ED300 Series User’s Manual and Operation Instructions Version 1.
Notice This manual is presentED300 to the users of ED300 by EverFocus Electronics Corp. With years of engineering researches, EverFocus has sparED300 all efforts to provide the high quality products to the worldwide users. For the policy of continual product improvement, EverFocus reserves the right to make changes to the product specifications and documentation without notice.
Table of Contents Safety Warning...............................................................................1 Introduction....................................................................................3 Specification ...................................................................................4 Major Parts Names and Functions ...........................................5 Installation Instructions ............................................................7 Lens Adjustments.....................
Safety Warning 1. Do not expose the camera to humidity and dust. Moisture can damage the camera and cause the danger of electric shock. If the camera is mountED300 outdoors, a camera housing is requirED300. Do not install the camera at where there is greasy smoke or steam, where the humidity is too high, or where there is a lot of dust to prevent damages to the camera. 2. Do not disassemble the camera. Do not disassemble the camera body as it is dangerous and may cause the damages to the camera.
. Do not install the camera in the high temperature environment. InstallED300 the camera away from stoves, or other heat generating devices, or where it could be subject to direct sunlight as the high temperatures could cause deformation, discoloration or other damages of the camera. Install the camera at where the temperature range will stay between 0℃ to 50℃(32℉ to 122℉). 6. Cleaning Use a soft cloth to remove the dirt from the unit.
Introduction The High Resolution Dome Camera Series are compact, full functionED300 CCD Color Cameras. Their stylish appearance can be appliED300 as per installer's ideal locations on the ceiling. The dome camera designED300 with advancED300 digital processing curcuitry for high resolution 1/3" color interline transfer CCD sensor, it has DIP switch for AGC on/off, BLC on/off.
Specification Pickup device: 1/3" Interline transfer CCD Video format: NTSC/PAL Scanning system: NTSC: 525 TV lines, 60 fields/sec; PAL: 625 TV lines, 50 fields/sec. Picture elements: NTSC: 811(H) x 508 (V); PAL: 795 (H) x 596 (V) Effective picture elements: NTSC: 768 (H) x 494 (V); PAL: 752 (H) x 582 (V) Horizontal resolution: 480 TV lines Sensitivity: 1.42 lux / F=1.
Major Parts Names and Functions 《ED300》 《ED300-A》 ? ? ? ? ? ? 12 11 13 12 ? ? ? ? ? 5.
? Camera Cover ? Level Volume Control This cover will protect the camera from dust and damage. The iris level control for the lens. ? Ground Pin ? Lens For monitor use. Please see ?. This Vari-Focal Lens allows users to adjust the Zoom and Focus manually. ? Monitor Pin ? Base The c amera unit is set in the dome base when it is shippED300 from the factory.
Installation Instructions 1. Remove the plastic dome cover. 2. Lossen the two screws of the supporting bracket to remove the camera body. 3. Using four screws to fix the camera base on the ceiling. 4. Put the camera body back to the supporting bracket, then tighten the two screws to fix the camera. 5. Connect the BNC connector of the camera to a color monitor, or other video device through a 75 ohm type coaxial cable with BNC female connector at cable extension. 6.
Lens Adjustments Zoom and focus adjustments After the camera was installED300, the zoom and focus of the lens must be adjustED300. 1. Loosen the zoom ring knob, and then turn the ring towards or as necessary to obtain the desirED300 view range. W side (Zoom out) The viewing range will be wider and the subject is smaller. T side (Zoom in) The viewing range will be smaller and the subject is larger. 2.
Adjustments Auto Gain Control Adjustment AGC ON: The sensitivity increases automatically when the light is low. AGC OFF: A low-noise picture is obtainED300 under a low light condition. Back Light Compensation Adjustment When the background of the subject is very bright and the subject itself is dark, set the BLC (Back Light Compensation) ON. The BLC will measure the light of the image center and the lens iris will automatically set for optimum image quality.
EverFocus Electronics Corp. Head Office: European Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw USA Office: Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany www.everfocus.de TEL: 49-2822-9394-0 FAX: 49-2822939495 Beijing Office: 2445 Huntington Drive, San Marino, CA 91108, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.everfocus.
