User Manual

Set Exp Pdl Jack Set Bypass Mode
Toggles On or Off for each setting
Factory Default = Buffered
System Setup
Set MIDI Channel
Set MIDI Clock
ON
PRESS
Factory Default = Off
1 2 3 4 5...
16
PRESS
Set MIDI Channel: Click FREEZE Button
Default = Omni
BUFFER
RELAY
DSP+FX
KILL-DRY
PRESS
EXP (Default)
EXP + AUX
TRIPLE AUX
MIDI BOX
MIDI TRS
PRESS
Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch and button.
Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.
[EXP+AUX]
TIP = Expression Pedal
RING = TAP TEMPO
[TRIPLE AUX]
TIP = Increment Preset
RING = Decrement Preset
Tip + RING = Load Preset
Note: Times out after a few seconds
Catch Up ON/OFF
ON
PRESS
Factory Default = Off
[MIDI BOX]
Receive and Send MIDI via a MIDI
Converter Box (Tip Active)
[MIDI TRS]
Receive MIDI directly with a DIN
to TRS or TRS cable.
20
Mix
Feedback
Gravity
Size
Lo
Hi
Depth
Rate
Out Lvl
21
22
23
24
25
26
27
28
N/A
Delay
Q
29
30
31
CC CCPRIMARY SECONDARY
NOTE: To use an Expression Pedal, the Exp
Pdl Jack must be set to either [EXP] or [EXP
+ AUX]. See System Setup to select.
Load Preset
MIDI Messages
MIDI program change message loads the Preset
from the Preset Slot of the given value 1-127.
Note: The bottom two Ladder LEDs will be lit when
Presets 6–127 are selected via MIDI or Device Manager
Receive/send using the USB Port or Exp Pdl Jack*.
CC 4: Expression Pedal
CC 9: TAP TEMPO
CC 14: ACTIVE/BYPASS (>=64 is Active)
CC 15: FREEZE (>=64 is Freeze)
Parameters: CC Messages Map
Morphing from Heel to Toe
Enter Save Mode by pressing and holding the FREEZE
Button, then a MIDI program change message will save
a Preset to the Preset Slot of the given value 1-127.
*Use a MIDI Converter Box
or a DIN to TRS or TRS cable
An Expression Pedal can be used to change any
grouping of knob Parameters in one smooth
gesture. Programming Expression Pedal is easy.
You simply need to set end points for Heel &
Toe. Here’s how:
1. Press Pedal fully Heel down.
2. Adjust any combination of the Parameter
control knobs.
3. Press Pedal fully Toe down.
4. Adjust any or combination of the Parameter
control knobs.
5. Save it or lose it. See “Saving a Preset.”
Clear Expression Pedal Mappings
To clear the Expression Pedal mappings for the
knobs, hold the ACTIVE Footswitch and, while
holding, press the ACTIVE Button until the Preset
Ladder LEDs flash twice.
Save Preset
Expression Pedal
Knob Functions – Secondary Parameters
Delay
Predelay 0-2,000 msec
Rate
Rate of modulation
Mix
Dry/Wet Mix
Rear Panel
Power
9VDC center-negative
Mono/Stereo Switch
Left = Mono (TS plug)
Right = Stereo (TRS plug)
In Stereo, Tip is OUT1, Ring is OUT2
I/O Level Switch
Left - Guitar
Right - Line/Effects Loop
IN
Standard TS (mono)
or TRS (stereo)
Q
Resonance of Lo & Hi filters
Q has no effect if Lo/Hi
knobs are set to mid point
Depth
Depth/intensity
of modulation 
EXP
Connect Expression Pedal,
Auxiliary Switches or TRS MIDI
(See System Setup)
Mini USB
Software updates
& MIDI over USB
Out Lvl
Boost/Cut output level
Center for unity gain
Press button to toggle
Secondary/Primary parameters
OUT1 & OUT2
In Mono, both outputs
have the same dry signal