EBD431e Indoor/Outdoor Ball Camera 700TVL, 3‐Axis, IP66, IR User’s Manual Copyright © EverFocus Electronics Corp, Release Date: August, 2012
CAUTIONS 1. Do not install the camera near electric or magnetic fields. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein. 3. Try to avoid facing the camera toward the sun. 4. Keep the power cable away from water and other liquids and never touch the power cord with wet hands. 5. Never install the camera in areas exposed to oil, gas or solvents. 6. Do not operate the camera beyond the specified temperature or humidity.
EBD431e 1. INTRODUCTION The EBD431e Ball camera is equipped with a 1/3” Sony 960H CCD image sensor providing resolution of 700 TVL. Featured with the Digital Wide Dynamic Range (D‐WDR) function, the camera can provide clear images even under back light circumstances where intensity of illumination can vary excessively. The EBD431e comes with 36 IR LEDs, supporting up to 20m (~65ft.) IR distance in night vision. The removable IR cut filter allows the camera to provide True Day/Night function.
EBD431e 1.2 PACKAGE CONTENTS 1. EBD431e camera x 1 2. Mounting Template x 1 3. User Manual x 1 4. Accessory kit x 1 (4 Screws, 4 Anchors, 5. Power Adapter Pigtail x 1 1.3 1 Adjustment Screw, 1 Hexagon Wrench) CABLE DEFINITIONS Cable Name Description Connects to the 12V DC power source. You can Power Cable optionally use the supplied Power Adapter Pigtail or a power adapter. Video‐Out Cable Connects to a DVR or a portable monitor for adjusting (BNC) camera angles.
EBD431e 2. SPECIFICATIONS Pickup Device Video Format Picture Elements Horizontal Resolution Sensitivity S/N Ratio Electronic Shutter Video Output Gamma Correction Lens Type Auto Gain Control White Balance Sync. Mode True Day/Night DNR D‐WDR IR LED IR Wavelength IR Distance 1/3" SONY 960H CCD NTSC or PAL (depends on model selected) 1020 x 508 (NTSC), 1020 x 596 (PAL) 700 TVL 0.01 Lux / F=1.2; 0 Lux IR On Over 50dB (AGC off) 1/50 (1/60) ~ 1/100,000 sec. BNC 1.0 Vp‐p ,75ohm 0.45 Varifocal Lens f=2.8~10.
EBD431e 3. INSTALLATION & OPERATION 1. Unscrew the Set Screw using the supplied Hexagon Wrench and then remove the Outer Housing from the Camera Base. 2. Paste the supplied mounting template onto a desired location on the ceiling / wall. Drill the four small holes for screwing the camera with the supplied Screws and Anchors, and the circle in the middle only if you wish to run the wires into the wall. 3. Insert the supplied 4 Anchors into the 4 holes on the ceiling / wall. 4.
EBD431e b. If you want to wire the cables through the wall, attach and then screw the Camera Base to the ceiling / wall. Attach the Camera Body to the Camera Base. 5. Connect the camera to the 12V DC power source using the supplied Power Adapter Pigtail or a power adapter. 6. Connect the camera to a DVR or a portable monitor using the Video‐Out cable for viewing the camera view while adjusting camera focus, zoom and angles. 7. Screw back the Outer Housing and adjust the camera angle simultaneously. 8.
EBD431e 4. Configuration in the OSD Menu You can use the external 5‐Axis OSD Joystick controller to configure camera settings in the OSD menu. 4.1 OSD Joystick OSD Joystick 4.2 Push the Joystick up / down to select between menu items. Push the Joystick left / right to adjust the level of the selected item. Press the Joystick to enter the submenu or exit the OSD Setup Menu.
EBD431e 4.2.1 LENS MAUNAL: No adjustment (Read Only). AUTO TYPE:DC MODE:AUTO/ OPEN /CLOSE AUTO SPEED:000~255 MODE: AUTO: Camera automatically controls the lens. OPEN: Lens fully open. CLOSE: Lens fully closed. SPEED: Speed of the lens. 4.2.2 SHUTTER/AGC AUTO AUTO HIGH LUMINANCE MODE:SHUT+AUTO IRIS / AUTO IRIS / SHUT BRIGHTNESS:000~255 LOW LUMINANCE MODE:AGC / OFF BRIGHTNESS:x0.25、x0.50、x0.75、x1.00 MODE: SHUT+AUTO IRIS: Exposure is controlled by auto electronic shutter combined with auto iris.
EBD431e 4.2.3 WHITE BAL ATW (Auto White Balance) SPEED:000~255 DELAY CNT:000~255 ATW ATW FRAME:x0.50、x1.00、x1.50、x2.00 ENVIRONMENT:INDOOR、OUTDOOR SPEED: ATW Speed DELAY CNT: ATW Delay Time ATW FRAME: ATW Frame Range Setup ENVIRONMENT: ATW Environment Range Setup PUSH The function will keep on detecting the Color Temperature, and then keeps saving up the parameter to the camera.
EBD431e 4.2.4 BACKLIGHT OFF: Disable the Backlight function. BLC: Enable the function of Back Light Compensation, using BLC Smart detection method. HLC: Enable the function of High Light Compensation. Note: Please avoid enabling the ATR and Backlight functions simultaneously. 4.2.5 ATR (Adaptive Tone Reproduction) OFF: Disable the ATR function. ON LUMINANCE LOW、MID、HIGH CONTRAST LOW、MIDLOW、MID、MIDHIGH、HIGH Note: Please avoid enabling the ATR and Backlight functions simultaneously. 4.2.
EBD431e 4.2.8 NEXT Enter to the next page. 4.2.9 EXIT Exit the OSD Setup Menu. 4.2.10 SAVE ALL After configuring the camera settings, press the Joystick to save all settings. 4.2.11 DAY/NIGHT AUTO AUTO BURST:ON/OFF DELAY CNT:000~255 DAY NIGHT:000~255 NIGHT DAY:000~255 BURST: Selects whether to output the burst signal when under Night status has been identified. DELAY CNT: Set the Night/ Day identification transfer time (Default: 4Sec.).
EBD431e BURST: Selects whether to output the burst signal. IR OPTIMIZER: The IR Optimizer function makes it possible to minimize this overexposure by optimizing the exposure control during Night operations. MODE: Set the IR OPTIMIZER operating mode. LEVEL: Adjusts the reference level of the IR Optimizer (Default: 5). EXT1 DN_IN 0[h]: Night mode EXT2 DN_IN 0[h]: Day mode 4.2.12 1[h]: Day mode 1[h]: Night mode PRIVACY OFF Select to disable the Privacy function.
EBD431e MOSAIC: Set the mask frame mosaic function to ON or OFF. Note: When the MONITOR AREA has been set to ON by the MOTION DET setting, only 4 PRIVACY AREA SEL are selectable (1/4, 2/4, 3/4, 4/4). 4.2.
EBD431e AB C D E F G H I J K LM N O PQ R S T U V WXYZ0 1 2 3 4 56 7 89- ! ”# $ % &’ ()_ ‵ , ¥ : ; < = >?@\ ^*.x+/ ←→↑↓ CLR POS 4.2.15 Each User Font The camera ID cursor moves in the direction of the arrow when the Enter operation input is performed from the status in which ←, →, ↑ or ↓ has been selected using the character selection cursor.
EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe - Germany: Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.