Item # 1002 782 617 Model # 9236060 INSTALLATION INSTRUCTION 18 IN. UNDERMOUNT RUNNER Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-305-1726 THANK YOU 924 395 700 HOMEDEPOT.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Is this the right drawer for my project? . . . . . . . . . . . . . . . . . 3 Pre-Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Planning Installation . . . . . . . . . . . . . . .
Installation Options 1 Is this the right drawer for my project? Please check the following points Drawer dimensions need to be met to fit slides Fits 18 in. deep drawers These slides can be installed in frameless and face frame cabinetry. Instructions for both options are provided in this manual The drawer side thickness must be 1/2 in. (13 mm) or 5/8 in.
Pre-Installation PLANNING INSTALLATION Ensure all parts listed in the Package Contents section are included and that you have the listed Tools and Materials Required on hand.
Dimensions Please review these diagrams and measure and mark your installation location before you begin the installation procedures. DRAWER DIMENSIONS Cabinet opening height Drawer height CABINETRY DIMENSIONS Inside cabinet width (ICW) 1-15/32" (37 mm) Drawer side thickness 1/2" (13 mm) or 5/8" (16 mm) Outside drawer width Inside drawer width 1-3/16" (30 mm) 13/16" (21 mm) Drawer depth: 21 in.
Face Frame Installation 1 Preparing the slides A /B Slide plastic connector from rear bracket into the notch on the left and right drawer slides (A and B) forward, as shown. 2 Face frame application Cabinet front edge 3/8“ (10 mm) Setback 3/32“ (2 mm) Front gap 1/16“ (1.5 mm) Face frame application with overlay decorative front Minimum/maximum cabinet depth (see below) Inset application increases minimum cabinet depth by thickness of decorative front.
Face Frame Installation 3 Metal rear attachment set (screw-on) Set contains 2 metal rear mount rackets and 2 plastic connectors Non-handed, two-piece design For up to 50 mm (1 15/16") depth adjustment and ± 1,5 mm (1/16“) side adjustment Additional adjustment via oblong holes Installation recommended with min.
Frameless Installation 1 Frameless application Cabinet front edge 1 7/16“ (37 mm) Min. 5/8“ (16 mm) 3/8“ (10 mm) Setback 3/32“ (2 mm) Front gap 1/16“ (1.5 mm) Frameless application with overlay decorative front Minimum cabinet depth (see below) Inset application increases minimum cabinet depth by thickness of decorative front.
Drawer Installation and Removal 1 Installing the drawer catches Install each drawer catch (C) into the two front corners of the drawer using #6 x 3/4 in. screws (H) or #6 x 1 in. screws (I). If you need to install the screws at an angle, do not angle the screws more than 30°. If your door subfront is 1/2 in. (13 mm) use the optional spaces (D).
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM Retain this manual for future use.
