User Manual

Knob Functions – Secondary Parameters
Out Lvl
Chop
“Chopping” Tremolo
LFO: Off, Triangle, Saw, Ramp,
Square, Random Sample/Hold
Auto-volume FX: Volume Swell,
Trigger extreme gating,
CW = increased sensitivity
Rear Panel
Power
9VDC center-negative
Mono/Stereo Switch
Left = Mono (TS plug)
Right = Stereo (TRS plug)
In Stereo, Tip is OUT1, Ring is OUT2
I/O Level Switch
Left - Guitar
Right - Line/Effects Loop
EXP
Connect Expression Pedal,
Auxiliary Switches or TRS MIDI
(See System Setup)
Mini USB
Software updates
& MIDI over USB
OUT1 & OUT2
In Mono, both outputs have
the same dry signal
Spd/Rise/Rel
Chop parameter control
LFO, SPD controls LFO Rate
SWL, Rise controls rise time
TRG, Rel controls release time
Predelay
Time before 1
st
Tap
1 sec max
Boost/Cut output level
Center for unity gain
Tone
Turn left for dark,
right for bright taps
IN
Standard TS (mono)
or TRS (stereo)
Slurm
Tap slurring/smearing/
modulation
Press button to toggle
Secondary/Primary parameters
Set Exp Pdl Jack Set Bypass Mode
Toggles On or Off for each setting
Factory Default = Buffered
System Setup
Set MIDI Channel
Set MIDI Clock
ON
1 2 3 4 5...
16
Set MIDI Channel: Click TAP Button
Default = Omni
BUFFER
RELAY
DSP+FX
KILL-DRY
PRESS
EXP (Default)
EXP + AUX
TRIPLE AUX
MIDI BOX
MIDI TRS
PRESS
Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch and button.
Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.
Catch Up ON/OFF
ON
Factory Default = Off
PRESS
PRESS PRESS
Load Preset
MIDI Messages
20
Mix
Length
Taps
Feedback
Spread
Taper
Chop
Spd/Rise/Rel
Out Lvl
Morphing from Heel to Toe
Enter Save Mode by pressing and holding the TAP
Button, then a MIDI program change message will save
a Preset to the Preset Slot of the given value 1-127.
21
22
23
24
25
26
27
28
Tone
Slurm
Predelay
29
30
31
CC
*Use a MIDI Converter Box
or a DIN to TRS or TRS cable
CCPRIMARY SECONDARY
Save Preset
Expression Pedal
NOTE: To use an Expression Pedal, the Exp
Pdl Jack must be set to either [EXP] or [EXP
+ AUX]. See System Setup to select.
An Expression Pedal can be used to change any
grouping of knob Parameters in one smooth
gesture. Programming an Expression Pedal is
easy. You simply need to set end points for Heel
& Toe. Here’s how:
1. Press Pedal fully Heel down.
2. Adjust any combination of the Parameter
control knobs.
3. Press Pedal fully Toe down.
4. Adjust any combination of the Parameter
control knobs.
5. Save it or lose it. See “Saving a Preset.”
Clear Expression Pedal Mappings
To clear the Expression Pedal mappings for the
knobs, hold the ACTIVE Footswitch and, while
holding, press the ACTIVE Button until the Preset
Ladder LEDs flash twice.
MIDI program change message loads the Preset
from the Preset Slot of the given value 1-127.
Note: The bottom two Ladder LEDs will be lit when
Presets 6–127 are selected via MIDI or Device Manager.
Receive/send using the USB Port or Exp Pdl Jack*.
CC 4: Expression Pedal
CC 9: TAP TEMPO
CC 14: ACTIVE/BYPASS (>=64 is Active)
Parameters: CC Messages Map
[EXP+AUX]
TIP = Expression Pedal
RING = TAP TEMPO
[TRIPLE AUX]
TIP = Increment Preset
RING = Decrement Preset
TIP + RING = Load Preset
Note: Times out after a few seconds
[MIDI BOX]
Receive and Send MIDI via a MIDI
Converter Box (Tip Active)
[MIDI TRS]
Receive MIDI directly with a DIN
to TRS or TRS cable.
MIDI Clock disables Tap switch and CC9
Factory Default = Off