Technical data

EKB500_ma_en_rev1.5_3.doc 34
Speed:___[1-239]
[ENT] to start.
7.6.2.4 Autopan
End stop definition
Define both the end stops and the autopan speed in the speed dome’s on-screen display. For further
details, please refer to the manual of the respective model.
Start A-B autopan
A
A
A
.
.
.
P
P
P
A
A
A
N
N
N
> enter pan speed
1
1
1
~
~
~
2
2
2
3
3
3
9
9
9
(any input, value is irrelevant due to speed being defined
in the dome menu) >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
7.6.2.5 Preset tour / Pattern
Define patterns (stored motion sequences of 30 seconds each) in the speed dome’s on-screen display.
For further details, please refer to the manual of the respective model.
Activate pattern
T
T
T
O
O
O
U
U
U
R
R
R
> enter pattern number 1~3 >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Activate Preset Tour
T
T
T
O
O
O
U
U
U
R
R
R
> 0 >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
7.6.3 Pelco-D / -P protocol compatible devices’ operation
Required protocol type in "COM PORT SETTINGS": Pelco-D / Pelco-P (according to dome / receiver)
Implemented protocol is based and tested with Spectra IIITM series halfduplex RS-485.
Third party domes with implemented Pelco-D protocol may have different features and
ATTENTION: Some Pelco-D / -P protocol domes and receivers require an address offset of -1 at the
keyboard, i.e. the address assigned to the dome / receiver in the EKB 500 menu must be 1 below the
address set in the dome / receiver itself!
7.6.3.1 On-screen display
Start menu:
M
M
M
E
E
E
N
N
N
U
U
U
or
P
P
P
R
R
R
E
E
E
S
S
S
E
E
E
T
T
T
>
9
9
9
5
5
5
>
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Switch between the settings:
S
S
S
H
H
H
I
I
I
F
F
F
T
T
T
(hold) +
J
J
J
O
O
O
Y
Y
Y
S
S
S
T
T
T
I
I
I
C
C
C
K
K
K
Change the settings:
I
I
I
R
R
R
I
I
I
S
S
S
+
+
+
Leave the menu: EXIT entry in OSD menu, confirm with
I
I
I
R
R
R
I
I
I
S
S
S
+
+
+
alternative:
M
M
M
E
E
E
N
N
N
U
U
U
or
P
P
P
R
R
R
E
E
E
S
S
S
E
E
E
T
T
T
>
9
9
9
5
5
5
>
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
For exit of some sub-menus the key
I
I
I
R
R
R
I
I
I
S
S
S
-
-
-
is used.
Camera:0001
Run Tour:__[1-16]