This panel gives the user sufficient information for basic operation of the product: • Translates the drive status information given in mnemonic form on the LED display (eg RDY = Ready; OC = Overcurrent). • Decodes the titles of the parameters (P1 to P15) and the diagnostics (D1 to D3) shown on the LED display (eg D1 = Frequency).
4#0#8##3URGXFW#2YHUYLHZ 32:(5#7(50,1$/#'(6&5,37,21 7HUPLQDO 'HVFULSWLRQ 5HIHUHQFH 7HUPLQDO /4 3RZHU#,QSXW /521 3RZHU#,QSXW /6 3RZHU#,QSXW 0428 0529 062: 3RZHU 2XWSXWV 5HIHUHQFH 7HUPLQDO )XQFWLRQ 5DQJH 5DQJH 5339#4#3KDVH 7339#6#3KDVH 6XSSO\#SURWHFWLYH#HDUWK#+3(,1##7KLV#WHUPLQDO#PXVW#EH FRQQHFWHG#WR#D#SURWHFWLYH#+HDUWK,#JURXQG#IRU #IRU SHUPDQHQW#HDUWKLQJ1 6;327939#$& 6LQJOH#DQG#WKUHH 55325739#$& “43(#ZLWK#UHVSHFW “43(#ZLWK#UHVSHFW SKDVH#OLYH WR#/521 WR#/5/#/6 FRQQHFWLRQ1 6LQJOH#SKDVH QHXWUDO#+RU#
7HFKQLFDO#'HWDLOV##5#0#4 7 (&+1,&$/# ' (7$,/6 (/(&75,&$/#63(&,),&$7,21 3$5$0(7(5 0D[#6XSSO\ &XUUHQW#4SK 6XSSO\#)XVH#5DWLQJ 43#[#6;#PP (DUWK#/HDNDJH &XUUHQW#+)LOWHUHG, 0D[#2XWSXW R &XUUHQW###73 & 0D[#2XWSXW R &XUUHQW###83 & +HDW#'LVVLSDWLRQ 5532573#9#“#43(##4#3KDVH#+,7271,- 81,76 316:N:2 318KS 3188N:2 31:8KS 31:8N:2 413KS 414N:2 418KS 418N:2 5KS 816 91< <18 4513 4813 $PSV#$& +506, 43 43 43 53 53 $PSV :18 :18 :18 :18 :18 P$ 515 613 713 818 :13 $PSV#$& 515 515 613 718 718
5#0#5##7HFKQLFDO#'HWDLOV (19,5210(17$/#63(&,),&$7,21 2SHUDWLQJ#7HPS 3#0#73°&#+VHH#7DEOH#514#IRU#FXUUHQW#UDWLQJ#DW#83R&, 6WRUDJH#7HPS 058#0#.88°& 6KLSSLQJ#7HPS 058#0#.:3°& &OLPDWLF#&RQGLWLRQV &ODVV#6.
7HFKQLFDO#'HWDLOV##5#0#6 Wall mounting clip can be easily pushed to allow different mounting configurations.
6#0#4##3URGXFW#&RGH 352'8&7#&2'( 601 /007 /230 /F /00 /UK Language * UK = English FR = French GR = German IT = Italian SP = Spanish US = American English Livery 00 = Eurotherm Standard Livery Internal RFI Filter 0 = No Filter F = Filter Fitted AC Supply Voltage +/- 10 % 230 = 220 / 240 V AC 1-Phase 400 = 380 / 460 V AC 3-Phase Power Ratings 003 = 0.37 kW 005 = 0.55 kW 007 = 0.75 kW 011 = 1.1 kW 015 = 1.5 kW 022 = 2.
(OHFWULFDO#,QVWDOODWLRQ##7#0#4 (/(&75,&$/#,167$//$7,21 Read the Safety Information at the front of the manual before proceeding. :,5,1*#*8,'(/,1(6#)25#(0& The 601 series has been designed to comply with the European Community Directive 89/336/EEC on EMC. In particular the 601 meets the given generic emission and immunity standards specified in table 2.2 when suitably cubicle mounted and when the internal RFI filter option is fitted.
7#0#5#(OHFWULFDO#,QVWDOODWLRQ &RQWURO#&DEOHV Control wiring should be segregated from all power wiring. To comply with the radiated emissions requirements of EN50081-1 the product must be inside a suitable control cubicle and the control cables must be screened outside of the cubicle. Connect the screen to earth at the 601 end only (see figure 4.3). Note the cubicle must provide 15dB attenuation to radiated emissions between 30 and 100MHz to meet the residential limits.
(OHFWULFDO#,QVWDOODWLRQ##7#0#6 by using two independent protective earth incoming supply conductors (figure 4.3). This is due to the high earth leakage current when using filters. The incoming mains supply should be protected by a suitable fuse or circuit breaker, as shown in table 2.1. Power cables should be specified to this table:- Current Rating Cable size Cable size < = 8 Amps 1 mm2 16 AWG < = 10 Amps 1.5 mm2 14 AWG < = 15 Amps 2.
7#0#7#(OHFWULFDO#,QVWDOODWLRQ The terminal used to control the speed of the motor depends on the setting of Parameter P13 Setpoint Select as shown in Table 4.
(OHFWULFDO#,QVWDOODWLRQ##7#0#8 7HUPLQDO#7LJKWHQLQJ#7RUTXH Terminals using automatic cage clamps are provided. Tightening torque is not applicable. ,QWHUQDO#2YHUORDG#3URWHFWLRQ These devices provide Class 10 motor overload protection. The maximum internal overload protection level (current limit) is 150% for 30 seconds. Refer page 5-1 for user current limit adjustment information.
7#0#9#(OHFWULFDO#,QVWDOODWLRQ NOTE: THE DYNAMIC BRAKING CIRCUIT IS DESIGNED TO COPE WITH SHORT TERM STOPPING OR BRAKING ONLY. IT IS NOT RATED FOR A CONTINUOUSLY OVERHAULING LOAD. All 601 units are supplied without braking resistors. The following paragraphs should be used as a guide to calculate the braking requirements of the system. %UDNH#5HVLVWRU#6HOHFWLRQ Brake resistor assemblies must be rated to absorb both peak braking power during deceleration and the average power over the complete cycle.
2SHUDWLQJ#'HVFULSWLRQ##8#0#4 23(5$7,1*#'(6&5,37,21 The 601 can be controlled in two different ways: 1. Remote Mode using the analogue and digital i/o on the control terminals. 2. Local Mode using the keypad. On the LED display, the User Adjustable Parameters are identified as P1 to P15 (see table 5.1), the Drive Status is shown using mnemonics (table 5.2), and the Diagnostics are identified as D1-D3 (table 5.3). The 601 has parameters factory defaults which are adequate for most applications.
8#0#5##2SHUDWLQJ#'HVFULSWLRQ 7LWOH 7UDQVODWLRQ 3å 'HVFULSWLRQ 5DQJH )DFWRU\ 'HIDXOW 580573#+] 83293+] 7KH#RXWSXW#IUHTXHQF\#DW +VHH#604, ZKLFK#PD[LPXP#YROWDJH#LV UHDFKHG1 Sä 30573#+] 43+] -RJ#6SHHG 7KH#VSHHG#DW#ZKLFK#WKH#934 ZLOO#UXQ#LI#&RQWURO#7HUPLQDO RU <#LV#KLJK +3UHVHW#5, 3ã 3UHVHW#6SHHG#6 7KH#VSHHG#DW#ZKLFK#WKH#934 30573#+] 58+] ZLOO#UXQ#ZKHQ#346# #5/ &RQWURO#7HUPLQDO#;#LV#ORZ DQG#&RQWURO#7HUPLQDO#<#LV KLJK 3ëì 3#0#<<< 3 3DVVZRUG $#SDVVZRUG#PD\#EH#VHW#WR SURKLELW#XQDXWKRULVHG DGMXVWPHQW#RI#3DUDPHWH
2SHUDWLQJ#'HVFULSWLRQ##8#0#6 39#9ROWDJH#%RRVW This is used to correctly flux the motor at low speeds. This allows the drive to produce greater starting torque for high friction loads. The VOLTAGE BOOST parameter increases the motor volts above the selected V/F characteristic at the lower end of the speed range.
8#0#7##2SHUDWLQJ#'HVFULSWLRQ 345#92)#6KDSH The V/F SHAPE parameter enables one of two voltage/frequency characteristics to be selected; OUTPUT VOLTS CONSTANT POWER RANGE 100% LINEAR QUADRATIC LAW FREQUENCY f B = BASE FREQUENCY fB LINEAR This gives a constant flux characteristic up to the BASE FREQUENCY. QUADRATIC This gives a quadratic flux characteristic up to the BASE FREQUENCY. This matches the load requirement for fan and most pump applications.
2SHUDWLQJ#'HVFULSWLRQ##8#0#8 '5,9(#67$786 7LWOH 'HVFULSWLRQ 3RVVLEOH#&DXVH 5($'<2+($/7+<#+1R#$ODUPV#3UHVHQW,1 2F 29(5&855(171 93423362563#0#934233:2563 93423362733#0#93423482733 93423442563#0#93423482563 93423552733 55$ 55$ 77$ 63$ Ramp Up 7LPH##WRR#VKRUW#IRU#LQHUWLD#RI ORDG#DQG2RU#SRZHU#UDWLQJ#RI#9341 Ramp Down 7LPH#WRR#VKRUW#IRU#LQHUWLD#RI ORDG#DQG2RU#SRZHU#UDWLQJ#RI#9341 $SSOLFDWLRQ#RI#VKRFN#RYHUORDG1 6KRUW#FLUFXLW#EHWZHHQ#PRWRU#SKDVHV1 6KRUW#FLUFXLW#IURP#PRWRU#SKDVH#WR#HDUWK1 0RWRU#FDEOHV#WRR#ORQJ
8#0#9##2SHUDWLQJ#'HVFULSWLRQ When a trip occurs a status message is flashed (de-coded by the above table 5.2). When the RUN command is removed the status message will stop flashing if the alarm has cleared. This will bring low control terminal 10 if Healthy/Unhealthy has been selected parameter P14 = 0. This places the product into a state where the RUN command can be re-applied and if the alarm does not reoccur the product will run normally.
(XURWKHUP#(0&#DQG#WKH#¶&(·#0DUN###9#0#4 (0&#$1'#7+(#¶&(·#0$5. START IS E.D. MODULE RELEVANT APPARATUS WITH INTRINSIC FUNCTION TO END USER (CEMEP VALIDITY FIELD 1) NO CEMEP VALIDITY FIELDS 2, 3 AND 4 YES OPTIONAL E.D. FILTERS AVAILABLE TO ASSIST USERS IN CONFORMANCE WITH THE EMC DIRECTIVE WILL THE E.D. PRODUCT BE INSTALLED ACCORDING TO THE INSTALLATION GUIDELINES NO EMC CHARACTERISTICS STATED IN MANUAL YES FIT THE SPECIFIED E.D. EMC FILTER THE E.D.
:#0#4##0DLQWHQDQFH#)#5HSDLU 0$,17(1$1&(#$1'#5(3$,5 0$,17(1$1&( Routine maintenance of the 601 comprises a periodic inspection to check for a buildup of any dust, or other obstructions, that may affect the ventilation of the unit. Obstructions should be removed and any dust must be cleared using dry air. 5(3$,5 The 601 contains no user serviceable component and MUST NOT BE REPAIRED by the user. If repair is necessary, return the unit to Eurotherm Drives.
(8527+(50 9,7(66( 9$5,$%/( 934 0DQXHO#GX#3URGXLW #&RS\ULJKW#(XURWKHUP#'ULYHV#/LPLWHG#4<<< All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form or by any means to persons not employed by a Eurotherm group company without written permission from Eurotherm Drives Ltd. Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice, to make amendments or correct omissions.
,66 4 5 6 02',),&$7,21 (&1 1R1 '$7( '5$:1 &+.
