User's Manual

ManualsBrandsEverspring Industry ManualsElectronicsMini-Magnetic sensor

HSM02 DOOR/WINDOW DETECTOR

The Door/Window Detector is a Z-Wave

enabled device and is fully compatible

with any Z-Wave

enabled network. Z-Wave

enabled devices displaying the

Z-Wave

logo can also be used with it regardless of the manufacturer, and ours

can also be used in other manufacturer’s Z-Wave

enabled networks. Inclusion

of this Door/Window Detector on other manufacturer’s Wireless Controller menu

allows remote turn-on of connected modules and their connected lighting when the

Detector is triggered.

LED

TEMPER

SWITCH

BATTERY

MYLAR

FIXED

SCREW

Include to or Exclude from a Z-Wave

Network

In the front casing, there is a tamper switch which is used to carry out inclusion,

exclusion or reset. When power is first applied, its LED flashes on and off

alternately and repeatedly at 2-second intervals. It implies that it has not been

assigned a node ID and cannot work with Z-Wave enabled devices. Please get

familiar with the terms below before starting the operations.

Function Description

Inclusion Add a Z-Wave enabled device (e.g. Detector) to Z-Wave network.

Exclusion Delete a Z-Wave enabled device (e.g. Detector) from the network.

Association After inclusion, you have to define the relationship between devices.

Trough association, device can be assigned as master/slave, and specify

which slave is going to be controlled by which master.

Reset Restore Detector to factory default.

The table below lists an operation summary of basic Z-Wave functions. Please

refer to the instructions for your Z-Wave

Certificated Primary Controller to access

the setup function, and to include/exclude/associate devices.

Function Description LED Indication

No node ID The Z-Wave Controller does not allocate

a node ID to the unit.

2-second on, 2-second

off

Inclusion 1. Have Z-Wave Controller entered

inclusion mode.

2. Pressing tamper switch three times

within 1.5 second will enter inclusion

mode.

Exclusion 1. Have Z-Wave Controller entered

exclusion mode.

LED lights up once

whenever tamper switch

is pressed once.

2. Pressing tamper switch three times

within 1.5 second will enter

exclusion mode.

Reset 1. Press tamper switch three times

within 1.5 second.

2. Within 1 second, press and hold the

tamper switch until LED is off.

LED keeps on before

reset function has been

completed.

3. IDs are excluded and all of preset

value will be reset to factory default.

2-second on, 2-second

off

Association 1. Have Z-Wave Controller entered

association mode.

2. When pressing tamper switch three

times within 1.5 second, the unit will

emit the NIF which implies that the

unit has entered association mode.

ÚIncluding a node ID allocated by Z-Wave Controller means inclusion. Excluding a node

ID allocated by Z-Wave Controller means exclusion.

ÚFailed or success in including/excluding the node ID can be viewed from the Z-Wave

Controller.

Summary of content (6 pages)

PAGE 1
HSM02 DOOR/WINDOW DETECTOR The table below lists an operation summary of basic Z-Wave functions. Please refer to the instructions for your Z-WaveTM Certificated Primary Controller to access the setup function, and to include/exclude/associate devices. The Door/Window Detector is a Z-WaveTM enabled device and is fully compatible with any Z-WaveTM enabled network.
PAGE 2
Choosing A Mounting Location 2. Using the adhesive tape to fit detector on the door or window. The Door/Window Detector is suitable for mounting in dry interior locations only. 3. Fit the magnet to the moving part of the door/window opposite the detector using the adhesive tape. Decide which doors/windows are to be protected by Door/Window Detectors, (usually the front and back doors as a minimum will have Door/Window Detectors fitted).
PAGE 3
4. When the tamper switch is pressed, the unit enters normal mode and the red indicator LED on the Detector will not illuminate to conserve battery life when the detector is triggered, (unless the battery power is low). Magnets to be opened: [Command Class Sensor Binary, Sensor Binary Report, Value = 0xFF(255)] Programming Magnets to be closed: [Command Class Sensor Binary, Sensor Binary Report, Value = 0x00(0)] 1.
PAGE 4
Grouping 2 Application (Max. node=5) 3. Advanced Programming However, the BASIC_SET command will be also sent to the nodes of Grouping 2. For instance, a lamp module will be turned off after receiving the BASIC_SET command. The following information is for someone that has some experience setting up a Z-Wave system or someone that has computer software running a Z-Wave controller.
PAGE 5
Specifications 5. Command Classes The Door/Window Detector supports Command Classes including… Battery CR2450 3.
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.