User's Manual

ManualsBrandsEverspring Industry ManualsElectronicsDoor/Window Detector

SM810

DOOR/WINDOW DETECTOR

The Door/Window Detector is a Z-Wave Plus

enabled device and is fully compatible with any Z-Wave

enabled network. The device can be set up in a Z-wave network to communicate directly with other end

devices such as lighting controllers, or to report directly to a Z-wave controller (usually a gateway).

Z-Wave

enabled devices displaying the Z-Wave

logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave

enabled networks.

Inclusion of this Door/Window Detector on other manufacturer’s Wireless Controller menu allows remote

turn-on of connected modules and their connected lighting when the Detector is triggered.

Product Overview

LED

TAMPER

SWITCH

BATTERY

MYLAR

SCRE

Adding to Z-Wave Network

Auto Inclusion

The detector supports Auto Inclusion feature where it will automatically enter Inclusion mode when first

powered up after a factory reset.

1. In the front casing, there is a tamper switch which is used to carry out inclusion, exclusion or reset.

2. Put a Z-Wave Controller into inclusion mode.

3. Insert 2 CR2032 batteries to the battery compartment with the correct polarity. The LED on the

device will turns on.

4. The Inclusion process should be completed when the LED turns off.

Note: If Auto Inclusion fails, refer to the Troubleshooting section regarding Manual Inclusion.

Testing

1. Remove the battery cover with the tamper switch not being pressed on the detector (test mode),

detach or close the magnet from the Detector, the LED on the detector will illuminate.

2. After proper installation and test, put the battery cover back to the detector and the detector enters

the normal mode.

Note: After removing batteries, wait for 5 seconds to refit batteries.

Mounting the Detector

Choosing the location

The Door/Window Detector is suitable for mounting in dry interior locations only.

Decide which doors/windows are to be protected by Door/Window Detectors, (usually the front and back

doors as a minimum will have Door/Window Detectors fitted). Additional detectors may also be fitted

where required to other vulnerable doors or windows, (e.g. garage, patio/conservatory doors etc).

Note: Take care when fixing the Detector to a metal frame, or mounting within 1m of metalwork (i.e.

radiators, water pipes, etc) as this could affect the radio range of the device. If required, it may be

necessary to space the magnet and detector away from the metal surface using a plastic or wooden

spacer to achieve the necessary radio range.

Installation

1. Use the adhesive tape to fit detector on the door or window.

2. Fit the magnet to the moving part of the door/window opposite the detector using the adhesive tape.

3. Ensure that the parallel gap between the magnet and detector is less than 20mm and that the

matching line on the magnet is pointing towards and aligned with the line on the detector. An alarm

condition will be occurred if the gap is greater than 35mm.

Operation

1. If first use of SM810 with no node ID, LED will turns ON for 30 sec. when first power on the device

to lead the user for auto inclusion. After Inclusion is completed, the device will stay awake for 25

sec. for set up by user from the controller. After 25 sec., the unit will enter sleeping mode, if set up

is still needed, the user can press tamper switch for SM810 to be awake for another setting.

2. Due to limited power from CR2450, the unit may not continuously operate for a long time due to

power consumption. Therefore, set up time for SM810 should be minimized, and repeatedly

press of Tamper should be avoided as well, in order to prevent unusual incident by a quick battery

voltage drop down.

3. User can enter test mode by releasing the Tamper switch; in the meantime if magnetic sensor is

triggered then the LED will be illuminated. User can confirm whether the Tamper switch has been

pressed properly by implementing this function. When Tamper switch is to be pressed and enter

normal mode, LED will not be illuminated even if the magnetic sensor is triggered, unless low

battery is detected.

4. When the tamper switch is pressed, the unit enters normal mode and the red indicator LED on the

Detector will not illuminate to conserve battery life when the detector is triggered, (unless the battery

power is low).

Battery Cover

45°

Battery Cover

CR2450

Battery

Detector Magnet

Summary of content (3 pages)

PAGE 1
SM810 DOOR/WINDOW DETECTOR 4. The Inclusion process should be completed when the LED turns off. Note: If Auto Inclusion fails, refer to the Troubleshooting section regarding Manual Inclusion. Testing The Door/Window Detector is a Z-Wave PlusTM enabled device and is fully compatible with any Z-WaveTM enabled network. The device can be set up in a Z-wave network to communicate directly with other end devices such as lighting controllers, or to report directly to a Z-wave controller (usually a gateway).
PAGE 2
Programming Door/Window detector trigger OPEN 0x06 0x16 null Z-Wave Group Door/Window detector trigger Close 0x06 0x17 null The detector supports either one of two Z-wave Association Groups: Group 1: Association with 1 Controller node. Group 2: Association with 4 nodes (i.e. end devices such as smart plugs and other lighting controllers). This allows the detector to transfer commands directly to end devices without the participation of the controller.
PAGE 3
Auto Inclusion Manual Inclusion Exclusion Factory Reset (This procedure should only be used when the controller is inoperable.) frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.