FAQ

ManualsBrandsEverbilt ManualsPlumbing Product1/2 HP Shallow Well Jet Pump with 6 gal. Tank

Where Used

Typical Application

Pressure Ranges:

Typical Installations

Jet pumps turn on and off by a device called the pressure switch (included

with all jet pumps). The pressure range indicates when the pump will turn

on and off.

Ejector kits are required for proper use of the Deep Well (convertible) jet

pump. Without ejector kits, the pump would only move water – it would not

build enough pressure to turn off.

NOTICE: When replacing an existing pump, the old ejector kit located in

the well must be removed. Install the new ejector kit included with the

pump.

Deep Well Jet Pumps are positioned above ground and can pump from 25'

to 70' depth to water.

Mainly used for household water supply from a well, driven point, or open

water source. Pumps should be used with Standard or pre-charged

pressure tank.The larger the tank, the less the pump will turn on and off.

Jet Pumps

One pipe between water source and pump indicates a Shallow Well

pump, two pipes Deep Well pump.

How can I determine which style pump

I am replacing?

The pump can be installed in a basement, utility room or crawl space, at

the well, or between the well and the house. If installed outside, it should

be protected by a pump house with heat, and not exposed to sun or

moisture.

Frequently Asked Question

Deep Well Jet Pumps

Page 2

For Professional Technical Support call 1-844-241-5521

What additional items do I need?

Will the pumps operate regardless

of the voltage – 115 or 230?

The pump is factory pre-wired for 230 volts but can be changed to

operate on 115 volts (see owner’s manual).

When replacing an existing pump, look on the existing pumps

identification label for voltage information.

Where is the ejector kit located on a

Deep Well Jet Pump?

The ejector kit is not mounted on the pump for a deep well application.

The ejector is actually located in the well below the water level.

For Professional Technical Support call 1-844-241-5521

10 ft Min.

5 ft Min.

Tank

70 ft Max.

Foot valve

Ejector

(included)

Nipple

Pipe

Well seal

Elbow

Priming tee

and plug

Flexible PVC coupling

and clamps

Pressure

regulator

included

To household

1. Removing the

pre-assembled ejector

2. Removing the

pre-assembled nozzle

and venturi.

3. Install the included

nozzle and venturi for

deep well application.

deep well ejector kit

place in well

Ejector Installation

What is the ejector?

water from

pump

well water sucked

up by venturi action

Additional

items

needed

QTY Internet#

1-1/4 in Foot Valve

1-1/4 in Priming Tee

1 in Female PVC adaptor

1/2 in pressure relief valve

1-1/4 in Coupling (required if using PVC pipe)

1/2 in x 1/2 in Drain valve

4 in Well Seal

1-1/4in Flexible PVC Coupling

(required is using PVC pipe)

1 in Male Adaptor

10 in Tank Tee (or recommened size based

on tank size)

1/4 in Plug

2 in Pressure gauge 0-100 psi

1-1/4 in Male Adaptor

1 in Schedule 80 PVC Pipe of Flexible Pipe

1 in PVC elbow

1 in PVC coupling

1 in x 3 in nipple

1-1/4 in x 4 in Galvanized Steel Nipple

1 in Flexible PVC Coupling

(required is using PVC pipe)

205618048

100120387

100347423

205149183

203811387

205811822

322280812

100055392

100404002

205618015

100204497

205617969

203811644

320079288

100346841

100343722

100191626

100209692

202245805

1-1/4 in PVC pipe schedule 80, or

PVC pipe schedule 40

320028344

100348481

Rev. 09/27/23