EBA1840 eZ.HD Series 8MP, IP66 IR Dome Camera User’s Manual Copyright © EverFocus Electronics Corp. Release Date: May, 2019 All the images including product pictures or screen shots in this document are for example only. The images may vary depending on the product and software version. Information contained in this document is subject to change without notice. EverFocus Taiwan: 2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist.
1. Introduction EverFocus eZ.HD series cameras – EBA1840 deliver 8MP image quality. The model is equipped with 8MP CMOS sensor and provides 4mm fixed lens with ICR. Featured with True Wide Dynamic Range (T-WDR), the camera can provide clear images even under backlight circumstances where intensity of illumination can vary excessively. The EBA1840 supports both NTSC and PAL scanning systems (auto detection) and is IP66 certified. 1.
1.4 Optional Accessory BA-E310 Color / Material: White / Metal Size (Φ x H): 101 x 52mm / 3.98” x 2” Weight: 540g / 1.2lb BA-E173 Color / Material: White / Metal Size (W x D x H): 173 x 111 x 114mm / 6.81”x 4.37”x 4.49” Weight: 700g / 1.5lb 1.5 Cable Description 12VDC Power Cable Video Output Cable (BNC, 75Ohm) 2. Installation 1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw positions. Drill four holes on the surface and insert the supplied 4 Screw Anchors into the screw holes.
3. Screw the Camera Base to the surface with the supplied four Screws. a. If you want to wire the cables from the Side Cut on the Camera Base: Attach the Camera Body to the Camera Base and run the cables through the Camera Base, and then place the cable under the Side Cut. Finally, screw the Camera Base to the surface with the supplied 4 Screws. Wall Camera Body Camera Base Side Cut b.
4. Screw back the Outer Housing and adjust the camera angle simultaneously. 180° 180° 360° 5. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a monitor or DVR. UP 6. You can use the Joystick on the cable to configure camera OSD settings or switch to different video formats. Remove the Protection Cap from the Joystick before using it. Switching Video Format: • Push the joystick up for 5 sec. to switch to AHD. • Push the joystick right for 5 sec. to switch to TVI.
3.
Extern 5 6 7 Color DNR AWB Auto Autoext Preset Manual Anti-Sat. D>N Thres N>D Thres Delay IR LED Anti-Sat. Extern SW D>N Thres N>D Thres Delay 0-20 0-20 0-20 High, Middle, Low Adaptive, Off 0-20 High, Low 0-20 0-20 High, Middle, Low C-Temp R-Gain B-Gain 3000K, 5000K, 8000K 0-20 0-20 Color Gain 0-20 High, Middle, Low, Off Sharpness 0-10 Gamma 0.45, 0.55, 0.65, 0.
CB Level CR Level Trans Det Window 8 Motion On Off Output 9 System Image Range Color Space Audio Mic Color Bar Language Cam Title 10 Exit Reset Sensitivity Motion OSD Text Alarm Signal Out Off Window Use Window Zone Det H-POS Det V-POS Det H-Size Det V-Size 0-10 On, Off On, Off On, Off 0-20 0-20 0-3 0-3 On, Off 0-96 0-56 0-96 0-56 Frame Rate 4K/15fps, 4MP/30fps, 1080p/30fps Freq 60Hz (auto detection) Analog Mode AHD, TVI, CVI, CVBS Confirm Yes Return Exit Full Comp User Offset 0-32 HD-CbCr, SD