EverFocus Operation Instructions 1/3” CCD 3-Axis Outdoor IR Dome Camera EBD430
Operation Instruction © 2009 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. All rights reserved.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1.Product Overview ................................................................ 5 1.1 Features ....................................................................... 5 1.2 Accessory Parts List.................................................... 6 1.3 Specifications .............................................................. 7 1.4 Dimensions................................................................... 8 1.5 Camera Component Description.................................. 9 1.
C CH HA AP PT TE ER R 1 2 P IRNOSDTUA CL TL AOTVI E OR NV I E W Chapter 1 1.Product Overview Equipped with a SONY Super HAD CCD II and removable IR cut filter, the EBD430 produces a clear and sharp picture at night or in low light. The long range IR LEDs illuminate up to 30m/98 feet, which allows EBD430 to capture images in complete darkness. Designed with 3-Axis rotation flexibility, you can easily position the camera at all angles.
C CH HA AP PT TE ER R 1 2 P IRNOSDTUA CL TL AOTVI E OR NV I E W 1.2 Accessory Parts List Please be careful when you unpack the box to avoid any damage to the electronic device inside.
C CH HA AP PT TE ER R 1 2 P IRNOSDTUA CL TL AOTVI E OR NV I E W 1.3 Specifications Pickup Device Video Format Scanning System Picture Elements Horizontal Resolution Sensitivity S/N Ratio Electronic Shutter Lens Type Back Light Comp. Auto Gain Control Auto White Balance True Day/Night Gamma Correction Video Output Sync.
CC HH AA PP TT EE RR 21 IPNRSOTDAUL C LT A TOI V OE NR V I E W 1.4 Dimensions 116.97mm(W) x 144.07mm(H) x 138.9mm(D) /4.6”(W) x5.7”(H) x 5.
CCHHAAPPTTEERR 21 IPNRSOT DA UL C LT A TOI V OE NR V I E W 1.5 Camera Component Description Camera Base Fixing Ring Fixing Screws 3-Axis Rotation Gimbals Zoom Control Focus Control 1.6 Related Products L Type Bracket Recommended for outdoor installation to protect and tamper-proof the wiring.
C H A P T E R 2 I N S T A L L A T I O N Chapter 2 2.Installation This chapter will describe, in general terms, how to install the EBD430 camera. STEPS: 1. Wire and mount the camera, See 2.1 2. Adjust the camera position, See 2.2 3. Adjust focus and zoom, See 2.3 Warning • • To prevent electrical shock, turn off the electrical power before making electrical connections. Do not expose the appliance to water or moisture, nor try to operate it in wet areas. 2.1 Wiring and Mounting 2.1.
C H A P T E R 2 I N S T A L L A T I O N Screws A,B,C,D Camera base Outlet hole Power/Video cable hole 2.1.2 Mounting 1. Remove the camera base from the fixing ring by turning the ring it counter clockwise. 2. Fix the camera base to the ceiling or wall by using the 4 screws provided. 3. Extend the cables to be connected to power and video through the ceiling or wall. 4. Reattach the camera to the base by turning the fixing ring clockwise.
C H A P T E R 2 I N S T A L L A T I O N *Warning* • • • To prevent electrical shock, turn off the electrical power before making electrical connections. Do not connect high voltage power to the camera. It may damage the camera. Do not short circuit the power leads or expose the wires when connecting the power supply to the camera.
C H A P T E R 2 I N S T A L L A T I O N 2.2 Adjusting Camera Position 1. Attach the fixing ring with the dome body to the camera base by turning it clockwise. Please do tighten it to camera base at this step, so that you can aim the camera. 2. Adjust the direction of the camera to get the direction of view you want. 3. Twist the fixing ring clockwise tightly to lock it to the camera base. Camera Base Fixing Ring Vertically Adjust up and down Horizontally Adjust 360o 4. Tighten fixing screws.
C H A P T E R 2 I N S T A L L A T I O N 2.3 Adjusting Zoom and Focus There are two rings for adjusting focus and zoom. 1. Adjust the outer ring to the right and left to adjust focus 2. Adjust the inner ring to the right and left to zoom in or zoom out. Note: There is a screw located in the focus ring and the zoom ring for waterproofing purposes only. These are NOT set screws!! Please don’t loosen or remove them.
C H A P T E R 2 I N S T A L L A T I O N Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw Europe Office: Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany TEL: +49-2822-9394-0 FAX: +49-2822-939495 www.everfocus.de USA L.A. Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.everfocus.