EPN3600 IP PTZ Speed Dome User’s Manual Copyright © EverFocus Electronics Corp, Release: July 2009
EPN3600 Product Name: EPN Series EverFocus Network Speed Dome FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation.
EPN3600 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notice -These limits are designed to provide reasonable protection.
EPN3600 body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently. Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperature within 0℃ ~ +40℃ / 32 ~ 104 and a humidity below 90%. The input power source for this appliance is 12 VDC & PoE.
EPN3600 TABLE OF CONTENTS 1. INTRODUCTION.................................................................................................7 1.1. FEATURE .....................................................................................................7 1.2 ACCESSING THE CAMERA MENU ..............................................................9 2. SETTING ............................................................................................................16 2.1 SYSTEM INFO.....................
EPN3600 2.4.2.3.2 OSD/AREAS ..............................................................................56 2.4.2.3.2.1 Areas ........................................................................................57 2.4.2.3.2.2 Directions.................................................................................59 2.4.2.3.2.3 Display .....................................................................................60 2.4.2.3.3 PRIVATE ZONES ........................................................
EPN3600 1. INTRODUCTION The innovative EPN Series from EverFocus is a high performance multi stream H.264 IP speed dome featuring intelligent auto tracking functions. EPN is built-in H.264/MPEG-4/MJPEG digital signal output at 4CIF image size with up to 30fps and H.264/MPEG-4/MJPEG multi stream output for simultaneous live monitoring and high resolution recording. EPN also supports smart auto tracking functions such as exclusive masking, pan/tilt limits, tracking on patrol and flexible resume functions.
EPN3600 z z z Excellent position accuracy to ±0.1 degree From super low [0.01°/sec] to high fast [360°/sec] pan/tilt speed IP66 rated housing for any-weather outdoor use z z z Maximum 192 preset positions available Support directional virtual compass for easy operation. Users can select any reference direction as North Point.
EPN3600 1.2 ACCESSING THE CAMERA MENU Step 1.Start an Internet Explorer browser. Step 2. Enter the IP address or host name of the camera in the Location/Address field of your Internet Explorer browser. (Please refer to EPN2700/3100/3600 Installation Guide for how to find the IP address) Step 3. Input “Username” and “Password”. Default Username is “user1” and default password is “11111111”. Step 4. Click “Login” button. Step 5.
EPN3600 ○2 Press button to display the "Live" page. Double click on the image to show a full screen display, double click again or press ESC to return normal display. ○3 Press button to enter Setting page. In Setting page, there are 8 sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event] and [System]. Please refer to “2 SETTING” for further information. ○4 Press button to close EPN2700/3100/3600 network page.
EPN3600 where the image file is saved can be specified in “Setting -> User’s Config”. Please refer to “2.2 USER CONFIG” for further information. Note: Record segment is limited to 1 min. If you need to do long time recording, please set schedule recording. For schedule recording info, please see “2.7 EVENT”. ○8 Snapshot Click Snapshot button to save a snapshot of the video image currently being displayed. The location where the snapshot data is saved can be specified in “Setting -> User’s Config”.
EPN3600 Figure 1-2 PTZ Control Window : Zoom in : Zoom out : Focus far Focus near : Iris + : Iris – Arrow buttons: Click on an arrow button to navigate in that direction. : stop current action. : User can select PTZ speed from High, Standard, Low and Minimum.
EPN3600 Preset button: Click this button first, and input a preset position number by clicking number key and then click “Go” button to move the camera to a preset location. Note: To use this function, user need to set preset location in advance. Please refer to 2.4.2.1.1 Set Preset” for setting details. Auto Pan button: Click this button first and input a preset auto pan No. by clicking number key (1 for AB Pan, 2 for Endless Pan) and then click “Go” button to run a preset auto pan.
EPN3600 button to run a preset tour with auto-tracking function ON. Number button, Go button and Clear button: - Click desire number button and it will show in the gray text area at left-down corner. - Click “Clear” button to clear the text area. - Click “Go” button to run a selected function. 1○2 PTZ Control – Navigation Mode Select this to browse in direction user pointing at. 1○3 PTZ Control – Click-n-Go Mode Select this and system will center the pointing location for browsing.
EPN3600 1○7 Alarm Manual Control – Reset Press “Reset Alarm” button to reset alarm output remotely. 1○8 Status Display Show the name of the camera whose settings currently being configured, current date/time and current frame rate. 1○9 Event signals Tracking Alarm Motion When an alarm or motion event is triggered, a signal icon will flash to alert user. The first icon is for alarm event and rest of the 5 icons are for motion event.
EPN3600 2. SETTING Click Setting button (see red marker in Figure 2-1) to enter the setting menu (see Figure 2-2). There are 9 sections in setup menu: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event], [System] and [EKB200]. Figure 2-1 Camera Menu- Setting 2.1 SYSTEM INFO System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab. See Figure 2-2. 2.1.
EPN3600 Figure 2-2 System Info - Information 2.1.2 Log Figure 2-3 System Info -Log System Log: Date/Time: display date and time of the log.
EPN3600 user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the newest 256 records. Click button to export system log into a “.txt” file and select the location where the exported log file will be saved to. 2.2 USER CONFIG Figure 2-4 User Config User can set configuration of live view here.
EPN3600 Position: Select the position where the text will be displayed from Upper Left / Lower Right / Lower Left. Click Apply to apply the setting changes or Reset to reset without saving the change. Date/Time Format Used in Text Select Date/Time Format from the following options: Time Format: 24 Hours or 12 Hours. Click Apply to apply the setting changes or Reset to reset without saving the change.
EPN3600 the change. Language Setting Language: Select the language to be displayed in web page. Default language is English. To add a new language not listed in the original configuration, click the Browse button to locate the new language file (.evb) and then click the Load button. Note: Upload a new language file will cause system reboot automatically. Please reconnect IP speed dome after reboot. Click Apply to apply the setting changes or Reset to reset without saving the change. 2.
EPN3600 2.3.1 Network Figure 2-5 Network Setting- Network The following information is required to configure the network settings. Contact your network administrator or your internet service provider to get the info. • IP Type • IP address • Subnet mask • Gateway (when using the gateway server/router) • Primary DNS, Secondary DNS (when using DNS) IP Type DHCP: do not assign DHCP server the same IP addresses used for the other network cameras and PCs whose IP address is unique.
EPN3600 Note: If PPPoE is used as IP type, IP Utility software will not be able to detect the device. IP address When DHCP is not used, user needs to manually enter the IP address of the camera. Do not enter the IP address already used for PC or other network cameras. Subnet Mask This field is used to set the netmask for your network so that the IP speed dome will be recognized within the network. Example: 255.255.255.000. When DHCP is selected, the DHCP server will assign this value automatically.
EPN3600 2.3.2 DDNS Figure 2-6 Network - DDNS DDNS setting When accessing the camera via the Internet from the network environment of which the global IP address is obtained using DHCP, the DDNS function is necessary. To use the DDNS function, it is necessary to connect to the dedicated DDNS server. We offer 4 DDNS server providers as follow: ○ www.everfocusddns.com ○ www.sitelutions.com ○ www.dyndns.com ○ www.no-ip.com Enable: Check the box to enable DDNS setting.
EPN3600 Click button to register or update DDNS account.” If you wish to get a domain name from other DDNS provider, it is necessary to configure Record ID, FQDN, Username and password and register in DDNS server. Refer to the DDNS web site for further information about the DDNS. Click Apply to apply the setting changes or Reset to reset without saving the change. 2.3.3 Bandwidth Figure 2-7 Network – Bandwidth Bandwidth Setting Max.
EPN3600 Click Apply to apply the setting changes or Reset to reset without saving the change. 2.3.4 SMTP/FTP Figure 2-8 Network – SMTP/FTP Set SMTP The settings relating to the mail server, used to send the e-mail notification from the camera to predefined addresses via SMTP, can be configured. SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails. SMTP Port: Enter the port number for SMTP. Default is 25.
EPN3600 Password: Input the password if the SMTP server requires authentication. Receiver Address: Input the e-mail address for receiving e-mail message when the EVENT is enabled and triggered. Please use “;” to separate addresses. Sender Address: Input sender’s e-mail address, so that receiver can recognize the sender when an event message is sent out. Send Test Mail: Click assigned address.
EPN3600 2.3.5 Network Alarm (reserved for PowerCon) Figure 2-9 Network – Network Alarm Set Network Alarm This function is reserved for PowerCon software, for the detailed setting please refer to PowerCon network alarm protocol. 2.4 VIDEO The settings relating to video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs: the [Multi-streaming] tab and the [Camera] tab.
EPN3600 2.4.1 Multi Streaming Figure 2-10 Video – Multi Streaming Stream Setting The system can output 3 video streams simultaneously. For each of them, user can set compression format, resolution, quality and frame rate individually. Stream 1 is always enabled for live view. Check “Enable” box to enable other streams. Format: Select encode format from H.264, MPEG4 and MJPEG.
EPN3600 Click Apply to apply the setting changes or Reset to reset without saving the change. Video Recording Setting User can set video recording by selecting from one of the enabled video streamings. This will allow user to view live images as well as to record video of the other video streaming. Video Stream: Select a video recording stream from any enabled stream(s). Video File format: Recording file will be saved as AVI or ARV, select which file format to be used.
EPN3600 2.4.2.1 POSITION SETTINGS 2.4.2.1.1 Set Preset User can click Program button to enter “Preset Position” window (See Figure 2-12) to set different positions for a camera. There are 10 preset positions can be set in one page and totally 20 pages for preset positions. How to preset a position: 2 1 3 4 5 Figure 2-12 Video – Camera – Preset Window 1. Select a desired Preset No from a desired page. 2. Use “Arrow” buttons to select a desired position.
EPN3600 3. Click “Set” button to save this selected position, or Click “Clear” button to clear this position. “Go” button allow user to see a preset position on screen. 4. User can set Title, Focus Mode and White Balance for each preset position. 5. Click “Apply” button to confirm setting in step 4. User can also click “Reset” button to reset three values set in step 4. Freeze Picture: Speed dome will stop at the previous position until the next position is reached.
EPN3600 ○2 ○1 ○3 ○4 ○5 ○6 ○7 ○8 ○9 1○0 1○1 1○2 1○3 1○4 Figure 2-13 Video – Camera –Auto Tracking Window How to set Auto Tracking Start point: 1. Checking “Auto Tracking Start Point” item at ○1 . 2. Select a desired start point by using “Arrow” buttons at ○2 to locate a desired position. User can also use “Zoom In/ OUT”, “Focus Far/Near”, “IRIS +/-“ buttons at ○2 to help locating a desired position in this step.
EPN3600 selected start point on screen. Set Pan/ Tilt Limits 1. Set Pan/ Tilt Limits by checking this item and clicking its Set button at ○4 to enter its setting window (Figure 2-14). See setting details below. Figure 2-14 Auto Tracking OSD a. Click and at ○2 to select Pan option. b. Click IRIS+ button, , to enter Pan Range Setting (see Figure 2-15). Figure 2-15 Pan Range Setting – Left Limit Setting c. Use arrows buttons and buttons to locate a desired left limit point. d.
EPN3600 Click IRIS-, button to return. Figure 2-16 Pan Range Setting – Right Limit Setting e. Use arrows buttons and buttons to locate a desired right limit point. f. Click IRIS+ button, to save and return, or Click IRIS-, button to return. g. If tracking start point is outside the limits, the screen will show “ START POS IS OUTSIDE LIMIT. SET START POS” (see below example screen) and user has to reset a start position between left and right limits. a. Click and b.
EPN3600 Figure 2-17 Tilt Range Setting – Down Limit Setting buttons at ○2 to locate a c. Use arrows buttons and desired down limit point. d. Click IRIS+ button, Click IRIS-, , to enter next window (see Figure 2-18) or button to return. Figure 2-18 Tilt Range Setting – Up Limit Setting e. Use arrows buttons and buttons to locate a desired up limit point. f. Click IRIS+ button, to save and return, or Click IRIS-, button to return. g.
EPN3600 a. Click and b. Click IRIS+ button, to select Clear Pan/ Clear Tilt option. , to clear the setting. Set tracking mask Checking this item at ○5 and click its Set button to enter its setting window (Figure 2-19). See setting details below. Figure 2-19 Tracking Mask Window a. Click and to select desired Mask number from 1 to 4. b. Click IRIS+ button, , to enter selected Tracking Mask Size window. See Figure 2-20.
EPN3600 Figure 2-20 Tracking Mask Size Window User can change the tracking mask size here by using arrow buttons: : press this button to increase the length of the mask. : press this button to decrease the length of the mask. : press these buttons to increase the width of the mask. : press these buttons to decrease the width of the mask. c. User can also change the tracking mask point by clicking IRISbutton, , to enter setting window of tracking mask point. See Figure 2-21.
EPN3600 User can use arrows buttons and desired tracking mask position, and click buttons to locate a / button to save and return to Tracking Mask Size Window d. After completing setting, click IRIS+ button, , to save and return to Tracking Mask Window. Your will see “Go” displayed behind this set mask. Example: e. User can click or . button to change the status of preset mask, including Go, Clear and Set. Examples: : Click IRIS+ button, , to go to this preset mask position.
EPN3600 Tracking Duration: User can set tracking duration at ○8 . Available setting range is 0~600 second. Selecting “0” will turn off tracking duration. When tracking duration is up, the system will go back to start point. Note: if user did not set up a start point or start point is disabled, the system will go back to tracking initial point instead of start point. 9: User can set tracking mode when the object is lost on screen here.
EPN3600 Set Object Size User can set desired tracking object size by click “Set” button at 1○2. Figure 2-22 shows the screen of object size setting. Figure 2-22 Set Object Size: Max/Min frame User can set sizes of MAX and MIN frames here and the system will only track object with size between MAX and MIN frames. a. Click IRIS- button, , to enter select MAX or MIN frame for modification. The selected frame will flash at this time. b.
EPN3600 also click “Reset” button to make options to default values.
EPN3600 2.4.2.2.2 Set Auto Pan User can click Program button right next to “Set Auto Pan” to enter “Auto Pan” window (See Figure 2-23) to configure auto pan options for a camera. How to set Auto Pan: 2 3 5 1 7 6 8 Figure 2-23 Video – Camera –Auto Pan Window 1. Select Endless Mode on or off. ON: enable endless mode. The speed dome will perform 360 degree endless auto-pan. OFF: disable endless mode. The speed dome will perform auto-pan between preset left and right positions.
EPN3600 If OFF is selected at this step, go to step 2. 2. Select a desired left position by using “Arrow” buttons to locate a desired position. User can also use “Zoom In/ OUT”, “Focus Far/Near”, “IRIS +/-“ buttons to help locating a desired position in this step. “PTZ Speed” option allows user to browse with different speeds, including High, Standard, Low and Minimum. This step needs to be done only when Endless Mode is off. 3. Click “Set” button right next to “Set Left Pos.
EPN3600 2.4.2.2.3 Set Tour User can click Program button right next to “Set Tour” to enter “Tour” window (See below) to configure preset tours for a camera. Max. 16 positions can be set for a tour and there are 16 tours for user to preset for a camera. Figure 2-24 Video – Camera –Tour Window Mode: Select from three modes: OFF/ Preset/ Pattern. Value: Enter Preset/Pattern No. Before selecting preset/Pattern mode, user needs to set a preset position/ pattern in advance.
EPN3600 exclusive for Preset mode here. Speed: Select tour speed from 1 ~255. This option is exclusive for Preset mode. 2.4.2.2.4 Set Pattern User can click Program button right next to “Set Pattern” to enter Pattern window (See Figure 2-25) to set a pattern for a camera. 3 1 2 Figure 2-25 Video – Camera –Pattern Window 1. Enter a number (1~4) in “Pattern No” field. 2. Click “Set” button to start recording a pattern. At this time, the live screen will show “Recording Tour ..90s”.
EPN3600 Figure 2-26 Video – Camera –Set Pattern - Recording Tour Seconds 3. Use “Arrow” buttons, “Zoom In/ OUT”, “Focus Far/Near”, “IRIS +/-“ buttons and “PT Speed” option to operate camera on a desired pattern 4. After completing pattern operations, click “Complete” button to save this pattern tour. At this time, the live screen will show “Saving Pattern….”. User can also click “Clear” button to clear a pattern or click “Go” to run and see a preset pattern on live screen.
EPN3600 2.4.2.3 PTZ OSD SETTINGS Use the buttons on the browser window to operate the "Camera OSD setting" from a PC. There are 4 entries about PTZ OSD Setting allowing user to configure, including Video Settings, OSD/Areas, Private Zones and Info. See Figure 2-27. General Operation Guide of PTZ OSD Setting Menu button: Click this button to display the main menu of PTZ OSD on live screen. See Figure 2-27 as a sample of the main menu.
EPN3600 ▼ button/ ▲ button: Click these buttons select desired entry. : Click this button to save the change and go back to previous page. : - When an entry has an enter sign (see red marker in below image)behind it. Click this button to enter sub-menu of this entry.
EPN3600 2.4.2.3.1 VIDEO SETTINGS There are 9 options in Video Settings: Exposure, Focus Mode, Digital Zoom, White Balance, Backlight, Day/Night, Color, Negative and Wide Dynamic Range. See Figure 2-28. 2.4.2.3.1.1 Exposure In Exposure menu, there is a sub-menu. Figure 2-28 Video Settings- Exposure Press ► button/ ◄ button to enter Exposure sub-menu. Figure 2-29 Video Settings- Exposure Menu There are 4 options in Exposure menu: EL. SHUTTER, SLOW SHUTTER, IRIS MODE, and AE SPEED.
EPN3600 EL.SHUTTER: Select electronic shutter mode from the options of the menu. There are AUTO, A.FLK ,1/1, 1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/180 , 1/250 , 1/1000 , 1/3000 and 1/10000 at NTSC model; and AUTO, A.FLK, 1/50, 1/150, 1/215, 1/1000, 1/2500 and 1/10000 at PAL model. AUTO: Auto electrical shutter A.FLK: Anti-Flicker. Camera will auto adjust the shutter to reduce the flicker caused by fluorescent light. 1/60 (NTSC) and 1/50 (PAL): default manual shutter.
EPN3600 2.4.2.3.1.2 Focus Mode Figure 2-30 Video Settings - Focus Mode In Focus mode, we define focus type from ONE PUSH, AUTO and Manual. ONE PUSH: Enable the one push trigger focus mode. The focus lens holds the same position until the next trigger command is received. This function prevents the wrong focus in dark. AUTO: Auto focus is enabled.
EPN3600 2.4.2.3.1.3 Digital Zoom Figure 2-31 Video Settings - Digital Zoom Enable or disable digital zoom. ON: Enable a digital zoom. OFF: Disable a digital zoom. 2.4.2.3.1.4 White Balance Figure 2-32 Video Settings - White Balance White Balance has the following modes: AUTO: in this mode the system computes the white balance value output using color information from the entire screen.
EPN3600 value using the color temperature radiating from a black subject based on a range of value from 3000 to 7500K. INDOOR: 3200 K Base mode. OUTDOOR: 5800 K Base mode. 2.4.2.3.1.5 Backlight Figure 2-33 Video Settings - Backlight This is the function of Back Light Compensation. When the background of subject is too bright, or when the subject is too dark due to shooting in AE mode, back light compensation will make the subject appear clearer. ON: Enable Back Light Compensation.
EPN3600 Figure 2-34 PTZ Video Settings - Day/Night Select from AUTO, DAY and NIGHT NIGHT: IR cut filter is always removed (ICR ON). DAY: IR cut filter is always attached (ICR OFF). AUTO: Auto Day/Night mode switch. The camera will automatically switch the settings needed for attaching or removing the IR cut filter. With a set level of darkness, the IR cut filter is automatically disabled (ICR ON), and the infrared sensitivity is increased.
EPN3600 2.4.2.3.1.7 Color Figure 2-36 Video Settings - Color In Color, we define the color of the image. Select from ON and OFF. ON: Color image OFF: B/W image 2.4.2.3.1.8 Negative Figure 2-37 Video Settings - Negative In Negative mode, it will switch ON/OFF the negative art image output. Select from ON and OFF.
EPN3600 2.4.2.3.1.9 Wide Dynamic Range Figure 2-38 Video Settings - Wide Dynamic Range In Wide Dynamic Range, we define wide dynamic range from ON and OFF. This function is effective when shooting images against the sun, or when shooting a very bright subject. ON: Enable wide dynamic range OFF: Disable wide dynamic range. Note: When the wide dynamic range is ON, some part of the image may appear solarized. This is normal for the wide dynamic range, and is not a camera malfunction. 2.4.2.3.
EPN3600 2.4.2.3.2.1 Areas In Areas menu, there is a sub-menu. Press ◄ button/ ► button to enter Areas sub-menu (see Figure 2-40). Figure 2-40 OSD/AREAS menu- Areas Sub-menu In zone menu, you can set a zone and name it. When the speed dome turns to the zone you set, it will display zone name on the screen (only if “OSD/AREAS->Display -> Zone” is set as “YES”). How to set a zone 1. Click ▼ button/ ▲ button to select desired zone number for modification and Click “Enter” after selecting.
EPN3600 Figure 2-41 Areas setting – Left Position Setting Window 5. Then the right position setting window shows (See Figure 2-42).User can select right position by directly controlling from the live screen. After select desired left position, press “Enter” to confirm. Figure 2-42 Areas setting – Right Position Setting Window 6. Figure 2-43 will appear and Range section (see red marker in Figure 2-43) will flash at this time. To save the change, click Cancel button to save and exit.
EPN3600 Figure 2-43 Areas setting 2.4.2.3.2.2 Directions In Directions, there is a sub-menu. Figure 2-44 OSD/AREAS menu- Directions Setting Window Click ◄ button/ ► button to enter Directions sub-menu.
EPN3600 Figure 2-45 Areas setting menu- Set North There are two options in Directions menu: Set North and Default North. Set North Click Enter button to enter set North window (See Figure 2-46). User can locate a north position by directly controlling from the live screen. After selecting desired position, click Enter button to save. Figure 2-46 Areas setting menu – Set North Position Window Default North Go to “DEFAULT NORTH” and click Enter button to set the north position as default north position.
EPN3600 Figure 2-47 OSD/AREAS menu- Display Setting Window Click ◄ button/ ► button to enter Display sub-menu. Figure 2-48 Directions Setting Menu 1. SHOW OSD ON: show OSD of Camera Title, Directions, Zones, Preset Title, Motion, Zoom, Fan and Camera Status. OFF: do not show OSD. 2 SEC: show OSD for 2 seconds. 5 SEC: show OSD for 5 seconds. 10 SEC: show OSD for 10 seconds. 2. DIRECTIONS YES: show directions. Press Enter to enter sub-menu (See Figure 2-49).
EPN3600 Show Directions: Available options are Auto, 1/1, A.FLK, 1/60. Show Azimuth: Available options are Auto, 1/1, A.FLK, 1/60. Figure 2-49 Directions – Option Yes- Sub-Menu NO: do not show directions 3. ZONES YES: show zones NO: do not show zones 4. PRESET TITLE YES: show preset title NO: do not show preset title 5. ZOOM YES: show zoom multiple when zoom in or zoom out. NO: do not show zoom multiple. 6. FAN YES: show fan indication when fan is enabled. NO: do not show fan indication. 7.
EPN3600 2.4.2.3.3 PRIVATE ZONES User can set a private zone with its position and size. When Private zone is set to on, the private zone will be blocked (black) for view. There are 8 private zones can be set in this system. Figure 2-50 Private Zone Menu How to set private zone: 1. Click ► button to select ON on a desired Private Zone No. Note: If selected Private Zone No. has been set, the black private zone will be showed on the screen at this step.
EPN3600 Figure 2-51 Private Zone – Position Setting Window 3. Locate a position for private zone by directly operating from the live screen. 4. Press Enter to save position and enter next window, Private Zone Size setting window (See Figure 2-52). A small and gray square area showing on center of the window is default private zone. Default Private Zone b Figure 2-52 Private Zone – Size Setting Window 5.
EPN3600 Click ▲ button to increase the length of the private zone. Click ▼ button to decrease the length of the private zone. Click ► button to increase the width of the private zone. Click ◄ button to decrease the width of the private zone. Note: Press Cancel button at this step and the system will go back to previous window, Private Zone Position setting window, for re-adjusting 6. Press Enter button to save the private zone setting. Zone color: select private zone area color.
EPN3600 Figure 2-55 PTZ OSD- Info Window 1. PRESET-CNT: Preset counter. This counter counts the preset movement, and 1 is counted when the speed dome runs to preset position. 2. X-CONT: X-axis counter. This counter counts the x axis movement, and 1 is counted when the speed dome pans 360°. 3. Y-CONT: Y-axis counter. This counter counts the y axis movement, and 1 is counted when the speed dome tilts 180°. 4. Click Cancel button to return to previous menu. 2.4.2.3.
EPN3600 Figure 2-56 Audio Audio Check Enable Audio box to enable audio function. Audio Input: Audio from an internal microphone or a line source can be connected to the Audio connector of EPN2700/3100/3600. The audio source can be selected from Internal Microphone, External Audio Input L and External Audio Input R. Audio Input Volume: Adjust the Audio Input Volume for the audio input devices connected to the camera if there are problems with the sound input being too low or high.
EPN3600 2.6 USER Figure 2-57 User User Information Administrator can set Account, Description, password, Authority level and Status for a user in user information. Maximum 10 users can be set for using the speed dome. There are three different authority levels: • Supervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menu and can determine the registration of all other users. However, administrator is not allowed to change supervisor’s account and password.
EPN3600 Press Apply to apply the setting changes or Reset to reset without saving the change. 2.7 EVENT An event in the camera is when an Event Type is activated and causes certain actions to be performed. The event type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event type.
EPN3600 2.7.1 Event The settings relating to event occurrences such as settings for the event occurrence, motion, alarm and time mask can be configured on this page. The "Event " page has 4 tabs: [Event] tab, the [Motion] tab, the [Alarm] tab and the [Time Mask] tab. Figure 2-58 Event- Event Tab button to add an event condition. Press To modify the event list, click on the event and it will be highlighted. Press button to modify the setting.
EPN3600 To change the priority of events, click on the event and it will be highlighted. Press or button to move between events. The event that has highest priority will be activated first. Press Apply to apply the setting changes or Reset to reset without saving the change. Example 1: Manual trigger-Upload to FTP This example describes how to set the camera to upload images to FTP when someone press Manual trigger button: 1. Click button in Event page. 2. Enter an event name for the event, e.g.
EPN3600 pre-and post alarm buffer setting, please refer to “Alarm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. For detail about Time Mask, please refer to “2.7.4 Time Mask”. 8. Click to save this event in event list. Example 2: Alarm input – Go to PTZ Preset with Auto-Tracking This example describes how to set the camera to go to PTZ preset and start auto tracking at the preset position when there is alarm input: 1. Click button in Event page. 2. Enter an event name for the event, e.
EPN3600 4. Select “Go to PTZ Preset” as action type. 5. Check “Enable This Event”. 6. Select “Always” for time mask. For detail about Time Mask, please refer to “2.7.4 Time Mask”. 7. Select preset No. for Detail about set Preset, please refer to “2.4.2.1.1 Set Preset”. 8. Check “Go To Preset With Auto Tracking”. 9. Click to save this event in event list.
EPN3600 2.7.2 Motion Figure 2-59 Event – Event Tab Motion Detection User can define the motion area to be detected by left clicking the mouse to draw lines. Every click is an end point of the line. When the detection area is formed, double click the mouse to have all the lines connected. To remove the selection, simply right click the mouse, the selected polygon will be deleted. Press to update the current image. Press to have the entire screen selected for motion detection.
EPN3600 Moreover, you can set the Sensitivity level for motion triggered by selecting from 1 (low), 2, 3, 4, 5, 6, 7, 8, 9 to 10 (high). 2.7.3 Alarm Figure 2-60 Event – Alarm Tab Alarm Output Setting Contact Type: Normal Close, Normal Open Duration Time: Select duration time of alarm output from 5 sec, 10 sec, 20 sec, 30 sec, 60 sec, 2 min, 3 min and 5 min. Press Apply to apply the setting changes or Reset to reset without saving the change.
EPN3600 immediately after the trigger. Input the desired length of post-trigger buffer time. It can be set up to 120 seconds. Press Apply to apply the setting changes or Reset to reset without saving the change. Re-trigger Filter Setting Re-trigger Filter: Set a re-trigger filter time, if another event is triggered during this time, this triggered event will be ignored. Press Apply to apply the setting changes or Reset to reset without saving the change. 2.7.
EPN3600 Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, Tue, Wed, Thu, Fri & Sat. Set the Start time and End time for time mask by clicking Up arrow or Down arrow. Or simply press for a full day of event action. button to remove a scheduled time period. Press An example on how to set weekend as time mask is as follows: 1. 2. 3. 4. Click from time mask setting. Enter Mask name, e.g. Weekend. Check “Sun” & “Sat” boxes.
EPN3600 Machine Name Setting Machine Name: Enter the name of the camera. The entered name will be displayed in the status display area. Press Apply to apply the setting changes or Reset to reset without saving the change. Set Time Zone Time Zone: Select a time zone according to the location where the camera is in use. Set Date/Time Manually Date: Click the calendar and pick the date. Press << to go previous year, < to go previous month, > to go next month and >> to go next year.
EPN3600 synchronization with the NTP server. Time Zone: Select a time zone according to the location where the camera is in use. Press Apply to apply the setting changes or Reset to reset without saving the change. 2.8.2 Daylight Saving Figure 2-63 System – Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving. Set the start time to daylight saving time.
EPN3600 time and “End” time when daylight saving starts. Set the end time of daylight saving time. Set the end week of daylight saving time: 1st / 2nd / 3rd / 4th / Last Set the end day of a week of daylight saving time: Sunday / Monday / Tuesday / Wednesday / Thursday / Friday / Saturday Set the end month of daylight saving time: January / February / March / April / May / June / July / August / September / October / November / December.
EPN3600 are: • IP setting • DDNS setting Default: The Default button should be used with caution. Pressing this button will return all of the camera's settings, including the IP address, to the factory default values. The camera will then have to be re-installed. Save/Load Configuration Server To take a backup of all of the configurations, press Save to save all configurations to a config. file.
EPN3600 2.9 EKB200 Figure 3-65 EKB200 setting EKB-200 is an IP surveillance keyboard controller powered by USB port. User needs to set related control for each EKB-200 key in this window (see Figure 3-65). In Action list window, there are 12 EKB-200 button mapping options (From Key No.1 to Key No.12) can be set. User can choose action and set value for each Key No. If the command requires a value, such as GoTo Preset [x] or Tour [x], user needs enter the number [x] in the field "Value".
EPN3600 Joystick IRIS- FOCUS NEAR IRIS+ FOCUS FAR ○3 ○4 Figure 3-66 EKB200 Panel There are 20 available Action options, including: 1. Set Preset: When the action of a key is set “Set Preset”, use joystick to select a position and press this key on KEB200 to save the position as Preset Point. 2. Goto Preset: When the action of a key is set “Goto Preset”, press this key on KEB200 and the system will go the Preset Point. 3.
EPN3600 8. Iris Close: When the action of a key is set “Iris Close”, press this key on KEB200 to do Iris close. 9. Run Autopan: When the action of a key is set “Autopan”, press this key on KEB200 to start autopan. 10. Stop Autopan: When the action of a key is set “Stop Autopan”, press this key on KEB200 to stop autopan. 11. OSD Menu On: When the action of a key is set “OSD Menu On”, press this key on KEB200 to display OSD Menu on the screen. 12.
EPN3600 3. SPECIFICATIONS Product Model EPN2700 (outdoor) EPN3100 (outdoor) EPN3600 (outdoor) EPN2700i (indoor) EPN3100i (indoor) EPN3600i (indoor) CAMERA 1/4” Sony Ex-View HAD 1/4" Sony CCD Pickup Device CCD NTSC or PAL Video Format Scanning System NTSC: 525 TV lines, 60 fields/sec; PAL: 625 TV lines, 50 fields/sec. Picture Elements 768 x 494 (NTSC) ; 752 x 582 (PAL) Horizontal Resolution Min.
EPN3600 One Push/Auto/Manual Focus Control Auto/Manual Iris Control Yes (Auto/DAY/NIGHT) True Day & Night Auto Gain Control Yes, (OFF ; ON) Backlight Comp.
EPN3600 16 preset positions Tour Point per Group 4 patterns with 90 sec long each Pattern NETWORK / INTERFACE 10Base-T/100Base-TX auto-negotiation, RJ-45 socket Interface HTTP, TCP / IP, FTP, SMTP, DHCP, DNS, DDNS, NTP Supported Protocols Min.
EPN3600 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, China Office: Hsi-Chi, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw Building,Shandgdi Information Industry Room 609, Technology Trade Base,Haidian District, Beijing,China 10085 TEL: +86-10-62973336/37/38/39 FAX: +86-10-62971423 www.everfocus.com.cn USA Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A.
