Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 575nm 1206 21mcd 20mA

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 9

Device No:SZDSE-151-022 Prepared date: 19-Aug-2005 Prepared by: Meng Yali

Technical Data Sheet

1206 Package Chip LED (1.1 mm Height)

15-21SYGC/S530-XX/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain within RoHS complaint version.

Descriptions

․The 15-21 SMD Taping is much smaller

than lead frame type components, thus

enable smaller board size, higher

packingdensity, reduced storage space and

finally smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Part No.

Material Emitted Color

Lens Color

15-21SYGC/S530-XX/TR8 AlGaInP Brilliant Yellow Green Water Clear

Summary of content (9 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED (1.1 mm Height) 15-21SYGC/S530-XX/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Package Outline Dimensions 1.5 3.2 Note: Tolerances Unless Dimension is ±0.1mm , Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-151-022 http://www.everlight.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40~ +90 ℃ Electrostatic Discharge(HBM) ESD 2000 V Power Dissipation Pd 60 mW IF 60 mA Peak Forward Current (Duty 1/10 @1KHz) Soldering Temperature Reflow Soldering : 260 ℃ for 10 sec. Tsol Hand Soldering : 350 ℃ for 3 sec.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Typical Electro-Optical Characteristics VV Everlight Electronics Co., Ltd. Device No:SZDSE-151-022 http://www.everlight.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank xxxxxx xxxxxx RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned are ±0.1, Unit = mm. Everlight Electronics Co., Ltd. Device No:SZDSE-151-022 http://www.everlight.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: Tolerances Unless Dimension is ±0.1mm , Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-151-022 http://www.everlight.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ 5 sec. Test Sample Ac/Re Hours/Cycles Size 22 Pcs. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGC/S530-XX/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.