EZN Plus Series Outdoor IR Bullet IP Camera Quick Installation Guide Copyright © EverFocus Electronics Corp, Release Date: October, 2012
EZN Plus Series 1. Overview The EZN Plus Series is a bullet type IP camera designed for outdoor use. The series comes in three models: EZN3160 Plus / 3260 Plus / 3340 Plus. Model Name Megapixel WDR EZN3160 Plus 1.3 MP Yes EZN3260 Plus 2 MP Yes EZN3340 Plus 3 MP No 1 2 3 4 5 6 8 7 9 No. Item Name Descriptions 1 TV-Out Connector Connects to a handheld test monitor for adjusting camera focus and zoom.
EZN Plus Series System Requirements Before installing, please check that your computer meets the following system requirements.
EZN Plus Series 3. Installation This installation guide provides the basic instructions on installing an EZN Plus bullet IP camera. For details, please refer to the User’s Manual in the software CD. 3.1 Mounting and Wiring Follow the steps below for mounting and wiring the camera. 1. Before screwing the camera to the wall, drill four holes on the wall according to the hole-positions on the supplied Quick-Mounting Ring.
EZN Plus Series b. If you want to wire the cables through the wall, feed the cables through the wall and then screw the camera base to the Quick-Mounting Ring. Camera Base Quick-Mounting Ring Cables 5. Connect the network, power and other cables of the camera to the related devices. Please refer to 2. 4-Pin Data Cable earlier in this Quick Installation Guide. 6. Optionally insert a micro SD / SDHC card into the card slot. Please refer to 3.
EZN Plus Series 3.2 Inserting a Micro SD Card You can optionally insert a micro SD card to the card slot on the camera module for recording videos. 1. Remove the Sunshield from the camera. Loosen the screw on the Sunshield using the provided hexagon wrench. Slide the Sunshield out from the rail on the camera body. Sunshield Screw Camera Body 2. Unscrew the Fix Screw using the provided torx wrench and then remove the Lock Tab. Lock Tab Fix Screw 3. Rotate and then remove the camera cover. 4.
EZN Plus Series 3.3 Adjusting Camera Focus / Zoom After wiring the cables, you can adjust the camera focus and zoom for better image quality. 1. Follow Steps 1 ~ 3 in 3.2 Inserting a Micro SD Card to remove the camera cover. 2. Connect the power cable of the camera to the power source. 3. Connect a handheld test monitor to the TV-out connector for setting image zoom and focus. 4. To adjust camera focus, push the Focus / Zoom Control to the left or right.
EZN Plus Series 4. Accessing the Camera You have to assign an IP address for your camera to be accessible. To assign an IP address to the camera, use the IP Utility (IPU) software included in the software CD. Please connect the camera in the same LAN of your computer. 1. Install and then start the IPU program . The following dialog box appears. 2. Click Find Devices to search the cameras connected in the LAN. The default network values of the cameras will be displayed.
EZN Plus Series You can also change the other settings by double-clicking the values. After configuring the values, click Save Configuration. Note: Most networks uses DHCP to assign IP address, if you are unsure of your network settings, please consult your network administrators for configuration details. 6. To access the camera, highlight the camera and click Connect to Selected IP. The Internet Explorer window pops up. 7. Type the user ID and password to log in.
EZN Plus Series 5. Network Connections You can use one of the methods below to connect the camera to the network. Router or LAN Connection This is the most common connection in which the IP camera is connected to a router and allows multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you can remotely access the cameras from outside of the LAN via the Internet.
EZN Plus Series Direct High-Speed Connection In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”, where xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may require that you use DDNS for a reliable connection.
EZN Plus Series 6. Upgrading Firmware You can upgrade camera’s firmware using the IP Utility software included in the software CD. 1. Follow Step 1 to Step 4 in 4. Accessing the Camera to log in the camera. 2. Select the camera and then click Upgrade Firmware. A browsing window appears. 3. Select the firmware file (.evb) and then click Open. The IP Utility will automatically upgrade the firmware. The camera will reboot once the update is complete.
EverFocus Electronics Corp. EverFocus Taiwan: EverFocus Europe - Germany: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.
