Datasheet

ManualsBrandsEVERLIGHT OPTO ManualsLEDs & AccessoriesSMD LED (multi-colour) Non-standard Red, Green 30 mcd, 16 mcd 120 ° 20 mA 2.1 V, 2 V 12-22SDRUGC/S530-A2/

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 1 of 10

Device No:DSE-122- Prepared date: 08-04-2004 Prepared by: Kenny Wang

Technical Data Sheet

Right Angle Lens Chip LEDs with Bi-Color(Multi-Color)

12-22SDRUGC/S530-A2/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Multi-color type.

․Pb-free.

Descriptions

․The 12-22 SMD Taping is much smaller

than lead frame type components, thus

enable smaller board size, higher packing

density, reduced storage space and finally

smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Automotive: backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Type Material Emitted Color

Lens Color

SDR AlGaInP Super Deep-Red

UG GaP Green

Water Clear

Summary of content (10 pages)

PAGE 1
EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Right Angle Lens Chip LEDs with Bi-Color(Multi-Color) 12-22SDRUGC/S530-A2/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free.
PAGE 2
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Package Outline Dimensions A 1.0 R G A 2.0 3.0 A C1 C2 (-) (-) (+) 1.0 Polarity For reflow soldering (propose) 3.5 0.9 1.5 Cathode mark 0.9 A 1.5 R0.44 0.65 A A Notes: Tolerances Unless Dimension ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.
PAGE 3
EVERLIGHT ELECTRONICS CO.,LTD.
PAGE 4
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Typical Electro-Optical Characteristics Curves SDR Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.
PAGE 5
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Typical Electro-Optical Characteristics Curves UG Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.
PAGE 6
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.
PAGE 7
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.
PAGE 8
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp.
PAGE 9
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.
PAGE 10
EVERLIGHT ELECTRONICS CO.,LTD. 12-22SDRUGC/S530-A2/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered.