Speed Dome EPTZ1000 USER MANUAL th Date: Aug.
Table of Contents 1. EPTZ1000 OVERVIEW.....................................................1-3 1.1. Introduction .............................................................................................. 1-3 1.2. Feature ...................................................................................................... 1-4 1.2.1. Profile of EPTZ1000 .......................................................................... 1-4 1.2.2. EPTZ1000 Base Board.......................................
2.5.3. Corner mount .................................................................................. 2-20 2.5.4. Pole mount ...................................................................................... 2-20 2.5.5. Ceiling mount .................................................................................. 2-21 2.5.6. Embedded ceiling mount ............................................................... 2-21 3. EPTZ1000 CAMERA SETUP MENU..............................3-22 3.1.
1. EPTZ1000 OVERVIEW 1.1. Introduction EPTZ1000, an intelligent high-speed dome camera is ready to secure your property with its omni-directional and exact monitoring. An 18X optical and 12X digital zoom combining with a high-performance chip makes captured images clear and vivid. The other powerful camera functions EPTZ1000 equips with: ¾ PAL / NTSC image format suppose. ¾ Auto and fast focus increases the searching speed and precision. ¾ Auto Iris adjusts the monitoring image to the best brightness.
All of the features make the intelligent high-speed dome camera works for a wide range and demanding application such as banks, airports, stations, casinos, streets of cities, intelligent buildings, and etc. 1.2. Feature 1.2.1. Profile of EPTZ1000 Wall Mount Bracket M5 Bolt (Hex) x3 Base PCB board Control board Housing Connection Bus Power Cable Inner Housing BNC Cable M3 Bolt x3 Mechanical Part Bulb Camera Module RS485 Cable 1.2.2.
and JP3 are connectors for heater, and they can be switched. JP6 is a fan controller connector that turns on/off of the fan. The 3 cables are too short to be connected to a wrong connector when putting them back. RELAY JP5 Video + Video RS485 + RS485 - AC24 AC24 JP6 JP3 JP4 JP1 1.2.3. EPTZ1000 Control Board The PCB board with two dipswitches is the control board of EPTZ1000. The two switches are used to set address, protocol, Baud Rate, video format and terminator resistance.
1.3. EPTZ1000 Connection 110V AC 24V AC POWER 24V AC / 3.5 A Adapter BNC 1.0Vpp ¡ Ó0.
1.4. EPTZ1000 Quick Operation Guide (Work with EKB500) EPTZ1000 and EKB500 (Keyboard) can work together by using factory default setting. You just need to connect cables by the following steps: 1. Connect the RS485 cable to EPTZ1000 and a keyboard (EKB500). 2. Connect a video cable from EPTZ1000 to a monitor. 3. Connect the power to EPTZ1000 and a keyboard (EKB500). After the EPTZ1000 finishes the self-test mode, you can start to operate the EPTZ1000 via the keyboard.
2. EPTZ1000 INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall mount bracket, one power adapter and one tool packet in the package.
Note: The input AC voltage range of an adapter depends on different area. Please make sure the voltage range before installing. Video Cable A BNC cable is used for connecting EPTZ1000 to a DVR or a monitor. An amplifier may be needed if the video cable is too long. Control Cable Basically, EPTZ1000 uses a differential pair to connect to other devices by cascading. A cable that has low signal decline can be used as a control cable. Alarm Cable An alarm cable is not included in the packing list.
2.3.1. Address Setting The address code of the EPTZ1000 should be set to correspond properly with a control device to control multiple dome cameras. The address codes are made up by the dipswitch SW1 (8 bits) on the PCB board. The 8 bits dipswitch indicates the binary coded of the address, and there are 256 addresses can be selected (0 ~ 255, 28 = 256). It also means that there up to 256 dome cameras can cascade on the RS485 bus.
Switch Address ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3
Switch Address ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 ON 1 ON 1 ON 1 ON 1 ON 1 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4
2.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The factory default protocol is EVF-1. EVF - 1 SW2 ON 1 ON 2 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 Maching Resistance PELCO-P 2 3 3 PAL / NTSC 1 2 2 Baud Rate ON 1 ON 1 Protocol PELCO-D Notice: Please make sure the power is off before setting, and restart the EPTZ1000 to enable a new value after changing.
2.3.4. Video Format Setting The 6th bits of the SW2 on the PCB board are used to set the video format. The default video format depends on the factory setting. Please do not to change it. NTSC SW2 ON 1 ON 1 2 2 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 Maching Resistance 3 PAL / NTSC 2 Baud Rate ON 1 Protocol PAL Notice: Please make sure the power is off before setting, and restart the EPTZ1000 to enable a new value after changing. 2.3.5.
n ¡ Ø255 RS485 Keyboard DVR Control Unit CAM-0 CAM-1 CAM-n Ternimator Resistance ON Note: When the dome is out of control, or does not work under control well, try to switch the terminator resistance ON. Notice: Please make sure the power is off before setting, and restart the EPTZ1000 to enable a new value after changing.
2.4. Rack and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and should comply with all local regulations. Service personnel should expect potential problems such as surface strength, surface material, falling objects, outer breaches, building vibration or other similar conditions. 2. Check for all necessary materials, and ensure if the selected installation location is suitable for the EPTZ1000. 2.4.2.
2. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from the packing, and take off the PCB board (4 bolts on it.) inside the housing. Thread the cable through the top of the housing. Fix the housing on the wall mount bracket, and screw in 3 M5 bolts (Hex) on the top of the bracket with the attached Hex Allen wrench to fix the housing.
5. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in order to engage it with the base. Screw the two bolts on the base, and then connect and fix the connection bus to the PCB board on the mechanical part. Notice: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. 6. Remove the lens protection cover before installing the bulb.
Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start to operate the EPTZ1000. When turning on the power, EPTZ1000 will enter self-inspection mode, and carry out a self-testing program. After finishing self-inspection, you can start to operate the EPTZ1000. 2.5. Separately Sold Brackets 2.5.1. Wall mount The wall mount bracket is used for installing speed domes on the wall indoors or outdoors. 2.5.2.
2.5.3. Corner mount The corner mounts are used for installing a wall mount bracket to a corner of walls indoors or outdoors. There are two kinds of corner mounts which are 90° and 270° mounts available. 2.5.4. Pole mount The pole mount is used for installing a speed dome on the ceiling indoors or outdoors. The extension poles are available for the pole mount.
2.5.5. Ceiling mount The ceiling mount is used for installing a speed dome on the ceiling indoor. 2.5.6. Embedded ceiling mount The embedded ceiling mount is used for lodging a speed dome in the ceiling indoor.
3. EPTZ1000 CAMERA SETUP MENU In this section, setup and operation guide of EPTZ1000 will be introduced. There are 22 items of the setting menu. However, there is only one line on the line display, so using some combination keys to operate is necessary. 3.1.
3.1.1. Camera Setup Menu Press MENU to enter camera setup menu. Shift Joystick up/down to change subentries, and right/left to change the setting. 1. CAM ID The name assigned to the camera. 2. DZOOM Digital zoom enable or disable. ON: Enable a digital zoom. OFF: Disable a digital zoom. 3. FOCUS Focus type, auto focus and manual focus are available. AUTO: Auto focus is enabled. MAN: Manual focus is enabled. 4. IMG MIRROR Mirror image. ON: Enable a mirror image. OFF: Disable a mirror image. 5.
7. ICR Day/Night Mode auto switch. The speed dome will auto switch to night mode, and display in B&W (Black and White) mode to increase the resolution when the illumination is low. ON: Enable the ICR function. OFF: Disable the ICR function. 8. COLOR Color display. ON: Enable a color display. OFF: Disable a color display, and show a B&W display. 9. FREEZE Freeze the display. ON: To freeze a display. OFF: To disable a freeze status. 10. DISPLAY Display system information and status.
MAN: Manual white balance mode. 13. TITLE DISPLAY : Display the title. ON: Enable title display. OFF: Disable title display. 14. AUTO FLIP Flip the camera when it tilts to the 90° end. ON: Enable auto flip. OFF: Disable auto flip. 15. ALM-IN1 SET The status of input alarm 1. N.O.: Enable a normal open alarm input. N.C.: Enable a normal close alarm input. OFF: Disable alarm input. 16. ALM-IN2 SET The status of input alarm 2. N.O.: Enable a normal open alarm input. N.C.
N.O.: Enable a normal open alarm input. N.C.: Enable a normal close alarm input. OFF: Disable alarm input. 19. ALM-IN PRIO The priority of alarms. 1234: The alarm priority is 1>2>3>4. 2341: The alarm priority is 2>3>4>1. 3412: The alarm priority is 3>4>1>2. 4123: The alarm priority is 4>1>2>3. 20. ALM-OUT Alarm output. There is a built-in relay to offer an alarm output. ON: Enable alarm output. OFF: Disable alarm output. 21. LOAD DEFAULT Load default setting.
4. EPTZ1000 FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Counterclockwise to control speed dome. Use the control keys which are Zoom, Focus and IRIS function keys on the keyboard to zoom In/Out, focus N (near)/F (Far), or IRIS +/-. ¾ HOME Mode: The camera view will go back to the home position when there is no keyboard operation in a specific time. The home position and the specific time can be set by press Set + Home.
then press Shift + Position. The system will ask you to enter the preset position number (1~239), and then press Enter to save the position. There are up to 192 positions can be preset. ¾ Set the parameter of a preset position: Press Set + Position to set the parameter of a preset position. You can set the going-to speed (1~239), dwell time (1~239 seconds), and the title of the position. Shift the joystick Right/Left to change bits, and shift the Joystick Up/Down to change the alphanumeric characteristic.
Note: The difference between the One-way tour mode and To-and-fro tour mode is that the return modes are different. For example: There is a tour with 3 preset positions 1, 2 and 3. The camera runs 1→2→3→1→2→3 in the One-way tour mode, and 1→2→3→2→1 in the To-and-fro tour mode. 4.5. Alarm to Position/Tour Link EPTZ1000 have 4 alarm inputs that can be set to link to a position or a tour when an alarm is triggered. ¾ Set an alarm link: Press F1 to set an alarm link.
APPENDIX A: The Alarm I/O Connection There are 4 alarm inputs and 1 alarm output available. The alarm I/O connector that is marked as JP5 is a nine-pin connector. It is located on the PCB board of the housing. JP5 1 ~ 9 RELAY JP5 Video + Video RS485 + Pin # Function 1 Alarm Input 3 2 Ground 3 Alarm Input 2 4 Alarm Input 1 5 Ground 6 Alarm Input 0 7 Normal Open (N.O.) 8 Common (COM) 9 Normal Close (N.C.
EverFocus Electronics Corp. Head Office: China Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Room 609, Technology Trade Building, Hsi-Chih, Taipei, Taiwan Shandgdi Information Industry Base, TEL: +886-2-26982334 Haidian District, Beijing,China FAX: +886-2-26982380 TEL: +86-10-62971096 www.everfocus.com.tw FAX: +86-10-62971432 www.everfocus.com.cn USA Office: 1801 Highland Ave. Unit A Japan Office: Duarte, CA 91010, U.S.A. 1809 WBG MARIBU East 18F, TEL: +1-626-844-8888 2-6 Nakase.Mihama-ku.
