Installation & Operation Manual ENVS800 / ENVS1600 / ENVS3200 Nevio Network Video Servers
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Safety Precautions To avoid any damage, please consider the following safety warnings: • Never place the recorder near heaters, furnaces, other heat sources or in direct sunlight. • Operate the device only in locations maintaining the specified operating temperature range 0°C~40°C/32°F ~ +104°F, with moderate relative humidity. • Make sure that the device‘s ventilation slots are not covered or obstructed.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual This Product is RoHS compliant. WEEE Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling centre.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual CONTENT 1 INTRODUCTION ........................................................................................................6 2 MAIN FEATURES ......................................................................................................6 3 SPECIFICATIONS .....................................................................................................6 3.1 3.2 3.3 3.4 4 HARDWARE INSTALLATION .............................................
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7 APPENDIX B: 3 GPP SETUP EXAMPLES ............................................................. 81 7.1 7.2 CONFIGURATION IN NVR ........................................................................................ 81 CONFIGURATION MOBILE PHONE ............................................................................. 82 7.2.1 7.2.2 BenQ-Siemens E81 ...................................................................................................
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 1 Introduction The NEVIO NVR network video recorders are designed for recording and managing IP video devices. Easy and intuitive operation, combined with intelligent search functions enable fast and efficient evaluation of video records. Compatibility with many IP cameras from many different manufacturers allows the installation of this NVR series in a wide range of security applications.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Video Export Network Interface Other Interfaces Alarm I/O Monitor Output Power Ambient Temperature Housing Dimension (W x H x D) Weight Functionality General / System Menu Language Support E-Map Monitor Output Bandwidth Monitor Database Management Live View Video Analytic PTZ Recording Recording Method Schedule Recording Rate Playback Multi-channel Playback Search Function Video Enhancement Video Export Video Backup Remote Access Remote Video Access Me
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 3.2 Supported Camera Models Supported IP Cameras / Video server Status: Version 3.3.6.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Panasonic BB-HCM100; BB-HCM110; BB-HCM311; BB-HCM331; BB-HCM371; BB-HCM381; BB-HCM403; BB-HCE481; BB-HCS301; BB-HCM-547; BB-HCM511; BB-HCM515; BB-HCM527; BB-HCM531; BB-HCM580; BB-HCM581; BB-HCM701; BB-HCM705; BB-HCM715A; BB-HCM735A; BL-C10; BL-C1; BL-C20; BL-C30; BL-C101A; BLC111; BL-C121A; BL-C131; BL-C140A; BL-C160; KX-HCM110; KX-HCM280A; WJ-NT304; WJ-NT314; WVNP1000; WV-NP1004; WV-NM100; WV-NP240; WV-NP244; WV-NP304; WV-NP472; WV-NP502; WV-NS202; WV-NS2
ENVS800 / ENVS1600 / ENVS3200 Installation Manual • • • • • • • • • Keyboard Mouse Power Cord Software Licence S/N Document NVR software installation package. Located on the PC desktop under folder \EverFocus NVR, if needed to modify/repair the NVR software Installation and Operation Manual PDF on PC desktop This Quick Start Guide Genuine Windows OS CD-ROM Genuine Windows Label with Product Key (on PC).
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4 Hardware installation 4.1. Front panel controls and connectors DL DVD Burner behind panel Power switch Reset button Power LED HDD LED USB Ports [4] Audio [Microphone, speaker] 4.2.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.3 Status LED Gigabit LAN port The LAN RJ45 socket has 2 integrated LED for status of the LAN connectivity: 4.4 System connections The NVR series is designed primarily for network recording on a Local Area Network (LAN). Performance while recording cameras which are connected with router/DSL lines via a WAN or the Internet will be highly dependent on network bandwidth and reliability.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5 System Setup 5.1 First Time System Start With factory default user settings the NVR will boot automatically and start the NVR software application without requiring Windows Login and Application login. The NVR should start immediately after power is applied. If necessary, push the front power switch to start the NVR. By default, the NVR application starts with administrator user rights level.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.3 Quick Start Setup This chapter describes the minimum installation steps to install IP-cameras for standard (continuous) recording. Note: This quick start setup is based on the premise that all IP cameras in the system are installed in the same network and IP-address range as the NVR. The default IP setting of the NVR is DHCP mode. If there is no DHCP host on the LAN, a static IP configuration must be assigned using Windows. 1.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 2. Open camera setup menu >CONFIG > SETTING > tab CAMERA: After selecting the tab CAMERA the screen shows camera setup with an empty camera list.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual The camera setup supports 2 methods to install cameras: +Search: Express setup for camera types, which support UPnP. (EverFocus Nevio IP camera series support UPnP). +Insert: Manual input of camera data for camera types, which have no UPnP support.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Default user name and password for an EverFocus NEVIO cameras is: User name (admin level): user1 Password: 11111111 After setting the desired cameras confirm with OK to add these cameras to the NVR camera list: 17 of 115
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Manual IP camera setup An alternative to the search function is to setup cameras, including IP settings, manually. Click the icon “+INSERT” to open the camera setting window: Enter Camera Name, IP parameters and user name / password. Under DEVICE select a listed vendor and camera model or use the AUTO DETECT function. Click OK save these settings.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual For changing frame rate and recording image quality, select a camera from the list and press the CAMERA SETTINGS button: The window shows the current camera settings. Possible values depend on the camera type. Change the setting to fit the recording system requirements and confirm with OK. It is also possible to adjust camera display settings; click on VIDEO PARAMETER: After adjusting the display parameters confirm with OK.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual On lower right side of camera setup screen are additional settings for On Screen Display information which will overlay the camera display: OSD on/off OSD of date / date adjustment OSD of time / time adjustment OSD camera number OSD camera name OSD font settings OSD bitrate of single camera Apply selection to all listed cameras When settings are complete, click APPLY ALL to confirm for the selected (checked) cameras, then confirm with OK in the CAMERA
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Recycle Range: interval (1h to 1 day), how often NVR checks to delete old records Keep Video: If checked, the NVR will delete video data after a defined time period. If not checked, the NVR will use the full HDD capacity to achieve the maximum recording time. If recording shall start automatically upon application start, mark the checkbox SCHEDULE RECORDING SYSTEM under START-UP. Confirm all settings with OK.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4 Detailed Setup Following chapters describe the setup options of the NVR in all details. 5.4.1 Setting - General open with > CONFIG > SETTING This menu defines general parameters, display and start-up behavior of the NVR.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Live streaming server: with this box checked, the streaming server for live view will be activated at NVR start Remote playback server: with this box checked, the streaming server for playback view will be activated at NVR start 3GGP server: with this box checked, the 3GPP/mobile phone server will be activated at NVR start Remote desktop server: with this box checked, the remote desktop server will be activated at NVR start Central management reserved serv
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Status Display - Display options for global status display (right side of main screen) Display options, displayed with activated checkbox • Current time • Current date • Free disk space (total for all recording drives) • IP camera bitrate (summarised input stream) • CPU Temperature (not supported) • CPU fan speed (not supported) • User defined text 1 (free editable) • User defined text 2 (free editable) Auto reboot With activated checkbox the system will re
ENVS800 / ENVS1600 / ENVS3200 Installation Manual After selecting the tab CAMERA the screen shows camera setup with an empty camera list. The camera setup supports 2 methods to install cameras: +Search: Express setup for camera types, which support UPnP. (EverFocus Nevio IP camera series support UPnP). +Insert: Manual input of camera data for camera types, which have no UPnP support.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Select a camera for installing and activate the checkbox at left side: Enter user name and password for this camera and if applicable the camera name.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Manual IP camera setup Alternative to the search function it is possible to setup cameras including IP settings manually. Click the button +INSERT to open the setup window: Enter IP parameter and user name / password. Under DEVICE select a listed vendor and camera model or use the AUTO DETECT function. Click OK to take over the settings.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual For changing frame rate and recording image quality select a camera from the list and press CAMERA SETTINGS button: The window shows current camera settings. Possible values depend on camera type. Change the setting to the recording system requirements and confirm with OK. Optional it is possible to adjust camera display setting, click on VIDEO PARAMETER: After adjusting the display parameters confirm with OK.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual On lower right side of camera setup screen are additional settings for On Screen Display overlay display: OSD on/off OSD of date / date adjustment OSD of time / time adjustment OSD camera number OSD camera name OSD font settings OSD bitrate of single camera Apply selection to all listed cameras If all settings are done, confirm with OK in CAMERA setup menu.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.3 Setting - I/O Device This menu defines parameters for digital inputs and outputs of connected IP devices. The functionality depends on connected IP - devices.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.4 Setting - PTZ - Config Camera list Communication settings PTZ parameter Tour settings Preset settings Camera list Available cameras in the system. Select one and activate checkbox for editing PTZ functions. Basic settings Select the device type from the drop-down menu.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.5 Setting - Hotline (communication settings) This menu provides communication settings for mail, FTP, modem and phone. These settings are mandatory for several alarm reactions in GUARD mode (Send Snapshot to FTP, Phone call, Send SMS, Send e-mail). E-mail Input the following information: server, sender’s E-mail address, E-mail’s subject title, and body content. You may click on the Send Test Mail button to test the settings.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.6 Setting - User Account The NVR recorders provide user right management with free assignable user rights for each user.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.7 Setting - Address book Contact person settings are required for GUARD mode event reactions "Phone call", "Send SMS" and "Send mail". Enter the required data. Already defined contact persons are listed in lower part of the window.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.8 Setting - Monitor display Monitor selection for Playback Available cameras List of cameras, displayed on selected screen Auto scan settings Layout for multiview type "N" Run Playback on Monitor Selection of monitor output 1 or 2 for playback window Primary / Secondary Use the arrow buttons in the middle to add / remove cameras from the list of selected monitor. Removed cameras will not be displayed at this monitor.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.4.9 Setting - Joystick The NVR series supports EKB-200 joysticks and other HID compatible USB Joysticks. If the system detected a joystick, NVR will show the setup options under the tab JOYSTICK. Without connected joystick the options are greyed and not active.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5 GUARD - live event / event action configuration The GUARD mode allows live monitoring with automatic event reactions, triggered by intelligent video analytics functions. For the settings click on GUARD in Main screen: The menu screen shows all installed systems in the left side list, which can be used as event source. For defining an event select a device from the list and open with right click > NEW the context menu.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual For system events: The setup options for the event types are described in following chapters 39 of 115
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.1 Signal lost event Indicates signal loss from this camera.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.2 General motion event The GENERAL MOTION event allows motion detection in free definable square detection areas. ADVANCED For defining a detection area draw a window by mouse in the video window. Confirm setting with "REGION1". You can add more detection areas by drawing in the video window and confirming by "REGION1".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Sensitivity Sensitivity of motion detection, moving slider to right increases sensitivity, moving to left decreases sensitivity. Interval Filter function for motion detection. If slider is moved to right, a longer movement period is needed to trigger alarm Start / Stop Simulation With START SIMULATION you can test, if current settings are correct. Detected motion areas are displayed in yellow, below the video window appears "Event detected".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.3 Foreign object event This event type creates an event if an unexpected object appears in a defined zone. Define detection zone Draw the detection zone by mouse in the video window and confirm wit "REGION1". You can also add and subtract areas, as described in detail under "GENERAL MOTION". Define object size Draw in the video window an area in the expected size of the object.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Sensitivity Sensitivity of detection, moving slider to right increases sensitivity, moving to left decreases sensitivity. Interval Filter function for detection. If slider is moved to right, a longer period of object appearing in detection zone is needed to trigger alarm. Start / Stop Simulation With START SIMULATION you can test, if current settings are correct. Detected objects are displayed in yellow, below the video window appears "Event detected".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.4 Missing object event The event type MISSING OBJECT allows to monitor automatically objects in the camera field of view. Removing of the object will trigger an event. Define detection zone Draw the detection zone by mouse in the video window and confirm wit "REGION1". You can also add and subtract areas, as described in detail under "GENERAL MOTION".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Interval Filter function for detection. If slider is moved to right, a longer period of object disappearing in detection zone is needed to trigger alarm. Start / Stop Simulation With START SIMULATION you can test, if current settings are correct. Detected movements are displayed in yellow, below the video window appears "Event detected". End the simulation mode with "STOP SIMULATION".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.5 Camera occlusion event Sensitivity Sensitivity of detection, moving slider to right increases sensitivity, moving to left decreases sensitivity. Interval Filter function for detection. If slider is moved to right, a longer period of camera occlusion is needed to trigger alarm. Ignore Lighting change With activated checkbox the event will not trigger, if a global light change (turn light on / off) appears in the camera picture.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual BASIC Options: Life Cycle Definition, how long the message is shown Activated Period Permanent (Always Activated) or scheduled function (daily time period) 48 of 115
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.1.6 Focus lost event Sensitivity Sensitivity of detection, moving slider to right increases sensitivity, moving to left decreases sensitivity. Interval Filter function for detection. If slider is moved to right, a longer period of unfocussed camera is needed to trigger alarm. Ignore Lighting change With activated checkbox the event will not trigger, if a global light change (turn light on / off) appears in the camera picture.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual BASIC Options: Life Cycle Definition, how long the message is shown Activated Period Permanent (Always Activated) or scheduled function (daily time period) 5.5.2 Event actions Each defined event can be assigned to one ore more event actions.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Available event actions are: The event actions are described in following chapters. 5.5.2.1 Event action: Play sound After selecting PLAY SOUND as event action and double click opens a window for selecting the sound file. Select a file and confirm with OPEN.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.2.2 Event action: Send E-mail After selecting SEND E-MAIL as event action and double click opens a window with a list of available contact persons (setup in > CONFIG > SETTING > ADDRESS BOOK required): Select a contact for E-Mail notification and confirm with OK. 5.5.2.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.2.4 Event action: PTZ preset go This event requires PTZ cameras with preset function in the system. After selecting PTZ PRESET GO as event action and double click opens a window for selecting the PTZ camera, preset position and event related parameters. Confirm the entered values with OK.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.2.5 Event action: Signal digital output This event action allows to switch a contact output of an installed IP-device. After selecting SIGNAL DIGITAL OUTPUT as event action and double click opens a window with all available digital output contacts in the system: Activated the checkbox at desired contact output and confirm with OK. 5.5.2.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.5.2.7 Event action: send top central server Reserved for future functions 5.5.2.8 Event action: Send snapshot to FTP In case of an event the system will send a snapshot to the defined FTP server. This event action requires FTP-server setup under >CONFIG > SETTING > HOTLINE > FTP. 5.5.2.9 Event action: Popup e-map on event This event type allows display of an event in e-map (automatic popup).
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.6 Schedule setup The NVR allows continuous, scheduled or event controled recording. The recording behaviour is defined in the SCHEDULE menu. Open the SCHEDULE menu from MAIN console: In factory setting the system will record all cameras in continuous mode.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.6.1 Setup new schedule manually Step 1 Step 2 Step 3 Step 4 Step 1 Left-click and draw the bar to the time table. The scheduled time will appear as a grey bar. Step 2 Click the Insert icon and add a new schedule in the Regular Mode, i.e. to record video during the time period you set with 30 FPS, Normal video quality, and Normal resolution. Step 3 Change the setting if wished by clicking on the Configure icon (See 3.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.6.2 Copy Schedule You may set up the schedule for each channel/camera by repeating the process above, or simply apply the setting of a single camera to all the others. Copy To 5.6.3 3.5 Week Mode Schedule the cameras for each day of the week differently. In addition, you may assign extra holidays under the Week Mode. Default Holiday Custom Week Mode Default Follow the same process to setup the schedule for every day in a week.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Adjust the Scheduled Setting: You can manually change the setting at any time after you insert or load a period of schedule. Option 1: Move the cursor to the Time Bar and change the length or move the bar sideway to change the start and end points.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.6.4 Conigure - Encoding Option Panel Select Event Panel Always Record Record on Event Record on Motion Pre-record/ Post-record Always Record Select this option to record the video at all time. Record on Event Select this option to obtain the Select Event panel. From the Smart Guard list, check the box of the camera(s) that you want to trigger the recording action. Click OK to complete the setting.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.7 E-Map The NVR series provides an e-map function, which allows to show location of installed IP Devices on maps or other graphics. In GUARD mode the map can popup automatically in case of an event and show the event location including preview of the event camera. For setup of e-map go to > START > E-MAP. List of installed IP devices Map - area Preview window for selected camera Additional info for map. Select "Edit mode".
ENVS800 / ENVS1600 / ENVS3200 Installation Manual For placing a camera or contact on the map drag an item from device list and drop on the map at desired location. After finalising the layout finish the edit mode by clicking on OPERATE MODE.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.8 COUNTING APPLICATION The integrated Counting Application allows to count the number of persons, cars or other objects in one or both directions. The counting results can be shown in the camera live view. For evaluation of counting results the NVR provides a log with diagrams for definable time periods. For setup go to > SETUP > COUNTING APPLICATION Define Detection Zones The counting application requires 2 detection zones in the camera picture.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Define Object Size Define the estimated object size by drawing in the video window. If necessary, the object size has to be adjusted again after running simulation (in case of no safe detection). Options 1 Way Counting: Application will count movements from REGION 1 to REGION 2 only. 2 Way Counting: Application counts movements in both directions Sensitivity: Runtime Adjust the detection sensitivity depending on the scenery.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual the camera. Start / Stop Simulation After setting the parameters the settings can be tested in simulation mode. Counting results are shown under RESULT in lower right corner.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.9 Network Services For remote access to the NVR system are Server - functionalities required. The functions are managed and defined under NETWORK SERVICE. For setup go to > CONFIG > NETWORK SERVICE. 5.9.1 Network service: Live Streaming This service allows connections from other client PCs to the NVR by "REMOTE LIVE VIEWER" application or web browser. MAIN The list in the middle shows currently existing live connections (empty in screenshot).
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Kill Client Stops remote connection to selected connection from the list Kill All Clients Disables all current connections OPTIONS NOTE: Changing Server options is only possible, if the service is stopped Port Network port for remote live view. All remote client PCs have to use this port for remote access. Maximum Connections Number of connections that are allowed to connect to your system.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Black / White List Remote live access to NVR can be filtered by a White List (selected IPs can access) or a Black List (selected IPs are blocked for access). White List Check the “Enable White List” box to activate the white list filter. Only IP from the white list is allowed to log in. Black List Check the “Enable Black List” box to activate the black list filter. IP from the black list will be blocked.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Performance This tab shows current network streaming performance for total system and for selected live connection. Total bit rate Individual Camera bit rate 5.9.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.9.2 Network Service: Remote Playback When starting the remote playback function of your computer, you allow remote users to log on to the specific computer and withdraw data files that are stored on it. As system administrator, you are able to monitor the accounts that log on in order to maintain the system efficiency.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual is 64, one account counts as one connection. User Default Web Server If checkbox is activated, clients will be able to watch playback video via Internet Explorer. The port for live streaming server is set to 80 by default. Save log Save log file to specific folder Black / White List Remote live access to NVR can be filtered by a White List (selected IPs can access) or a Black List (selected IPs are blocked for access).
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Performance This tab shows current network streaming performance for total system and for selected live connection. Total bit rate Individual Camera bit rate 5.9.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.9.3 Network Service: 3GPP Service When starting the 3GPP service function of your computer, you allow remote users to log on the 3GPP supported mobile phone and view cameras that are connected to it. See Appendix B for more details about 3GPP Service. Service Start / Stop By clicking on START the server function for 3GPP service is enabled.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.9.4 Network Service: Remote Desktop When starting the Remote Desktop option of your computer, you allow remote users to use Remote Desktop Tool to login and configuration system. See Appendix C to install and use this tool. Port Assign a port for Desktop tool to login and configure system. Disconnect idle client after (300~3600 sec): Auto disconnect the on-line user who idled more than defined period.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.9.5 Network Service: Central Management This functionality is reserved for future application.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6 Appendix A: DB TOOL The DB Tool Repair database files and Export configurations. NOTE : improper use of this DB Tool may cause lose of the recorded video data. Step 1: Execute DB Tool from program files. Step 1 Step 2: Enter the password of administrator to login.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6.1 Repair Database This page has three repair method, Modify Location, Verify Only, and Repair. For modify location propose: Playback system can recognize all recording video in the folders which list on Main Console > Config > Setting > General page. For some reason, user need use Playback system to open recording video beyond storage location setting. For this propose, user could follow below steps to modify location by DB tool.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Example of database modification: In certain case that when video data needs to be transfer from old PC to another new PC, user will need to perform the following procedure. 1. Manually copy all recorded video data from the default installation path or other userdefined storage path of the old PC. Recorded video data 2. Manually paste all recorded video data to the default installation path or other userdefined storage path of the new PC 3.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual The system will list all video locations in table, but if there are any omit, please use insert. Note: After inserting location, the system will show files count below table. to Step 4: Choose the method of “Verify Only”, and click “verify”. This method will only check the files without modify. Verify result will show how many files broken or missing. Step 5: Choose the method of “Repair(Complete)”, and click “Repair” to repair.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6.2 Export Configurations This tool allows to export the complete configuration to a file. Step 1: Press “Export”. Step 2: Select the location you want to Export and type the name of the configurations. Step 3: Press “Save” to start to import database.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7 Appendix B: 3 GPP setup examples How to setup 3GPP streaming connection (using BenQ-Siemens mobile phones) 7.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Step 2 : Select 3GPP Service, and then click Start Note: In the Option item, the port selected here is the same port from mobile handset 7.2 Configuration Mobile Phone 7.2.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual Step 2: Select Bookmarks Step 3: Add New Bookmark Step 4: Configure the Address setting as the following example. Ex: rtsp://61.216.97.69:554/media00.3gp 61.216.97.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7.2.2 BenQ P50 1. Connect GPRS 2. Download and install the [PLATFORM4] software. 3. Execute Main Console. 4.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5. Open [PLATFORM4], press the button framed by red into Option 6. [Open Url] enter the rtsp address of the camera (EX: rtsp://61.216.97.69/media00.3gp channel 1 EX: rtsp://61.216.97.69/media01.3gp channel 2 EX: rtsp://61.216.97.69/media02.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7. [Setting I]change the setting and press “OK” [Protocol] TCP [Buffer Size] 60 [Connection TimeOut] 103 [Data Recept. TimeOut] 100 [Deblocking Filter] check 8.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 8 Appendix C: Installation of Remote Desktop Tool Installation Step 1: Insert the Installation CD. Step 2: Please go to RemoteDesktopViewer directly and Run Setup.exe file. Start Remote Desktop Tool Step 1: Please point to Start > All Programs > NUUO Remote Desktop Viewer > Remote Desktop Viewer. Step 2: Please enter address, Port, Password of NVR system. Enable the option Use 8 bits colour level to show steadier screen.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 9. Appendix D – Online License Procedures Contents • • • • • • 9.1 9.1 Overview 9.2 Rationale 9.3 Activation o 9.3.1 Activate by inputting serial number (SN) 9.3.1.1 Online 9.3.1.2 Offline o 9.3.2 Activate by importing serial number (SN) files (txt format) 9.3.2.1 Online 9.3.2.2 Offline o 9.3.3 Activate from dongle 9.3.3.1 Online 9.3.3.2 Offline 9.4 Transfer (De-activation) o 9.4.1 Online transfer o 9.4.2 Offline transfer 9.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 9.2 Rationale Using online license can resolve several issues such as... No more DOA/RMA issues because of hardware failure: If something is wrong with your license, EverFocus can check the license status for you and have it fixed online. No more hardware compatibility issues: Online license is just a set of hexadecimal strings. No physical device can cause any hardware incompatibility.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.) MainConsole will be restarted if activated successfully. 9.3.1.2 Offline In many cases, machines are installed in an environment without internet access. You may choose offline activation for these cases. In these cases, you need another (temporary) PC with internet access which will act as a proxy to interact with the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 2.) Select “Off line” as Activate type. 3.) Input the “SN (Serial number)”, and then click on “Activate” button. 4.) When you click on activate, it will present a window to ask where you want to save the off line license files, please make a new folder, say offline license, to save these files then click on OK. Next, copy this folder to another PC which is connected to Internet.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.) From another PC which is connected to internet, in the folder “off line license” find a file named OffLineTool.exe and execute it, click “Activate” to send the request file to the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6.) When you click on activate, it will present a windows to ask where you want to save the “License file” (dll format). You must then copy this license file back onto the NVR computer.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7.) Go back to the NVR computer (which is not connected to internet) and open the “License Manager” Tool again. Select “Import license file”, choose the path to the license file, then click the “Activate” button to proceed.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 8.) Main Console will be restarted if license file is imported successfully. 9.3.2 Activate by importing serial number (SN) files (txt format) If you want to activate several serial numbers on one server, you can use this option to activate several sets of license file simultaneously to save time. 9.3.2.1 Online 1.) Open “License Manager” Tool. 2.) Select “On line” as Activate type. 3.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.) MainConsole will be restarted if activated successfully. 9.3.2.2 Offline In many cases, machines are installed in an environment without internet access. You may choose offline activation for these cases. In these cases, you need another (temporary) PC with internet access which will act as a proxy to interact with the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 2.) Select “Off line” as Activate type. 3.) Select “Import SN file”, choose a text file containing multiple serial numbers, and then click on“Activate” button. 4.) When you click on activate, it will present a window to ask where you want to save the off line license files, please make a new folder, say offline license, to save these files then click on OK. Next, copy this folder to another PC which is connected to Internet.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.) From another PC which is connected to internet, in the folder “off line license” find a file named OffLineTool.exe and execute it, click “Activate” to send the request file to the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6.) When you click on activate, it will present a windows to ask where you want to save the “License file” (dll format). You must then copy this license file back onto the NVR computer.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7.) Go back to the NVR computer (which is not connected to internet) and open the “License Manager” Tool again. Select “Import license file”, choose the path to the license file, then click the “Activate” button to proceed.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 8.) Main Console will restart if the license file is imported successfully. 9.3.3 Activate from dongle If you already have a dongle connected, you are able to activate the license by converting the physical dongle to a virtual serial number. 9.3.3.1 Online 1.) Open “License Manager” Tool. 2.) Select “On line” as Activate type. 3.) Select “activate from dongle.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.) Main Console will be restarted if activated successfully. • Note: After the conversion, that dongle will be invalid.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 9.3.3.2 Offline In many cases, machines are installed in an environment without internet access. You may choose offline activation for these cases. In these cases, you need another (temporary) PC with internet access which will act as a proxy to interact with the license server. You create and then copy (via USB drive, for example) a request file from the NVR machine to the proxy and use the proxy PC to forward that file to the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.) When you click on activate, it will present a window to ask where you want to save the off line license files, please make a new folder, say offline license, to save these files then click on OK. Next, copy this folder to another PC which is connected to Internet. 5.) On another PC which is connected to internet, in the folder you created, off line license, please find a file named OffLineTool.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6.) When you click on activate, it will present a windows to ask where you want to save the “License file” (dll format). You must then copy this license file back onto the NVR computer.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 106 of 115
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 7.) Go back to the NVR computer (which is not connected to internet) and open the “License Manager” Tool again. Select “Import license file”, choose the path to the license file, then click the “Activate” button to proceed.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 8.)Main Console will restart if the license file is imported successfully. • Note: After the conversion, the dongle will be invalid. 9.4 Transfer (De-activation) When you are migrating a system to a different PC, or re-installing a system, FIRST you need to make a transfer. Transfer means that you are invalidating the use on your current NVR and registering a new NVR with the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 3.) After transfer, serial numbers will become de-activated. 9.4.2 Offline transfer Before transferring serial numbers, we strongly recommend you transcribe the serial number so that you will not forget it when you need to re-activate. In many cases, NVR machines are installed in an environment without internet access. You may choose offline transfer for these cases. You must complete an offline transfer before you migrate your system. 1.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 4.) When clicking on transfer, it will present several messages and a window to ask you where you want to save the offline transfer tools, please make a new folder named ‘offline transfer’ to save these files then click on OK. Next, copy this folder to another PC which is connected to Internet.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 5.) On another PC which is connected to internet, in the folder you created, off line license, please find a file named OffLineTool.exe and execute it, click “Transfer” to send the request file to the license server.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 6. Check if transfer process is completed.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 9.5 The states of a serial number A serial number can be at various states. The table lists the states below. State Description Ready The serial number is available for registration. Activated The serial number has already been registered. Deleted The serial number is not available. Blocked The serial number has been activated more than 3 times and is prevented from being used. 9.6 FAQ 9.6.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 9.6.2 What if I lose my serial numbers? You should be able to keep records of your purchased serial numbers. If you do lose them, please contact your reseller or sales contact. 9.6.3 What if someone uses my serial numbers? If your serial number is already registered, no one else can use your code to activate their main console. Main console will issue a warning if they try to do so. 9.6.
ENVS800 / ENVS1600 / ENVS3200 Installation Manual 115 of 115 NVR_Inst_Rev02.