EZ180 High Resolution B/W Weatherproof Camera User’s Manual and Operation Instructions
Notice This manual is presented to the users of EZ180 by EverFocus Electronics Corp. With years of engineering researches, EverFocus has spared no effort to provide the high quality products to the worldwide users. For the policy of continual product improvement, EverFocus reserves the right to make changes to the product specifications and documentation without notice.
Table of Contents Safety Warning …………………………………………1 Introduction……………………………………………..2 Specification…………………………………………….3 Major Parts Names…..…………………………….…..4 Installation Instructions………………………….….…5 Settings………………………………………………….
Safety Warning 1. Handle the camera with care. Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to prevent any damages to it. Do not disassemble it or place it on an unstable base. 2. Do not install the camera near electric or magnetic fields. Installed the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio speakers because the magnetic fields generate from above devices will distort the video image. 3.
Introduction The EZ180 series offers great performance in 1/3”image format B/W CCD camera. The EZ180 is ideal for outdoor applications such as parking lots, gas stations or shopping malls. The sophisticated circuit design provides a heater that turns on at 10℃ for cold weather. The EZ180 will provide protection against the elements and provide an excellent quality picture. Main Features : High Resolution: 560 TV Lines. Two types of built-in vari-focal lens for versatile applications.
Specification EZ180 Pickup Device 1/3” SONY B/W CCD Picture Elements 768 x 494 (EIA) 752 x 582 (CCIR) Horizontal Resolution 560 TV lines Video Output BNC 1.0Vp-p, 75 ohm Lens Focal Length Vari-focal lens f=3.5~8mm Vari-focal lens f=9~22mm *Lens models and availability vary in different regions Sensitivity 0.1 lux/F=1.6 Gamma Correction 0.45 S/N Ratio Over 48dB (AGC off) Back Light Comp.
Major Parts Names and Their Functions Back Fixing Plate Swivel Screw Sun Shield Cover Set-Screw Assembly Screw Mounting Base Fixing Screw Front Fixing Plate IRIS ALC/Level Adjustment Focus Zoom O-ring Seal Lens Heater Mounting Bracket Control Switch 4
Installation Instructions 1. Using the supplied screws, mount the bracket base on the desired location. 2. Connect the BNC connector of the camera to a monitor or other video device through a 75 ohm type coaxial cable with BNC female connector at cable extension. 3. Connect the 24VAC or 12VDC regulated power source of the camera (power jack) to the power-in jack with 2mm plug. For 12VDC power source, please make sure the power plug is center+ outerfor heater normal operation. 4.
g. When all the adjustments and settings are completed, overlaying the cover gently. Be careful not to damage to the “O”-Ring and camera components. h. To reassemble the sun shield, match the hole on the sun shield to the back fixing plate of camera, Fix the screw on the front fixing plate. Make sure the wider side of the fixing plate holds the edge of the camera well. 5. Attach the camera onto the mounting bracket. 6. Loosen the swivel screw and point the camera to the desired direction. 7.
Settings The camera is set up at factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. Please refer to the following description for the function details. The IRIS ALC and IRIS Level adjustments are located on the side circuit board, use a screwdriver to adjust if it’s necessary.
The 4 control switches are also located on the side circuit board, the switches in orders are for Flickerless, Back Light Comp, Auto Gain Control and Line Lock. FL Normal BLC Normal AGC Off LL Off On On On On Control Switches FL(Flickerless) Normal/On When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic shutter at 1/100(NTSC) or 1/120(PAL) automatically, and reduce the flicker immediately. The default setting is Normal.
AGC (Automatic Gain Control) Off/On AGC ON: The sensitivity increases automatically when light is low. AGC OFF: A-low-noise picture is obtained under a low light condition. The default setting is On. LL (Line-Lock) Off/On To select the sync mode between Internal Sync.(LL off) and Line-Lock (LL on). Set the line-lock off, the camera will synchronize to the internal time base. Set the line-lock on, the camera’s vertical synchronization can be driven by the AC signal in the power lines.
Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw Europe Office: Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany TEL: +49-2822-9394-0 FAX: +49-2822-939495 www.everfocus.de USA L.A. Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.everfocus.