User Manual

ManualsBrandsEverspring Industry ManualsElectronicsScrew-in On/Off Module

AD145-1

SCREW-IN ON/OFF MODULE

The AD145-1 Screw-in On/Off Module is a lamp holder (for Philips dimmable

LED bulbs only) and a transceiver which is a Z-Wave

enabled device.

Z-Wave

enabled devices displaying the Z-Wave

logo can also be used with

this unit regardless of the manufacturer. Inclusion of this Module on other

manufacturer’s Wireless Controller allows remote control of On/Off status.

Each Module is designed to act as a repeater. Repeaters will re-transmit the

RF signal to ensure that the signal is received by its intended destination by

routing the signal around obstacles and radio dead spots.

Adding to Z-Wave

Network

In the front casing, there is an On/Off knob coupled with LED indicator. The

knob is used as a Learn Key to carry out inclusion, exclusion or association.

When power is first applied, the LED flashes on and off alternately and

repeatedly at 2-second intervals. It implies that the unit has not been assigned

a node ID and cannot work with Z-Wave enabled devices. Please get familiar

with the terms below before starting the operations.

Function Description

Inclusion Add a Z-Wave enabled device (e.g. Lamp Holder) to Z-Wave network.

Exclusion Delete a Z-Wave enabled device (e.g. Lamp Holder) from the network.

Association After inclusion, you have to define the relationship between devices.

Through association, device can be assigned as master/slave, and specify

which slave is going to be controlled by which master.

Reset Restore the device to factory default settings.

The table below lists an operation summary of basic Z-Wave functions. Please

refer to the instructions for your Z-Wave

Certificated Primary Controller to

access the setup function, and to include/exclude/associate devices. The lamp

holder executes the function of auto inclusion when…

Auto Inclusion

1. The power is applied for the first time and no ID code has been stored in

the unit.

2. The execution of Exclusion or Reset is successful and the stored ID code is

cleared.

Note: The duration for Auto Inclusion is 4 minutes during which period the node

information of explorer frame will be emitted once every 5 seconds. Unlike the

“Inclusion” procedure described in the next section, the execution of Auto

Inclusion is automatic without the necessity of pressing the learn key.

Module Status and LED Indication

As soon as the light bulb is screwed into the lamp holder, the LED on the Module

will be flashing slowly. This implies that the Module is not yet included in a

Z-Wave system and cannot be controlled by the Wireless Controller. However,

pressing the On/Off knob will control directly the On/Off status of the connected

bulb without using the Wireless Controller.

The following table lists the module status and LED indications:

ction or

Status

Description LED Indication

Inclusion

1. First set the Controlle

into

Inclusion mode.

Press once and LED flashes once.

LED will flash 3 times when code

is emitted successfully.

2. Press the Learn Key on the

unit once.

Exclusion

1. First set the Controlle

into

Exclusion mode.

Press once and LED flashes once.

LED will flash 3 times when code

is emitted successfully.

2. Press the Learn Key on the

unit once.

Association

1. First set the Controlle

into

Association mode.

Press once and LED flashes once.

LED will flash 3 times when code

is emitted successfully.

2. Press the Learn Key on the

unit once.

E26/E27 lamp cap

ON/OFF KNOB

LED INDICATOR

E26 Lam

Summary of content (3 pages)

PAGE 1
The table below lists an operation summary of basic Z-Wave functions. Please refer to the instructions for your Z-WaveTM Certificated Primary Controller to access the setup function, and to include/exclude/associate devices. The lamp holder executes the function of auto inclusion when… AD145-1 SCREW-IN ON/OFF MODULE The AD145-1 Screw-in On/Off Module is a lamp holder (for Philips dimmable LED bulbs only) and a transceiver which is a Z-WaveTM enabled device.
PAGE 2
Reset 1. Press the Learn Key 5 times within 5 seconds. Operation 2. The Home ID and Node ID in the memory will be cleared and system will be restored to factory default. To turn on or off the bulb controlled by the Module: LED flashes 3 times. Empty No ID code memorized. On for 2 seconds & off for 2 seconds. Normal Normal operation mode. LED turns on/off according to the Module being on or off. z z z z Installation 1. Turn off the wall switch on the wall or mains power supply. 2.
PAGE 3
Troubleshooting Federal Communication Commission Interference Statement Symptom Cause of Failure The module not working and LED off 1. The module’s LED working, but the connected light bulb not working 1. 2. The receiver’s on/off knob can control on/off status, but the transmitter cannot control the receiver 1. Incorrect ID code 2. Transmitter’s battery runs low 3. Out of receiving range or poor reception 4.