Datasheet

ManualsBrandsEverlight Electronics ManualsLEDsLED 650nm Red 3 mm T-1

www.everlight.com

LAMP

264-7SDRC/S530-A3

Features

• Choice of various viewing angles

• Available on tape and reel.

• Reliable and robust

• Pb free

• The product itself will remain within RoHS compliant version.

Description

•The series is specially designed for applications requiring higher brightness

•The led lamps are available with different colors, intensities..

Applications

• TV set

• Monitor

• Telephone

• Computer

Summary of content (7 pages)

PAGE 1
LAMP 264-7SDRC/S530-A3 Features • Choice of various viewing angles • Available on tape and reel. • Reliable and robust • Pb free • The product itself will remain within RoHS compliant version. Description •The series is specially designed for applications requiring higher brightness •The led lamps are available with different colors, intensities.. Applications • TV set • Monitor • Telephone • Computer 1 Copyright © 2010, Everlight All Rights Reserved. Release Date : Feb.02. 2013.
PAGE 2
DATASHEET LAMP 264-7SDRC/S530-A3 Device Selection Guide Chip Emitted Color Materials AlGaInP Resin Color Water Clear Deep Red Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Unit Continuous Forward Current IF 25 mA Peak Forward Current (Duty 1/10 @ 1KHZ) IFP 60 mA VR 5 V Pd 60 mW Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +100 Soldering Temperature Tsol Reverse Voltage Power Dissipation 260 ℃ for 5 sec.
PAGE 3
DATASHEET LAMP 264-7SDRC/S530-A3 Typical Electro-Optical Characteristics Curves ℃) ℃) Directivity (Ta=25 Radiation Angle Relative Intensity (a.u.) Relative Intensity vs. Wavelength (Ta=25 Wavelength (nm) Relative Intensity (a.u.) ℃) Forward Current vs. Forward Voltage (Ta=25 ℃) Relative Intensity vs. Forward Current (Ta=25 Forward Current (mA) Relative Intensity(a.u.) 1.5 1.0 0.5 0.0 0 Forward Voltage (V) 20 25 40 Forward Current (mA) Relative Intensity(a.u.
PAGE 4
DATASHEET LAMP 264-7SDRC/S530-A3 Package Dimension Note: Note: 1. All dimensions are in millimeters 2. The height of flange must be less than 1.5mm(0.059"). 3. Without special declared, the tolerance is ±0.25mm. 4 Copyright © 2010, Everlight All Rights Reserved. Release Date : Feb.02. 2013. Issue No: DLE-0006038_Rev.2 www.everlight.
PAGE 5
DATASHEET LAMP 264-7SDRC/S530-A3 Moisture Resistant Packing Materials Label Explanation CPN: Customer's Pb EVERLIGHT X Production Number P/N : Production Number QTY: Packing Quantity RoHS CAT: Ranks HUE: Dominant Wavelength 264-7SDRC/S530-A3 REF: Reference LOT No: Lot Number Packing Specification ■ Anti-electrostatic bag ■ Inner Carton ■ Outside Carton Pb EL ECTROSTATIC ELECTRONAGNETIC MAGNETICOR RADIOACTIVE RELDS anti-static for 750 ■ Packing Quantity 1.
PAGE 6
DATASHEET LAMP 264-7SDRC/S530-A3 Notes 1. Lead Forming During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. Lead forming should be done before soldering. Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it may break the LEDs. Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
PAGE 7
DATASHEET LAMP 264-7SDRC/S530-A3 Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest possible temperature is desirable for the LEDs. Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. 4. Cleaning When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. Dry at room temperature before use.