EverFocus Installation / Operation Instructions EZ610 Low Light Inline IP66 Bullet Camera
EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0610001AR Operation Instruction © 2010 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. All rights reserved.
Precautions 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1 Product Overview..............................................................................................................................................7 1.1 Features ..........................................................................................................................................................7 1.2 Accessory Parts List ......................................................................................................................................
4 RS-485 Remote Control..................................................................................................................................30 4.1 Remote control with EKB-500 keyboard........................................................................................................30 4.1.1 RS - 485 Wiring ......................................................................................................................................30 4.1.2 OSD Menu Setting by Keyboard ..............
Chapter 1 PRODUCT OVERVIEW 1 Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus EZ610. Get color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions.
1.2 Accessory Parts List Please be careful when you unpack the box and the electronic device inside.
1.3 Specifications Model EZ610 Pickup Device Video Format 1/3" SONY Super HAD II CCD Picture Elements 768 x 494(NTSC)/ 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 (Sens-up 256x) S/N Ratio Electronic Shutter Video Output Over 52dB (AGC off) 1/50(1/60) ~1/100,000 Main Output BNC 1.0V p-p 75Ω, Local test output, cable provided. Gamma Correction 0.45 Lens Type DC Iris Varifocal: focal length 2.
1.
1.5 Camera Component Description Speedy-mount Ring Sunshield Use a coin or screwdriver to remove the cover Controls are inside the cover 1 2 3 4 Red: Menu mode Green: Lens mode 1) Reset: To load the factory default configuration press the button, which is inside this hole, for 3 seconds. Please gently insert a thin, non-metallic device into the hole to operate the reset button. 2) Control Key: For setting Lens & OSD menu.
Chapter 2 2 INSTALLATION This chapter will describe, in general terms, how to install the EZ610 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. 2.1 Wiring and Mounting Use the template and an appropriate tool to drill 4 holes to attach the speedy-mount ring.
Video & Power cables RS485 cable (optional) White: RS-485 + Black: RS-485 Power Socket RS-485 cable Connect the power and video cables. Attach the camera to the speedy-mount ring, securing it with the 4 screws provided. Optional Power and Video connection: Note: For details of RS-485 connection please consult chapter 4, for Rs-485 setup chapter 3.
2.2 Adjust Camera Position Adjust the viewing angle to the desired direction. With this unique 3-axis positioning system, installers can capture images from virtually any angle, without compromising. The camera can be adjusted in 3 ways.
3rd axis Loosen lock ring and set screw to rotate camera 360° Sunshield To remove or install the sunshield, use the hexagon wrench provided to loosen the screw at sunshield. Loosen this screw Slide rib on interior of sunshield into track on outside of camera body from front to back. Note: When properly installed, the rear of the sunshield is even with the rear of the camera body; improperly extending the sunshield to ‘shade’ the lens can compromise image quality.
Chapter 3 3 OSD MENU SETUP This chapter introduces how to change RS485 ID and Baud Rate and to configure the camera OSD menu. STEPS If you want to connect camera with keyboard or other RS-485 - controller, please refer to Section 3.2 RS485 ID & Baud Rate setting. Otherwise, please go to STEP 2. Configure the camera, as described below: 3.
NOTE: For those selected items with “ settings. ” sign in the end, there is a sub-menu for further Return to Previous Page Go to “Return” by turning the mini-joystick and press the mini-joystick to return to previous page. Close the Host Menu Screen To close the menu screen, navigate to the “EXIT” item and press the mini-joystick. 3.
3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets.
— Return — D-Effect — Mirror — H_MIR ; V_MIR ; OFF Gamma — 0.45~1.
3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press the SETUP button if you would like to return to the previous menu. 3.3.3 EXPOSURE 3.3.3.1 SHUTTER 1. 2. 3.
NOTE: 1. SENS-UP will be disabled, if AGC is OFF or the default SHUTTER value (1/50 PAL / 1/60 NTSC) was changed 2. The image becomes brighter when the setting increases; however, the after image increases as well. Due to the increased light sensitivity of the Super HAD II chip, far less DSP ‘boost’ is needed, resulting in color or B/W images in low light with minimal ghosting. 3. Please note that spots and noise may appear if light amplification increases when SENSE-UP is operating.
LEVEL Adjust the sensitivity level for HSBLC from 0 to 8. DEFAULT Set the factory default values for HSBLC. LEFT/RIGHT Set the Left/Right side of an area for the HSBLC to be adjusted. The value adjustable is 0~6. WIDTH Set the width of an area for the HSBLC to be adjusted. The value adjustable is 0~6. TOP/BOTTOM Set the Top/Bottom side of an area for the HSBLC to be adjusted. The value adjustable is 0~6. HEIGHT Set the height of an area for the HSBLC to be adjusted. The value adjustable is 0~6.
ATW Auto Tracking White Balance: This mode can be used within the color temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels). AWB Auto White Balance: This mode can be used within the color temperature range from 2,500°K to 10,000°K. (default) AWC ->SET To find the optimal setting for the current luminance environment in this mode, point the camera toward a sheet of white paper, and press “SET”.
Delay S-Level E-Level EXT auto switching function. Delay time for switch reaction on light changes, range 0~63 seconds. Trigger level for switching to day mode in range 0~100. Trigger level for switching to night mode in range 0~100. NOTE: The AUTO mode is not recommended for applications with highpower IR illumination. The camera may switch continuously between Day and Night mode.
3.3.7 SPECIAL In this section, user can do special settings including camera title, digital effects, motion, privacy zones, synchronization and language. Please direct the arrow to point to “SPECIAL” on the SETUP menu by using the UP and DOWN buttons. Select the mode you would like to operate by pressing the LEFT or RIGHT button. 3.3.7.1 CAM TITLE Input the camera title, and it will be appeared on the monitor. Please direct the arrow to point to “CAM TITLE” by using the UP or DOWN button.
3.3.7.2 D-EFFECT 3.3.7.3 FREEZE OFF ON Select “OFF” to view live image. Select “ON” to freeze and display current live image. 3.3.7.4 MIRROR OFF MIRROR V-FLIP ROTATE Disable digital effects. The image is displayed horizontal flipped. The image is displayed vertical flipped. Rotate the image 180˚. 3.3.7.5 D-ZOOM Setup for digital zoom. OFF ON Disable the D-ZOOM function D-Zoom: Select digital zoom from X1.0 up to X32. Note that zoom levels above X4 may lead to excessive pixellation.
3.3.7.8 RETURN Return: Press “RET” to save all settings in D-EFFECT menu and return to the previous menu. Press “END” to save all the menu settings and exit. 3.3.7.9 MOTION This camera enables you to observe movements of objects in 4 different areas on the screen, and the message “MOTION DETECTED” appears on the screen when movement is detected. The camera detects an object’s movement by sensing changes in the pixels displayed.
3.3.7.11 SYNC There are two SYNCHRONIZATION modes INTERNAL and LINE-LOCK. In LINE-LOCK mode, the video signal is synchronized to the frequency of the incoming AC power. The Line-Lock synchronization can only be used when the supply power is 24VAC 60Hz (NTSC models) or 50Hz (PAL models). INT L/L Internal synchronization Line-lock synchronization (only for 24 VAC) 3.3.7.12 LANGUAGE Select OSD language.
3.3.9 RESET 3.3.9.1 FACTORY RESET Reset to the default settings. Press “RET” to return to the previous menu. Press “END” to exit. 3.3.9.2 EXIT Save all the menu settings and exit. NOTE: If you quit a Menu without pressing EXIT, all the settings you previously modified will NOT be saved.
Chapter 4 RS-485 REMOTE CONTROL 4.1 Remote control with EKB-500 keyboard 4 4.1.1 RS - 485 Wiring For more details about RS-485 wiring please consult related chapters in EKB-500 user manual. Note! Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match the camera. (see COM port and CAMERA setting in EKB500 manual). EZ610 camera ID default is 01. Baud rate is 9600. Supported Protocols are EverFocus and Pelco-D.
SETUP 1. LENS 2. EXPOSURE 3. WHITE BAL. DC <┘ <┘ AWB d. Move the joystick RIGHT (f) and LEFT (e) to adjust the mode and parameters of the selected item. Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu” button when you finish all settings. For detail setting of each setup function, Please refer to “3.3. OSD Menu Setup”. 4.1.3 Lens Adjustment by Keyboard 1.
EverFocus Electronics Corp. Headquarters Office Beijing office 12F, No.79 Sec.1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan Tel: +886-2-26982334 Fax: +886-2-26982380 Room 609,Technology Trade Building.