Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsSMD LED 575nm 1206 20mcd 20mA

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 1 of 9

Device No: SZDSE-151-018 Prepared date: 07-27-2005 Prepared by: sujiao Wen

Technical Data Sheet

1206 Package Chip LED (1.1 mm Height)

15-21SYGD/S530-E2/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․RoHS refer to SMD B type SGS report.

․The product itself will remain within RoHS compliant

version.

Descriptions

․The 15-21 SMD Taping is much smaller

than lead

frame type components, thus enable smaller

board size, higher packing density, reduced

storage space and finally smaller equipment

to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Automotive: backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

PART No.

Material Emitted Color

Lens Color

15-21SYGD/S530-E2/TR8 AlGaInP Super Yellow Green Green Diffused

Summary of content (9 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED (1.1 mm Height) 15-21SYGD/S530-E2/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․RoHS refer to SMD B type SGS report. ․The product itself will remain within RoHS compliant version.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No: SZDSE-151-018 http://www.everlight.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 ℃ for 3 sec.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No: SZDSE-151-018 http://www.everlight.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Everlight Electronics Co., Ltd. Device No: SZDSE-151-018 http://www.everlight.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No: SZDSE-151-018 http://www.everlight.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min.5 sec. Test Sample Ac/Re Hours/Cycles Size 22 Pcs. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 15-21SYGD/S530-E2/TR8 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd.