Use and Care Manual
Table Of Contents
- Preface
- 1 Scope
- 2 Reference publications
- 3 Definitions and abbreviations
- 4 Design requirements
- 4.1 Supply fittings
- 4.2 Servicing
- 4.3 Installation
- 4.4 Threaded connections
- 4.5 Connections other than threaded connections
- 4.6 Accessible designs
- 4.7 Backflow prevention
- 4.8 Cover plates and escutcheons
- 4.9 Toxicity and lead content
- 4.10 Frost-proof faucets and hydrants
- 4.11 Showerheads, body sprays, and hand-held showers
- 4.12 Cross-flow
- 4.13 Fittings incorporating electrical features
- 4.14 Materials
- 4.15 Automatic compensating valve temperature control
- 4.16 Lawn faucets
- 4.17 Flexible water connectors
- 4.18 High-efficiency commercial pre-rinse spray valves
- 4.19 Household hot water dispensers with storage electrical heating systems
- 5 Performance requirements and test procedures
- 5.1 General
- 5.2 Coatings
- 5.3 Pressure and temperature
- 5.4 Flow rate
- 5.5 Operating requirements
- 5.6 Life cycle
- 5.7 Resistance to installation loading
- 5.8 Resistance to use loading
- 5.9 Backflow prevention
- 5.10 Lawn faucets
- 5.11 Alternative materials test
- 5.12 High-efficiency showerheads and hand-held showers
- 5.13 High-efficiency commercial pre-rinse spray valves
- 6 Markings, packaging, and installation instructions
- Annex A (informative) Unit conversion and rounding criteria
- Annex B (normative) Tests by fitting type
ASME A112.18.1-2018/CSA B125.1-18 Plumbing supply fittings
July 2018 © 2018 Canadian Standards Association
2
5.1 General 35
5.1.1 Preconditioning
35
5.1.2 Installation for testing
35
5.1.3 Test conditions
35
5.1.4 Order of tests
35
5.2 Coatings
35
5.2.1 General
35
5.2.2 Corrosion (all substrates and coatings) 35
5.2.3 Adhesion
36
5.2.4 Decorative organic coatings
37
5.3 Pressure and temperature
38
5.3.1 Static and dynamic seals
38
5.3.2 Burst pressure
38
5.3.3 Cross-flow check valves
39
5.3.4 Hose assemblies
39
5.3.5 Ball joints
39
5.3.6 Diverters
40
5.3.7 Aerators and other end point devices
40
5.3.8 Low-pressure water dispensers
40
5.4 Flow rate
41
5.4.1 Supply fittings
41
5.4.2 Test procedure
41
5.4.3 Test procedure for high-efficiency commercial pre-rinse spray valves
42
5.5 Operating requirements
42
5.6 Life cycle
43
5.6.1 Performance requirements
43
5.6.2 Test procedures
44
5.6.3 Fittings and other control devices
45
5.7 Resistance to installation loading
48
5.7.1 Bending strength
48
5.7.2 Thread torque strength
48
5.8 Resistance to use loading
49
5.8.1 Operating controls
49
5.8.2 Maintenance of installed position
49
5.8.3 Swing spout strength
49
5.9 Backflow prevention
50
5.9.1 General 50
5.9.2 Fittings with plain outlets
50
5.9.3 Fittings with submersible outlets
51
5.10 Lawn faucets
54
5.10.1 Performance requirements
54
5.10.2 Test procedure
54
5.11 Alternative materials test
54
5.11.1 Performance requirements
54
5.11.2 Test procedure
55
5.12 High-efficiency showerheads and hand-held showers
55
5.12.1 General
55
5.12.2 Flow rate
55
5.12.3 Spray force
56