Instruction Manual 16/9/4 Channel Digital Video Recorder EDVR SERIES
EVERFOCUS ELECTRONICS CORPORATION EDVR SERIES Instruction Guide © 2005 EverFocus Electronics Corp www.everfocus.com All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation. Release Date: Dec.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Declaration This equipment has been tested and found to comply with the limits for a CE Class A digital device. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In a domestic environment this product may cause radio interference. In which case the user may be required to take adequate measures.
TABLE OF CONTENTS 1. PRODUCT OVERVIEW ..............................................................................................1 1.1 Features.................................................................................................................1 1.2 Specifications.........................................................................................................2 1.3 Front Panel Keypads .............................................................................................4 1.
4.1 Instant (N) Recording Setup ................................................................................66 4.2 Schedule Recording Setup ..................................................................................67 4.3 Event Recording Setup ........................................................................................68 5. PLAYBACK OVERVIEW...........................................................................................72 5.1 Basic Playback .................................
APPENDIX C: RJ45 (RS485) PIN ASSIGNMENT......................................................131 APPENDIX D: LAPSE MODE RECORDING TABLE .................................................132 TROUBLESHOOTING ................................................................................................
Safety Warning WARNING To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION Do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Safety Precautions Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation opening or slots on the cover. Do not drop metallic parts through slots. This could permanently damage the appliance? Turn the power off immediately and contact qualified service personnel for service. Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside.
Safety Precautions Read Instruction All the safety and operating instructions should be read before the unit is operated. Retain Instructions The safety and operating instructions should be retained for future reference. Heed Warnings All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions All operating and use instructions should be followed. Cleaning Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Chapter 1 1. Product Overview The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology, resulting in enhanced recording capacity and improved network image transmission speed with high image quality. Comprehensive features and extended event recording settings enable the almost universal application of this DVR series. 1.
1.
VGA USB Ethernet Archive RS-485 Power Source Power consumption Dimension Weight Operating Temperature Yes Yes, 2 x USB2.0 interface device. 1 for archiving & 1 for mouse. Yes, RJ45 connectors for network communication USB for archiving for PTZ and/or control keyboard AC 100~240V F:70W; D:50W Full size: 430mm (W) x 402.5mm (D) x 72mm (H) 6.
1.3 Front Panel Keypads Keys: 1 ○ REC Press this key to start instant recording. 2 ○ STOP Press this key to stop recording and playing back. 3 ○ PLAY Play Back. 4 ○ PAUSE Press this key to pause the playback picture. 5 ○ SEARCH Press this key to enter the SEARCH MENU. 6 ○ COPY Pressing COPY key at live mode will enable you to enter COPY menu. In playback mode, the current playback position is stored as image export start position.
9 ○ SELECT Press this key to select, to assign a camera to a display, to adjust screen display, and so on. 10 ○ MODE Switch PIP, 4, 7, 9, 10, 13 and 16 displays in Live and Playback modes. 11 ○ ZOOM In full screen mode, 2x electronic zoom. Zoom screen can be moved through JOG. Enter key changes the direction. Further zoom key actuation switches the electronic zoom off. In multiscreen mode: Image orientation adjustment. Use the JOG to adjust the image to the respective monitor type.
13 ○ CALL Press this key to enter and set up CALL MENU. 14 ○ Menu Press this key to enter or quit MAIN SETUP MENU. 15 ○ Shuttle and Jog Dial Shuttle: In the Playback mode, turn the Shuttle dial to fast forward/rewind the video. In the Pause mode, turn the Shuttle dial to slow forward/rewind the video. In the event list, turn the Shuttle to change pages. Jog Dial: In the Pause mode, turn the Jog dial to forward/rewind the video.
21 ○ LCD Panel To display Date and Time, and other system information. 22 ○ Remote Control IR remote control receiver.
1.4 Back Panel Connections For models: EDVR16D1/F1, EDVR16D2/F2, EDVR9D1/F1, EDVR4D1/F1 For model: EDVRD3 3 4 13 ○ ○ ○ 5 ○ 2 ○ 7 ○ 9 ○ 11 ○ 12 ○ 10 ○ 8 ○ 1 ○ 6 ○ POWER 1 ○ Main Power plug Connect power jack (AC 100~240V). 2 ○ Audio IN Audio inputs 1~4 for recording, and it can be enabled by setting to “YES” or “NO” in the RECORD SETUP MENU. Audio OUT Connect an audio output to a monitor or other device.
4 ○ This connector is used for the main monitor display, a number of different display modes may be selected for viewing. CALL MONITOR This connector is used for the call monitor. This monitor can only display a full screen, but not able to enter Setup Menu. VIDEO IN 5 16 CH: ○ VIDEO OUT (1~16): BNC connectors for video looping out 1~16. VIDEO IN (1~16): BNC connectors for video input 1~16. 9 CH: VIDEO OUT (1~9): BNC connectors for video looping out 1~9.
RS232 8 RS232 connector ○ 9-pin Sub-D control input/output for service purpose. RS485 9 RS485 connector ○ RJ 45 Connector to cascade multi Digital Video Recorder. VGA 10 VGA ○ Connect to the monitor that has VGA input. Remote Control (extension cable is optional) 11 Remote Control ○ Connector to connect IR extension cable that has an IR remote control receiver. SCSI (Only available for EDVR16D3) 12 SCSI Connector ○ For connecting the optional extension unit.
1.5 Monitor Display The status information of the cameras or machine will show up, and be located at different places on the screen. 1. Channel tag 2. Event sign 3. Select sign 4. Play status bar 5. Record status bar 1 ○ Channel tag A channel tag indicates the channel name of the screen. 2 ○ Event sign Event signals which are small icons with a capital letter and red background show the events on each screen. There are totally 6 different signals which are: A Alarm event.
The sequence display is located on display with a “＊” sign in the last display of the screen. The S sign will replace “＊” sign in the display when sequence occurs. Note: Sequence is invalid when the multiscreen display can show all the cameras. Temperature indication. T When HDD’s temperature is overheated. Overheat temperature is determined in HDD TEMPERATURE of WARNING SETUP MENU. F Fan fail indication. When the fan fails to work normally.
5 ○ Record status bar The record status bar appears when you enable a status bar on the screen (Please see 8th item of DISPLAY). Three parts which are current date, record status (% of space used for recording) and current time. Current Date Record Status Event Current Time HDD/Fan Status 1. Current date The current date which is set in the TIME/DATE SETUP MENU. 2.
Chapter 2 2. Installation The installations described below should be done by qualified service personnel or system installers. 2.1 Packing Please check accessories in the packing before the installation. 2.2 System Floorplan Please refer to the following diagrams for the system connections. Note: Monitor and Camera must be purchased separately. Diagram 2.
2.3 Basic Wiring Instructions 1. Power Connect the power source or adapter into the power socket. 2. Cameras Connect each cameras video output to the video input on the digital video recorder shown in diagram 2.1. Note: At least one camera (CH 1) must be connected before the system is running for the auto detection of video standard to take effect. 3. Audio Input The camera audio output or Microphone is connected to the audio input terminal at the rear panel. 4.
9. Call Monitors Connect the call monitor output connectors to a call monitor. The call monitor display selected live cameras in full screen format. Note: The call monitor will only display one full screen camera at a time. 2.4 Final Install Process Once you have completed the basic wiring installation and the hard disk drive installation you are ready to turn on the DVR. Simply plug the power source you installed earlier. The POWER LED lights will light up if power is normal.
Chapter 3 3. DVR Menu Setup Assuming you have completed the first two chapters of this manual. You are now ready to begin setting up the digital video recorder. The following chapter will walk you through the detailed DVR Menu step by step and how to set the DVR for your specific application. To begin this process, press the MENU key. Once inside the main menu you will find there are 12 setup option pages as follows. MENU Press the MENU key to enter the MAIN MENU.
3.1 Time/Date Setup Menu Diagram 3.2 Diagram 3.2 is a screen shot of the TIME/DATE SETUP MENU. This menu is used to set up the correct time and date for your region of the world. You are able to setup daylight savings as well as synch it with an internet based time server. In the TIME/DATE SETUP MENU the following fields are defined as follows: 1. TIME FORMAT This field represents the time format on the DVR. There are two time formats that are 12 HOUR and 24 HOUR to be selected. 2.
3. DATE FORMAT This field represents the date format on the DVR. To change this, simply use the Jog Dial on the DVR. There are three date formats which are YYYY-MM-DD, MM-DD-YYYY and DD-MM-YYYY to be selected. 4. DATE This field represents the date on the DVR. To change this, simply use the Jog Dial on the DVR. There are three date formats which are YYYY-MM-DD, MM-DD-YYYY and DD-MM-YYYY to be selected. The date is represented as follows: Year: 2000~2037 / Month: 01~12 / Date: 01~31 (Day of Week) 5.
To set the start time of daylight saving time: To set the start “FROM” time and “TO” time of daylight saving time. 7. END TIME To set the end time of daylight saving time. To set the end month of daylight saving time: Dial the jog to set the end month. JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC To set the end week of daylight saving time: Dial the jog to set the end week. 1 ST 2 ND 3 RD 4 TH LAST To set the end date of daylight saving time: Dial the jog to set the end date.
Under Dos Prompt, type “C:\Ping Pool.NTP.ORG to find out the IP address of NTP Server. Diagram 3.3 10. TIME ZONE You can set the time zone where you locate if you connect to network and enable time synchronize.
DAY WEEK MONTH 3.2 Camera Setup Menu Diagram 3.4 Diagram 3.4 is a screen shot of the CAMERA SETUP MENU. This menu will walk you through setting up the Camera Recording Speeds, Camera titles, PTZ ID, covert modes, and recording quality. In the CAMERA SETUP MENU the following fields are defined as: 1. TITLE The title setting allows you to assign a title to each camera input. Titling with 12 characters is supported in each channel. To change this, simply use the Jog Dial on the DVR.
3. INSTALL/COVERT For installation of camera; select “ON” to enable a camera, and “OFF” to disable it. Please make sure to stop recording before making change of INSTALL. To take full advantage of the record resource, switch the Uninstalled Camera Ports to OFF in this section. For COVERT, select “ON” to cover a camera, and disable the screen in live mode to show up. However, the image is recorded, and can be played back by user who has playback right.
720x480 Average size per image Video Source Simple: Complex: Lower: 8.04KB 12.33KB Low: 8.42KB 13.7KB Basic: 10.15KB 16.72KB Standard: 11.86KB 19.56KB High: 14.72KB 24.63KB Superior: 18.60KB 30.05KB Video Source Simple: Complex: Lower: 3.53KB 7.82KB Low: 3.87KB 8.36KB Basic: 4.21KB 8.9KB Standard: 4.92KB 9.54KB High: 5.62KB 10.17KB Superior: 6.41KB 12.89KB Video Source Simple: Complex: Lower: 1.76KB 4.56KB Low: 1.87KB 4.87KB Basic: 1.97KB 5.46KB Standard: 2.
NORMAL IPS recording rate for manual or scheduled recording and recording controlled through “REC IN” input contact. The maximum image rate is limited to: Max. image rate per camera = max. DVR recording rate / number of installed cameras. Max.
7. SUMMARY Diagram 3.5 Dial Jog to change items in the SUMMERY table. All cameras’ statuses are shown in the SUMMARY table. The table is for checking camera overall statuses only, not for setting. Note: The SUMMARY table also exists in ALARM, MOTION and VLOSS SETUP MENU. All of these SUMMARY tables are also for checking particular overall statuses, not for setting. 8.
3.3 Record Setup Menu Diagram 3.6 Diagram 3.6 is a screen shot of the RECORD SETUP MENU. This menu is for setting up the options for recording. We define recording as something on which sound or visual images have been recorded. In the RECORD SETUP MENU the following fields are defined as follows: 1. RECORD AUDIO YES: Audio will be recorded when machine is recording. NO: Audio will not be recorded when machine is recording. 2.
4. WATER MARK ON: Recording is overlaid by a visible watermark (“W”). OFF: No watermark. 5. RESOLUTION The resolutions for NTSC are 720x480, 720x240 and 360x240 to be selected. Its default value is 720x240. The resolutions for PAL are 720x288, 720x576 and 360x288 to be selected. Its default value is 720x288. NOTE: Selecting a certain resolution will determine the amount of IPS the DVR will support. Model D1/F1 D2/F2 D3 6.
3.4 Alarm Setup Menu Diagram 3.7 Diagram 3.7 is a screen shot of the ALARM SETUP MENU. An alarm is defined as an electrical, electronic, or mechanical device that serves to warn of danger by means of a signal. In this case the signal triggers the recorder to start recording the alarmed event. This menu contains all the alarm operations and options needed to successfully complete an alarm recording. In the ALARM SETUP MENU the following fields are defined as: 1.
N.C. Trans.: When the alarm is triggered, buzzer, alarm output and alarm recording start to function no matter how long the alarm duration is set until you set it back to N.C. 3. LOG YES: Select YES if you wish to record Alarm Events in the Log. NO: Select NO if you do not wish to record Alarm Events in the Log. 4. ACTIVE CAMERA This field is to activate camera you want to have the alarm enabled too. For example if you had an external motion detector on camera one you would set this option to camera one.
10. ALARM NETWORK YES: Enable alarm network. NO: Disable alarm network. 11. MAIN MON: Display on a main monitor when an alarm occurs. NO CHANGE: No change on the display in the main monitor when an alarm occurs. FULLSCREEN: A full screen of the active camera will display when an alarm occurs. 12. CALL MON: Display on a call monitor when an alarm occurs. NO CHANGE: No change on the display in call monitor when an alarm occurs.
3.5 Motion Setup Menu Diagram 3.8 Diagram 3.8 is a screen shot of the MOTION SETUP MENU. We define motion as a change of pixilation in the field of view, which is detected by the digital video recorder, and triggering the recorder to start recording. This menu is for setting up the digital recorder for motion recording on a per camera basis. In the MOTION SETUP MENU the following fields are defined as follows: 1. MOTION: This field is to turn motion detection ON or OFF. The default value is Disable.
3. LOG YES: Select YES if you wish to record Motion Events log in the HDD. NO: Select NO if you do not wish to record Motion Events log in the HDD. 4. DURATION The amount of time a motion event will record - from 1 sec to 99 seconds. The default value is 5 seconds. To change this, simply use the Jog Dial on the DVR. 5. ALARM OUTPUT This will transmit a signal to another device.
Dial Jog to change items in the SUMMARY table. All alarm’s statuses are shown in SUMMARY tables. These tables are for checking alarm overall statuses, but not for setting. 11. Press SELECT to edit MOTION AREA. Enter a desired channel and press SELECT to edit a motion area. Please make sure that MOTION is set as “Enable” before entering the motion detection area. In the motion edit mode: The default motion area of each camera is entire screen which displays in light green.
MENU COPY ENTER SEARCH PAUSE - EXIT - SELECT AREA - CHANGE DIR - ON AREA - OFF AREA 35
3.6 VLoss Setup Menu Diagram 3.9 Diagram 3.9 is a screen shot of the VLOSS (Video Loss) SETUP MENU. VLoss event is caused by no video signal input for the channel. Usually it happens when no power supply for the camera or the camera fails. How to set up system response for VLoss case is introduced in this section. In the VLOSS (Video Loss) SETUP MENU the following fields are defined as follows: 1. VLOSS: ENABLE: Enable video loss detection. DISABLE: Disable video loss detection. 2.
4. ALARM OUTPUT This will transmit a signal to another device. The setting of alarms are NONE = not activated, 1 = output signal 1 transmitted, 2 = output signal 2 transmitted, 3 = output signal 3 transmitted and 4 = output signal 4 transmitted. To change this, simply use the Jog Dial on the DVR. (Only EDVR16D3 model has 4 alarm outputs, all the rest models have only 1 alarm output). 5. ALARM EMAIL Select “YES” for sending an email when vloss occurs.
3.7 Network Setup Menu Diagram 3.10 Diagram 3.10 is a screen shot of the NETWORK SETUP MENU. This menu is for setting up the configurations for networking to the DVR. For more detail about network setup, please refer to CH.10~13. There are 6 subentries that are CONFIG, ALARM, EMAIL, PASSWORD, PPPoE and DDNS in the NETWORK SETUP MENU. Each of them has to be set up completely before the network functions. Please refer to the Networking Chapters (CH.
FIXED IP: User can set the fixed IP for network connection. DHCP: DHCP server in LAN will provide the dynamic IP for network connection PPPoE: This is a DSL connection application, ISP will ask user to input user name and password. When you choose this option, please go to PPPoE configuration menu for setting PPPoE configuration. 2. IP Address This field is to set a static IP Address for the DVR. A static IP address is an IP address whose value does not change. It is suggested to use a static IP address.
YES: to enable Multicast function. NO: to disable Multicast function. 7. IP ADDRESS This is the router’s IP address. Please input the IP address of router. 8. PORT Port of Multicast. Please configure the port number. 9. HTTP PORT The default port number is 80. User can change it to different port number for HTTP/WEB communication between DVR and client PC. 10. CONTROL PORT The default port number is 1600. User can change it to different port number for controlling comment between DVR and client PC.
3.7.2 ALARM (NETWORK) DVR can send out Alarm message to an Alarm Server (PowerCon4). In the ALARM of the NETWORK SETUP MENU, we define: Diagram 3.11 Note: Since every Network Configuration is different, please contact your Network Administrator or ISP for how to assign those IP addresses and port numbers. 1. PROTOCOL: Select which communication protocol with Alarm servers or Alarm receiving clients. TCP: communicate with client via TCP protocol. UDP: communicate with client via UDP protocol 2.
5. SERVER 2 Assign the IP address of Alarm server 2. 6. SERVER 3 Assign the IP address of Alarm server 3. 3.7.3 EMAIL In the EMAIL of the NETWORK SETUP MENU, we define: Diagram 3.12 1. SMTP SERVER Assign the SMTP (e-mail) server’s name. Note: please do not enter IP address. 2. PORT NUMBER Assign the port number for SMTP server. 3. AUTHENTICATION Select “YES”, if the SMTP server requires Authentication (user name / password) 4. USER Input the login user ID if the SMTP server requires Authentication.
5. PASSWD Input the password if the SMTP server requires Authentication. 6. RECEIV. EMAIL ADDR Input the e-mail address for receiving e-mail message when the EVENT is enabled and triggered. For example: In Motion Setup Menu, if the “EMAIL/NETWORK” is set to “YES”, this e-mail address will receive a text message and an “ARV” format of a still image from DVR when Motion is triggered. This “ARV” file can be played back by opening “DVRViewer.
3.7.4 PASSWORD In the PASSWORD of the NETWORK SETUP MENU, we define: Diagram 3.13 User-Name/Password/Level: This category is to set up the users that will log into the network. Please remember that this portion of the Network setting menu is set up in column format. The default User Name = ADMIN The default Password = 11111111 (only numeric) There are 2 level types: 1. Play: Allows the user to view live video, perform a search, playback and control the PTZ camera (if one is connected) 2.
3.7.5 PPPoE In the PPPoE of the NETWORK SETUP MENU, we define: Diagram 3.14 1. USER User name that is provided by ISP for PPPoE Connection 2. PASSWD Password that is provided by ISP for PPPoE connection 3. PRIMARY DNS An IP address of DNS server that is provide by ISP. 4. SECONDARY DNS If your ISP provides you an IP address secondary DNS, please set it in here.
NOTE: 1) Please complete all settings in PPPoE Setup Menu, then return to CONFIG for changing IP CONFIG to PPPoE. Otherwise, PPPoE settings won’t be valid. 2) If you select first PPPoE in IP CONFIG of CONFIG option, while PPPoE settings haven’t been done yet, then PPPoE function won’t work. Diagram 3.
3.7.6 DDNS In DDNS of the NETWORK SETUP MENU, we define : Diagram 3.16 For example: A user had applied for a DDNS account from Http://www.dyndns.org. User name: TEST Password: TEST Domain name ethin.dyndns.org. 1. SERVER DDNS provider. 2. USER User name of the account. 3. PASSWD Password of the account. 4. RECORD ID Record ID.
5. FQDN The domain name of this account. Users can connect to DVR that uses dynamic IP address by entering the domain name “ethne.dyndns.org” in IE browser. (This domain name is only an example, the DDNS account that user applies may differ from this example). They don’t have to know the IP address.
3.8 Schedule Setup Menu Diagram 3.17 Diagram 3.17 is a screen shot of the SCHEDULE SETUP MENU. In this menu you can set a unique timer any day of the week to start recording from a specified start time to an end time. This menu works together with the camera menu, you will notice 1~8 TP (time period), which is also seen in the camera menu. In the SCHEDULE SETUP MENU the following fields are defined as: 1. DAY This field represents the day of the week you wish to set the timer record for.
2. START This field is used to set the time you wish to start the timer recording. To change this, simply use the Jog Dial on the DVR. Hour: 0 ~ 23 in 24 hour time format; 1~12 in 12 hour time format. Minutes: 00 ~ 59 Note: To record all day long: 12:00am~12:00 am for 12-hour-format 00:00~00:00 for 24-hour-format. 3. END This field is used to set the time you wish to stop the timer recording. To change this, simply use the Jog Dial on the DVR.
3.9 Disk Setup Menu Diagram 3.18 Diagram 3.18 is a screen shot of the DISK SETUP MENU. This menu is for viewing Disk information and formatting the disks. For every configuration change or initial setup we recommend formatting the Hard Disk. In the DISK SETUP MENU the following fields are defined as follows: 1. DISK VIDEO DELETE Press SELECT to start delete. A delete disk confirmation window will show up after pressing SELECT button.
2. THERMOMETRIC SCALE Select CELSIUS or FAHRENHEIT for thermometric scale of the disk. 3. NO/SIZE/C or F/Start/End Time Show the number of drives, the size of each drive and the temperature as well as the days and times range stored on the hard drive. 1 The number of disk may differ depending on the model. Note ○ 2 For EDVR16D3 model, SCSI can be added, maximum of 50 external disk arrays.
3.10 Control Setup Menu Diagram 3.19 Diagram 3.19 is a screen shot of the Control Setting Menu. This menu is to define the settings for DVR remote control through serial interface in the RS232/RS485 menu. The following fields are defined in the Control Setting Menu: RS232: 1. RS232 Baud Rate This field is to set the speed at which is used to transmit instruction or information through the RS232 port on the DVR.
4. RS232 Data Bit This field is the data bit at which you will be transferring. There are two settings for this option: 8 or 7. The default is set to 8. To change this, simply use the Jog Dial on the DVR. RS485: 5. RS485 Baud Rate This field is to set the speed at which is used to transmit instruction or information through the RS485 port on the DVR. There are six different speeds, 2400, 4800, 9600, 19200, 38400 and 57600 BPS. The default setting from the factory is 9600 BPS.
3.11 Warning Setup Menu Diagram 3.20 Diagram 3.20 is a screen shot of the Warning Setup Menu. This menu is to set the warning system settings. If any critical errors were to arise, this portion of the menu would be for error handling. For example if you set the fan buzzer on and the fan wasn’t able to turn on then you would here an alarm go off. In the Warning Setup Menu the following fields are defined as: 3.11.1 FAN FAULT In FAN FAULT, we define: 1. BUZZER: Fan buzzer.
3. ALARM DURATION Permanent 4. NETWORK ALARM YES: To enable network alarm. NO: To disable network alarm. 5. SEND EMAIL: YES: Send an email when the fan does not work. NO: Do not send an email when the fan does not work. The email address can be set in the NETWORK SETUP MENU.
3.11.2 HDD TEMP In HDD TEMP, we define: Diagram 3.21 1. BUZZER: HDD TEMPERATURE buzzer. ENABLE: To enable a buzzer when HDD’s temperature is higher than the temperature set in “SET TEMPERATURE”. DISABLE: To disable HDD TEMP. Buzzer. 2. ALARM OUTPUT This will transmit a signal to another device. The setting of alarms are NONE = not activated, 1 = output signal 1 transmitted, 2 = output signal 2 transmitted, 3 = output signal 3 transmitted and 4 = output signal 4 transmitted.
5. SEND EMAIL YES: Send an email when HDD’s temperature is overheated. NO: Will not send an email when HDD’s temperature is overheated. The email address can be set in the NETWORK SETUP MENU. 6. STOP RECORD YES: Stop recording when HDD’s temperature is overheated. NO: Will not stop recording even when HDD’s temperature is overheated. 7. SET TEMPERATURE: When HDD’s temperature is higher than 60°, then all other settings in HDD TEMP.
3.11.3 NO HDD In NO HDD, we define: Diagram 3.22 1. BUZZER: NO HDD buzzer. ENABLE: To enable a buzzer when no HDD has been found. DISABLE: To disable NO HDD buzzer. 2. ALARM OUTPUT This will transmit a signal to another device. The setting of alarms are NONE = not activated, 1 = output signal 1 transmitted, 2 = output signal 2 transmitted, 3 = output signal 3 transmitted and 4 = output signal 4 transmitted. To change this, simply use the Jog Dial on the DVR.
5. SEND EMAIL: YES: Send an email when no HDD has been found. NO: Will not send an email when no HDD has been found. The email address can be set in the NETWORK SETUP MENU. 3.11.4 HDD FULL In HDD FULL, we define: Diagram 3.23 1. BUZZER: HDD FULL buzzer. ENABLE: To enable a buzzer when HDD is full. DISABLE: To disable HDD Full buzzer. 2. ALARM OUTPUT This will transmit a signal to another device.
simply use the Jog Dial on the DVR. (Only EDVR16D3 model has 4 alarm outputs, all the rest models have only 1 alarm output). 3. ALARM DURATION Buzzer noise and event record duration of an alarm, from 1 sec to 99 seconds. The default value is 5 seconds. 4. NETWORK ALARM: YES: To enable network alarm. NO: To disable network alarm. 5. SEND EMAIL: YES: Send an email when HDD is full. NO: Will not send an email when HDD is full. The email address can be set in the NETWORK SETUP MENU.
3.12 System Setup Menu Diagram 3.24 Diagram 3.24 is a screen shot of the SYSTEM SETUP MENU. This menu is for setting up any additional options and restoring defaults to the digital recorder. In the SYSTEM SETUP MENU the following fields are defined as follows: 1. SYSTEM VERSION: Current system firmware version. 2. SYSTEM VIDEO FORMAT: NTSC or PAL. System can detect the input signal type automatically from camera 1 while system is booting up. Users do not need to set it up.
NO: Press “ENTER” key to leave “LOAD/SAVE CONFIGURATION”. 4. UPDATE SYSTEM SOFTWARE: Turn the jog to enter the selection window. YES: Select YES to update system software from USB by pressing SELECT to start. NO: Select NO for canceling updating by pressing SELECT to start. Note: 1 System will ask you to stop recording if you confirm to update when system is ○ recording. 2 USB device must be inserted properly before updating system software.
7. SYSTEM PASSWORD ENABLE YES: Select YES to enable the password function. NO: Select NO to disable the password function. 8. PASSWORD and RIGHTS: The login passwords here are used to operate and set up this machine locally not from the remote tcp/ip connection. The different login passwords indicate the different level of users, and no login name is necessary. The digit will appear instead of a “＊” sign when the cursor is moved on it.
User Level and Right LEVEL DISPLAY MODE ZOOM SELECT SEQ CALL MENU COPY SEARCH PLAY STOP REC PAUSE LEVEL-3 ADMINISTRATOR OK OK OK OK OK OK OK OK OK OK OK OK OK LEVEL-2 OPERATOR OK OK OK OK OK OK NO OK OK OK OK OK OK Note: The above table will be updated if there is any change.
Chapter 4 4. Recording Overview Before continuing with the Recording Overview please be sure to have reviewed DVR Menu Setup (Chapter 3) specifically the camera & schedule. You are now ready to begin setting up the machine for recording. This chapter will show you how to setup the recorder for three basic types of recording: Instant recording, scheduled recording, and event recording.
Note: If STOP key is pressed while machine is recording or playing video, the playing function will be disabled first. If STOP key is pressed twice the DVR will come out of record mode completely. 4.2 Schedule Recording Setup Set up the DAY, START time, END time and then enable the SET in the SCHEDULE SETUP MENU. Diagram 4.1 Please refer to SCHEDULE SETUP MENU, to see setting procedure and more details.
4.3 Event Recording Setup We will now define two event recording types ALARM and MOTION. After the event recording is enabled, the DVR will start an event recording when an event occurs. For instance, when motion activity is detected by the DVR it will begin recording at the specific IPS set under event column. Or when an alarm is detected by the DVR it will begin recording at the specific IPS set under event column. In order to start an event recording, you will NEED to perform the following: 1.
2. When the event and schedule are set, enter the CAMERA SETUP MENU to set the event recording speed (IPS) of the camera in the time period (TP) section. Diagram 4.
3. After enabling an event, you need to set a time period (TP) in the SCHEDULE SETUP MENU. An event recording must be set in a scheduled time period (TP). You can refer to the SCHEDULE SETUP MENU for time period configurations (Chapter 3.8). Diagram 4.4 Note: 1 Set the normal record speed as 0 IPS in the CAMERA SETUP MENU, and Set the time ○ period (TP) from 00:00 to 00:00 daily in the SCHEDULE SETUP MENU if you only want to record an events activity recording (motion or alarm).
DVR provides a record function which is triggered by external signal via the 19th pin of the ALARM INPUT / OUTPUT port. When the record input signal is pulled low constantly, DVR will start to record. The system will stop recording when the record input signal is not pulled low. Note: Please check APPENDIX B to see other available alarm input/output details.
Chapter 5 5. Playback Overview Before continuing please be sure to have reviewed DVR Menu Setup (Chapter 3). You are now ready to begin setting up the DVR for playback. This chapter will show you how to setup the recorder for basic playback. 5.1 Basic Playback (1) Playback PLAY Press the PLAY key to start playing back the stored image/audio. The video start time depends on the quick play setting in the SYSTEM SETUP MENU. The DVR is duplex, which means you can record and playback the same time.
(3) Fast Forward/Reverse Playback Press the PLAY key to begin playing back process. PLAY Turn the Shuttle dial clockwise, to begin fast forward playback. The speed will be shown on the status bar of the bottom screen. >> 2, 4, 6, 8, 16, 32, 600X, and press ENTER at the same time to hold the play speed. The enter button will lock the X speed that is desired or you can manually hold the shuttle dial in the position. Press PLAY again to return normal play speed.
(5) Image advance Forward/Reverse Press PAUSE key to freeze the picture. PAUSE Turn the Jog dial clockwise to advance the still video image by image. Turn the Jog dial counterclockwise to rewind the still video image by image. The field feed speed will increase if the Jog dial is turned quickly.
5.2 Search Playback Press the SEARCH key to enter the SEARCH MENU. SEARCH In the SEARCH MENU, Dial the Jog clockwise or counterclockwise to change subentry values. Press the ENTER key to go next subentry in search menu setting, and press the CALL key to go last subentry in search menu setting. Press MENU to exit. Press SELECT or tilt wheel of the mouse to start search. Press SELECT to start search. (1) TIME / DATE Search Playback The following window will show up after pressing SEARCH key.
Note: If there is no video stored in the date/time specified, then the image will keep at the end of the last play, and the display time on the status bar shows “??:??”. 2(2) EVENT Search Playback You can change different event search methods if you select “BY EVENT” instead of “BY TIME / DATE”. 7 filters are ALARM, MOTION, VLOSS, A/M, A/V, M/V and A/M/V can be selected. The indications of events show as below.
The event types and number show on the second column of the search list. Where An: an Alarm event. the "n"th Alarm input. Dn: HDD overheated, overheat temperature is based on HDD temperature set in Warning Setup Menu. Fn: Fan fail, n = 1~3 fan number. LH: (Logical Head): Beginning of recording date & time right after HDD has been overwritten. LUn: Local User login record, n = 1~3, access level; where 1 is Administrator, 2 is Operator and 3 is General. Mn: a Motion event. n: the channel Number.
Chapter 6 6. Copying Video Before continuing please be sure to have reviewed the preceding chapters. You are now ready to copy an image or video from the DVR. This chapter will show you how to copy a still image or movie from the recorder. Insert the USB pocket driver into the USB slot on the front panel of the DVR to copy. USB slot: Digital Video Recorder allows users to select the camera for copying image (video) to movie file or copying DVRViewer, which is the image (video) player.
Diagram 6.1 In the COPY MENU, we define: 1. COPY Select Image (video) for copying images to movie file. Select Viewer for copying DVRViewer player. 2. DISK NO Disk number. It is changeable. 3. CAMERA NO: Camera channel number. You can select the video of camera you would like to copy. 4. START DATE & TIME: The start time of video you want to copy. END DATE & TIME: The end time of video you want to copy. 6. DEVICE The media you want to store the file. For D series, USB and DVD devices are available.
1 During playing back, press COPY button. (You will have a default bookmark ○ spanning 1 minute). For example, Start copy point is 10-10-2005 10:00:00 and end copy point will be 10-10-2005 10:01:00. 2 In live mode, press COPY button to enter the copy menu. In the Copy menu ○ choose image under the copy option. Then, press SELECT button to copy, you will see the START TIME has been changed to the “Bookmark time”. The end time is preset to 1 minute later. You can change it to another value if desired. 6.
Chapter 7 7. Call Overview This chapter will try to give you details on how to setup the CALL MENU on the DVR. Press the CALL key and the CALL MENU will pop up as below. Diagram 7.1 In CALL MENU, we define: 1. SEQ: Sequence display on the call monitor. Press SEQ to switch “ON” or “OFF” of the sequence status. 2. OSD: Channel name display on the call monitor. Press DISPLAY to switch “ON” or “OFF” of the OSD status. 3. CAMERA: The display camera in the call monitor. Press Channel NO to set display camera.
Chapter 8 8. Screen Display Setting & Mode In a full screen display, press SELECT key to pop up the display adjustment window as below: Diagram 8.1 In the screen display setting menu, we define: 1. CAMERA: The display setting of the current camera. 2. BRIGHTNESS: The brightness percentage of the current camera; from 0% to 100%. 3. CONTRAST: The contrast percentage of the current camera; from 0% to 100%. 4. COLOR: The color percentage of the current camera; from 0% to 100%. 5.
When turning SHARPNESS OFF, the image becomes blurred in an indoor environment. However, this option is suitable for outdoor use. If image flickers under a bright, outdoor environment, then the image can become mild by turning SHARPNESS OFF. The selected item will show in red color bar. Use Jog to increase or decrease the value. Press ENTER to confirm the setting value and move to next item. After finished setting, press SELECT or MENU key to save and exit the dialog.
8.1 Mode Button Press MODE to switch 4, 7, 9, 10, 13, 16 and PIP (picture in picture) displays for Live and Playback mode. (Note: PIP displays is not available in Playback mode). 9 displays: 9/16 CH. 7 displays: 9/16 CH. 10 displays: 16 CH. 4 displays: 4/9/16 CH. 13 displays: 16 CH. PIP: 4/9/16 CH. 16 displays: 16 CH.
Chapter 9 9. Upgrade Firmware This chapter will try to give you a detailed instruction on how to upgrade the DVR. This will be helpful in completing the upgrading process. 1. Copy the .ETW to your USB pocket drive from your computer 2. Insert the USB pocket drive in to the USB slot on the front panel of the DVR. When inserting the USB, make sure the direction of insertion is correct. 3. If you are in Record mode hit the stop button to stop recording first. 4.
Chapter 10 10. Networking Overview This chapter will try to give you a detailed instruction on how to network the DVR. Before we begin the process of networking your digital recorder we should have a working knowledge of what a network is and how it works. This will be a helpful in completing the networking process. 10.1 Introduction to TCP/IP TCP/IP is the suite of protocols used by the Internet and most LANs (Local Area Networks) throughout the world.
10.3 Gateway Address Each host in a LAN has a gateway. A gateway address is composed of four octets (numbers in the range of 0 to 255) separated by decimal points. The gateway address is used to uniquely identify a host or computer on the LAN which assigns the IP addresses to your network. For example, a Linksys router has an IP address of 192.168.1.1. If you were using this type of router within your LAN, then your gateway would be the IP address of the Linksys router.
10.5 Pre-Installation Before we begin with the installation we must ask ourselves a few questions in order to figure out where to begin with networking our DVR’s. Do you have Hi-speed Internet? ______________ There are many types of high speed Internet available. Three commonly used ones are T1, Cable, and DSL (in order of speed). Note: It is suggested to have a minimum upload speed of 256KBps. This can be addressed by the Internet Service Provider.
What type of DVR are you installing? ______________ Everfocus EDR series: EDR410, 810, 920, 1620 or 1640 Everfocus EDVR series: EDVR4F1, /EDVR4D1, EDVR9F1, EDVR9D1, EDVR16F1, EDVR16D1, EDVR16F2, EDVR16D2 or EDVR16D3. 10.6 What Type of Network Connection do you have? DVR’s can operate using three distinct types of networking connections. 1. Simple One to One Connection: A simple one to one connection is the most simple network connection.
10.7 Simple One to One Connection Cat 5 Cross-over-cable Crossover Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a cross over cable. Diagram 10.1 Connection Procedure: 1. The First step is to purchase or make a cross over cable. We recommend purchasing one if you have never made a cross over cable. Please remember you can not use a straight through network cable for this application 2.
4. Assign an IP address of 192.168.001.003 to the DVR, a Subnet mask of 255.255.255.000, and a default gateway of 192.168.001.001. 5. The next step is to get the computer onto the same network to do this you will need administrator access to your windows machine. 6. To assign a static IP address in windows 2000/XP.
92
93
94
7. Once you have reached this point click ok and restart both the computer and the digital recorder. 8. To access the DVR from the computer simply open Internet Explorer and in the address bar type: http://192.168.1.
10.8 Direct High Speed Modem Connection Hi-speed modem Internet Cat 5 Straight Through Cable DVR Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Diagram 10.2 Connection Procedure: 1. The First step is to purchase or make a straight through cable. We recommend purchasing one if you have never made a straight through cable. Please remember you can not use a cross over network cable for this application 2.
3. Now Log into the DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. 4. Assign the Static IP address which you obtained from the internet service provider to the DVR, the Subnet mask from the internet service provider to the DVR, and the default gateway of the internet service provider. Note: If you have a dynamic IP address this type of connection will not work for you. You will need to purchase a router or ask your internet service provider for a static IP address.
10.9 Router or LAN Connection Hi-speed modem Internet Cat 5 Straight Through Cable Router DVR Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Diagram 10.
Connection Procedure: 1. The First step is to purchase or make a straight through cable. We recommend purchasing one if you have never made a straight through cable. Please remember you can not use a cross over network cable for this application 2. Once you have a straight through cable plug one end into the LAN port on the back of the recorder and the other into the router. 3. Now Log into the DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. 4.
Use the prior step to assign an IP address. For example, if you got the IP address from the computer of 192.168.002.101. Assign the DVR’s IP address as 192.168.002.050. Now Copy the subnet mask and default gateway information you got from the prior step off the computer to the DVR. Note: Make sure the modem is in bridge mode. If your Internet Service Provider is BellSouth you will have a modem/router. BellSouth provides a Westell modem that includes a built-in router.
6. To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// and the IP address of your internet service provider. Note: If your Internet service provider blocks port 80 you may use a different port to access the DVR through the DVR’s Network Menu Setup.
Chapter 11 11. Linksys Port Forwarding This chapter will cover a few simple configurations for the Linksys router. Please understand we do not support this product and will not give tech support on it. If you need Technical support on this router you must call Linksys. This Chapter is to offer some help to the installer and end user nothing more. To access the Web-based Utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in the Address field.
The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.) To forward a port, enter the information on each line for the criteria required.
Application - In this field, enter the name you wish to give the application. Each name can be up to 12 characters. Start/End - This is the port range. Enter the number that starts the port range under Start and the number that ends the range under End. Protocol - Enter the protocol used for this application, either TCP or UDP, or Both. IP Address - For each application, enter the IP Address of the PC running the specific application.
DVR 37260 to 37260 Both 192.168.1.50 Enable Note: If your Internet service provider blocks port 80 and you are using a different port to access the DVR through the DVR’s Network Menu Setup please open those specific ports in this section of the router. The following is the address you would type: http:// IP address of your internet service provider: 8100 Dynamic DNS The Router offers a Dynamic Domain Name System (DDNS) feature.
106
Chapter 12 12. D-Link Port Forwarding This chapter will cover a few simple configurations for the D-Link router. Please understand we do not support this product and will not give tech support on it. If you need Technical support on this router you must call D-Link. This Chapter is to offer some help to the installer and end user nothing more. 1. The next step is to open ports within your router. Go to Virtual Server in the router.
Example1: Protocol Type The protocol used for the virtual service. Public Port The port number on the WAN (Wide Area Network) side that will be used to access the virtual service. Private Port The port number of the service used by the Private IP computer. Schedule The schedule of time when the virtual service will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. If it is set to Time, select the time frame for the service to be enabled.
Virtual Server Select Enabled or Disabled Name Enter the name referencing the virtual service Private IP The server computer in the LAN (Local Area Network) that will be providing the virtual services. If you have a Web server that you wanted Internet users to access at all times, you would need to enable it. Web (HTTP) server is on LAN (Local Area Network) computer 192.168.0.50 HTTP uses port 80, TCP and UDP. Name: DVR Private IP: 192.168.0.
Dynamic DNS Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. This is a useful feature since many computers do not use a static IP address. 1. To setup Dynamic DNS simple go to Tools and the Misc. At the bottom of the screen you will be able to enable DynDNS. 2. Once you have enabled it enter the server address of DynDNS.org: members.dyndns.org 3. Then enter the hostname you created with DynDNS.org Example: company.homeip.net 4.
111
Chapter 13 13. DDNS This chapter will cover a few simple configurations for setting up DDNS. Please understand we do not support this product and will not give tech support on it. If you need Technical support on DDNS you must call Linksys or D-Link. This Chapter is to offer some help to the installer and end user nothing more. 13.1 Creating a DDNS Account 1. The first step is to open Internet Explorer and in the address bar type: http://www.dyndns.com 2. The next step is to register with dyndns.
5. The next step is to add a host name with an extension. Example: Company.homeip.net 6. The IP address should already be entered for you. All you have to do is click add host and you are done registering DDNS. 7. You may refer to the previous two chapters to set up DDNS within your router.
8. To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// The DDNS you created example company.homeip.
Chapter 14 14. Viewing through Internet Explorer 1. To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// (LAN or IP address of your internet service provider) 2. The digital video login page will appear on the screen similar to the one shown above. 3. User must enter a user name and password to access the recorder. You can find your user name and password in the Network setting menu of your DVR. 4. The Default user name and password are admin and 11111111.
If the above error message pops up when you connect to EDR for viewing from internet, you should change Internet Option of IE (browser) to enable ActiveX controls. Select Tools -> Internet Options… Please refer to the above steps for changing Security Options to Low.
18 19 7 8 11 17 9 20 12 13 10 14 15 16 2 1 4 3 6 5 The above diagram is the main screen display. The icons on the lower corner of the screen are mainly for control and configuration; those on the right corner are for status indication. If any icon is grayed, it means that the specific function is not accessible in the current mode. The followings are a brief description for each of the icons. 1. REV. PLAY: Reverse Video Playback. 2. STOP: Press this key to stop Video Playback. 3.
7. The system allows up to 2 ways to playback video, by EVENT LIST and Time. 8. Events to be searched: Alarm, Motion and Vloss. 9. All available events are shown in the list. Select the desired event and it will be highlighted. 10. Click on “Play” to playback selected video event. 11. Press “Update” to refresh the event list. 12. Current connection and playback status are shown along with date and time. 13. Full screen view. 14. Quad screen view. 15. Nine split screen view. 16. Sixteen split screen view.
14.1 Search 14.1.1 Search by TIME There are 3 ways to do search by time. Press Pick a date first. 1. Press the button of M for changing Month to be searched, D for day, h for hour, m for minute and s for second. The “-“ sign at the left-hand side is to decrease the value, whereas the “+” sign at the right-hand side is to increase the value. 2. Move the slide bar between the buttons to change Month, Day, Hour, Minute, and second to be searched.
14.1.2 Search by EVENT 1. Select Event Type from Alarm, Motion and Vloss. Note: Please keep at least one event type checked. 2. Press Update button to refresh the event list. 3. All events of the selected type will be displaying along with Date/Time, event type (represents by a capital letter), camera number (represents by a number), e.g. M02 is the motion event from camera 2. 4.
14.2 PTZ control 1. Select the PTZ camera from drop-down menu. 2. Select Action Mode. 4 options are available: Continuous, Step x10, Step x5 and Step x1. 3. Use Direction Arrows (up, down, left, right) to move/adjust the focus to your desired direction and angle. 4. Press Z+ for Zooming In or Z- for Zooming Out. 5. In Focus option, press Near to move the focus closer to the subject. Or you can move the focus farther from the subject by pressing Far. 6.
9. A/B Point Scan allows you to do tour between 2 points. Move to the first point by using direction arrows and press SET A. Then move to the second point by using direction arrows and press SET B. Press RUN to start A/B Point Scan.
14.3 Remote Archive To Archive files: 1. Select Disk No. 2. Start Time/End Time indicates the start and end time of the disk selected 3. Camera: Select the camera that you wish to archive files. 4. Start: Select the start time to be archived. 5. END: Select the end time to be archived. There are 3 ways to search either Start or End time to be archived. Press 123 first.
1) Press on the button of M for changing Month to be searched, D for day, h for hour, m for minute and s for second. The “-“ sign at the left-hand side is to decrease the value, whereas the “+” sign at the right-hand side is to increase the value. Press OK 2) Move the slide bar between the buttons to change Month, Day, Hour, Minute, and second to be searched. Move the slide bar to the left-hand side for increasing the value, or right-hand side for decreasing the value.
In order to read the archived EDR MPEG4 Files (.arv), you would need to download viewer: 1. Press Download DVRViewer button. 2. Select “Run” or “Save” the file.
3. Open the DVRViewer.exe for loading the archived EDR MPEG4 Files (.arv) Detailed explanation of DVRViewer is as follows: i. ii. iii. iv. v. vi. vii. viii. Load File: to load the archived EDR MPEG4 Files (.arv). Stop: to stop playing “.arv” file. Play: to play “.arv” file. <>: step forward of the playing file. Capture: to capture the playing image as “.jpg” file. Save to Avi: to save the archived EDR MPEG4 File as “.AVI” file.
Note: (1)The recording frame rate will be automatically calculated. It is suggested to use the calculated Recording Frame Rate, although it is possible to change this value. (2) If you wish to save the audio recorded, please select Audio ON, so that the audio can be transferred to AVI file. Otherwise, select Audio OFF, then the audio recorded will not be transferred to AVI file.
Appendix A Appendix A: Remote Control 128
Appendix B Appendix B: Alarm Board Configuration EDVR16D1/F1, EDVR16D2/F2, EDVR9D1/F1, EDVR4D1/F1 models: 129
EDVR16D3 model: D-SUB 25 pin female connector (DVR) P164D00100 Alarm extension board (HOST) DVR PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NAME GND ALMIN 1 ALMIN 2 ALMIN 3 ALMIN 4 ALMIN 5 ALMIN 6 ALMIN 7 ALMIN 8 ALMIN 9 ALMIN 10 ALMIN 11 ALMIN 12 ALMIN 13 ALMIN 14 ALMIN 15 ALMIN 16 GND GND ALM_NC1 ALM_NO
Appendix C Appendix C: RJ45 (RS485) Pin Assignment 131
Appendix D Appendix D: Lapse Mode Recording Table Resolution: 720 x 480 System storage: 250 GB Lower: Low: Average size Basic: per image Standard: High: Superior: Video Source Simple: Complex: 8.04KB 12.33KB 8.42KB 13.7KB 10.15KB 16.72KB 11.86KB 19.56KB 14.72KB 24.63KB 18.60KB 30.05KB Terms of Use The HDD size required in your DVR may vary from this calculated test result under some conditions.
EDVR16D1/16F1/9D1/9F1/4D1/4F1 model NTSC Unit: Hour PICTURE QUALITY Recording LOWER LOW BASIC STANDARD HIGH SUPERIOR Speed simple complex simple complex simple complex simple complex simple complex simple complex (IPS) 8.04 12.33 8.42 13.7 10.15 16.72 11.86 19.56 14.72 24.63 18.6 30.05 30 287.9 187.74 274.92 168.96 228.06 138.45 195.18 118.34 157.26 93.98 124.45 77.03 15 575.8 375.48 549.84 337.93 456.12 276.89 390.36 236.69 314.51 187.97 248.90 154.06 10 863.
EDVR16D2/ 16F2 model NTSC Unit: Hour PICTURE QUALITY Recording LOWER LOW BASIC STANDARD HIGH SUPERIOR Speed simple complex simple complex simple complex simple complex simple complex simple complex (IPS) 8.04 12.33 8.42 13.7 10.15 16.72 11.86 19.56 14.72 24.63 18.6 30.05 60 143.96 93.87 137.46 84.48 114.03 69.22 97.59 59.17 78.63 46.99 62.23 38.52 48 179.95 117.34 171.82 105.60 142.54 86.53 121.99 73.97 98.29 58.74 77.78 48.15 40 215.93 140.80 206.19 126.72 171.05 103.
EDVR16D3 model NTSC Unit: Hour PICTURE QUALITY Recording LOWER LOW BASIC STANDARD HIGH SUPERIOR Speed simple complex simple complex simple complex simple complex simple complex simple complex (IPS) 8.04 12.33 8.42 13.7 10.15 16.72 11.86 19.56 14.72 24.63 18.6 30.05 120 71.978 46.93 68.73 42.24 57.02 34.61 48.79 29.59 39.31 23.50 31.11 19.26 96 89.973 58.67 85.91 52.80 71.27 43.26 60.99 36.98 49.14 29.37 38.89 24.07 80 107.97 70.40 103.09 63.36 85.52 51.92 73.
Troubleshooting If you have difficulty operating your system, run through the following checklist to see if you can solve the problem. The DVR will not go into record mode? Make sure the HDD is locked in with the keys. Also check to make sure the hard drives are set to C.S. (Cable Select). A diagram located on the Hard Drive Label will show you how to set the drive to C.S. The DVR displays no picture? First question you should ask yourself is the equipment wired properly.
JavaVM. If you have a Dynamic IP address from your Internet Service Provider. Dynamic IP addresses can cause conflicts when trying to connect to DVR(s) on a high speed internet connection. With new router technology (DDNS), it allows you to overcome this problem. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own DVR, website, FTP server, or other server behind the Router.
EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw USA Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.everfocus.com USA N.Y. Office: 415 Oser Avenue Unit S Hauppauge, NY 11788 Tel: 631-436-5070 FAX: 631-436-5027 www.everfocus.
