Owner`s manual

ManualsBrandsEvermount ManualsTVs & monitorsEM-SA1000

www.everik.com SA1000.JO.042013.IM

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE! IF

YOU DO NOT UNDERSTAND THE INSTRUCTIONS, OR DO NOT FEEL THAT YOU CAN

FOLLOW THEM SAFELY, CONTACT A QUALIFIED CONTRACTOR. THE WARRANTY WILL BE

HONOURED IF ACCOMPANIED BY AN ORIGINAL SALES RECEIPT, AND ONLY IF THE

INSTRUCTIONS HAVE BEEN FOLLOWED EXACTLY. To acquire missing parts please visit

www.everik.com/en-CA/Parts-Request.html or call 1-866-604-6966.

• The EM-SA1000 is designed to mount a flat panel onto a vertical wall. Hardware for

mounting to a wood stud is included. For mounting to any other surface, it is recommended you

contact a qualified contractor.

• The wall or mounting surface must be capable of supporting the combined weight of the mount

and the flat panel, otherwise the structure must be reinforced.

• Safety gear and proper tools must be used. A minimum of two people are required for this

installation. Failure to use safety gear and/or attempting this installation alone can result in

property damage, serious injury, or death.

• Follow all instructions and recommendations regarding adequate ventilation and suitable locations

for mounting your flat panel. Consult the owner’s manual of your flat panel for more information.

• This product will hold flat panels up to 65” and weighing up to 100 lbs.

• VESA 600mm x 400mm

Tools Required

• Phillips head screwdriver

• Electric drill with 6mm bit (for studs) or 8mm bit (for concrete)

• Marking Pen or Pencil

• Hammer

• Stud finder

• Level

Instructions

Model:

EM-SA1000

Parts List

A B C D E

Countersunk Screw

M5x8mm

Cross Recess Head Screw

M5x8mm

M5x35mm

M6x35mm

M6x45mm

F G H I J

M8x35mm

M8x45mm

6mm Allen Key

ø12.7xø6x12.7

Plastic Spacer

ø19xø8.2x19.6

Plastic Spacer

Square Washer

Cable Tie

ø16xø8.2x2.0

Metal Washer

Wood Screw M8x65mm

Concrete Anchor

Summary of content (8 pages)

PAGE 1
Model: EM-SA1000 Instructions PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE! IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS, OR DO NOT FEEL THAT YOU CAN FOLLOW THEM SAFELY, CONTACT A QUALIFIED CONTRACTOR. THE WARRANTY WILL BE HONOURED IF ACCOMPANIED BY AN ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE BEEN FOLLOWED EXACTLY. To acquire missing parts please visit www.everik.com/en-CA/Parts-Request.html or call 1-866-604-6966.
PAGE 2
Step 1a - Wall mounting to a wood stud M8x65mm (6x) Step 1b - Mounting to a concrete wall M8x65mm (6x) Step 2 - Installing the monitor bracket A (6x) www.everik.com SA1000.JO.042013.
PAGE 3
Step 3 - Attaching the monitor bracket to the flat panel Flat back TVs Bump out or recessed back TVs I or J (4x) C, D, E, F, or G (4x) C, D, E, F, or G (4x) Note: You will have to hand test mounting screws and spacers to determine the correct combination for your flat panel. Step 4 - Mounting the flat panel B (2x) B (2x) Step 5 - Wire management www.everik.com SA1000.JO.042013.
PAGE 4
Positioning the wall mount Maintenance With a clean soft cloth, gently remove dust and other particles from the wall mount. If still not clean, please use a vitreous cleaner (non-nitrogen, non-alcoholic based) to remove dirt from the wall mount. Inspect all screws and hardware at regular intervals to ensure that no connections have become loose over time. Re-tighten joints as needed using the provided Allen Key (H). 6mm Allen Key (H) www.everik.com SA1000.JO.042013.
PAGE 5
Modèle: EM-SA1000 Instructions VEUILLEZ LIRE CES INSTRUCTIONS ATTENTIVEMENT ET LES GARDER POUR Y RÉFÉRER AU BESOIN. SI VOUS NE COMPRENEZ PAS LES INSTRUCTIONS OU SI VOUS NE CROYEZ PAS ÊTRE EN MESURE DE LES SUIVRE EN TOUTE SÉCURITÉ, VEUILLEZ COMMUNIQUER AVEC UN TECHNICIEN QUALIFIÉ. LA GARANTIE NE SERA HONORÉE QU'EN LA PRÉSENCE DU COUPON DE CAISSE ORIGINAL ET UNIQUEMENT SI LES INSTRUCTIONS ONT ÉTÉ SUIVIES À LA LETTRE. Pour obtenir des pièces manquantes, visitez www.everik.com/en-CA/Parts-Request.
PAGE 6
Étape 1a - Montage sur montant de bois Rondelle métallique Ø16*Ø8,2*2,0 (6x) M8x65 mm (6x) Étape 1b - Montage sur mur de béton Rondelle métallique Ø16*Ø8,2*2,0 (6x) M8x65 mm (6x) Étape 2 - Installation du support de moniteur A (6x) www.everik.com SA1000.JO.042013.
PAGE 7
Étape 3 - Fixation du support au moniteur TV avec dos plat TV avec dos incurvé ou concave Rondelle à plan carré I or J (4x) C, D, E, F, or G (4x) Rondelle à plan carré C, D, E, F, or G (4x) Remarque : Vous devez d'abord tester les vis de montage et les cales à la main pour déterminer la bonne combinaison pour votre moniteur. Étape 4 - Ajustement du moniteur B (2x) B (2x) Étape 5 - Rangement du câble Câble www.everik.com Attache pour câble (2x) SA1000.JO.042013.
PAGE 8
Positionnement du support mural Entretien Avec un chiffon doux et propre, retirez avec précaution la poussière et autres particules du support mural. S'il n'est toujours pas propre, utilisez un nettoyant à vitres (non-azoté et sans alcool) pour enlever la saleté du support mural. Vérifier toutes les vis et le matériel à intervalles réguliers afin de vous assurer qu'aucune connexion ne s'est relâchée avec le temps. Re-serrez les vis au besoin à l'aide de la clé Allen fournie (H). Clé Allen 6 mm (H) www.