EBD331e Indoor/Outdoor Mini Ball Camera 700TVL, 3-Axis, IP66, IR User’s Manual Copyright © EverFocus Electronics Corp, Release Date: August, 2012
CAUTIONS 1. Do not install the camera near electric or magnetic fields. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein. 3. Try to avoid facing the camera toward the sun. 4. Keep the power cable away from water and other liquids and never touch the power cord with wet hands. 5. Never install the camera in areas exposed to oil, gas or solvents. 6. Do not operate the camera beyond the specified temperature or humidity.
EBD331e 1. INTRODUCTION The EBD331e Ball camera is equipped with a 1/3” Sony 960H CCD image sensor providing resolution of 700 TVL. Featured with the Digital Wide Dynamic Range (D‐WDR) function, the camera can provide clear images even under back light circumstances where intensity of illumination can vary excessively. The EBD331e comes with 24 IR LEDs, supporting up to 15m (~50ft.) IR distance in night vision. The camera can work in both indoor and outdoor environments.
EBD331e 1.2 PACKAGE CONTENTS 1. EBD331e camera x 1 2. Mounting Template x 1 3. User Manual x 1 4. Accessory kit x 1 (4 Screws, 4 Anchors 5. Power Adapter Pigtail x 1 1.3 and one Hexagon Wrench) CABLE DEFINITIONS Cable Name Description Power Cable Connects to the 12V DC power source. You can optionally use the supplied Power Adapter Pigtail or a power adapter. Video‐Out Cable Connects to a DVR or a portable monitor for adjusting (BNC) camera angles. Power Adapter Pigtail 1.
EBD331e 2. SPECIFICATIONS Pickup Device 1/3" SONY 960H CCD Video Format NTSC or PAL (depends on model selected) Picture Elements 1020 x 508 (NTSC), 1020 x 596 (PAL) Horizontal Resolution 700 TVL Sensitivity 0.01 Lux / F=1.2; 0 Lux IR On S/N Ratio Over 48dB (AGC off) Electronic Shutter 1/50 (1/60) ~ 1/100,000 sec. Video Output BNC 1.0 Vp-p ,75ohm Gamma Correction 0.45 Lens Type Fixed Lens f=3.6mm / F=2.0 Auto Gain Control Yes White Balance Auto Sync. Mode Internal Sync.
EBD331e 3. INSTALLATION & OPERATION 1. Unscrew the Set Screw using the supplied Hexagon Wrench. 2. Unscrew the Outer Housing by twisting it counterclockwise and then remove the Outer Housing from the Camera Base. Outer Housing Camera Base 3. Paste the supplied mounting template onto a desired location on the ceiling / wall. Drill the four small holes for screwing the camera with the supplied Screws and Anchors, and the circle in the middle only if you wish to run the wires into the wall.
EBD331e 4. Insert the supplied 4 Anchors into the 4 holes on the ceiling / wall. 5. Screw the Camera Base to the ceiling / wall using the supplied 4 Screws. a. If you want to wire the cables from the side cut of the Camera Base, run the cables through the Camera Base first, attach and then screw the Camera Base to the ceiling / wall. b. If you want to wire the cables through the wall, attach and then screw the Camera Base to the ceiling / wall. Attach the Camera Body to the Camera Base. 6.
EBD331e EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe - Germany: Albert-Einstein-Strasse 1, D-46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.