User Manual

E009-00-000246
The instructions below will walk you through the removal of the original heatsink, fan(s),
EVGA HYBRID module installation and replacement shroud. Please see below for SKU’s
compatible with this cooler:
The following instructions and pictures are provided to assist your installation of the EVGA
RTX 2080 Ti/2080/2070 XC HYBRID Cooling Kit to the EVGA RTX 2080 Ti/2080/2070 XC
graphics cards. Please be careful installing the Kit; there are several very small fasteners
used that can be stripped if you are not careful.
Please be sure to keep your original shroud, heatsink, and screws so
your card can be returned to its original condition in case you ever
need to submit for warranty.
Included Accessories:
3. Remove heatsink and fan, while carefully disconnecting fan and LED connectors.
(a) You may need to gently twist the thermal module to loosen up the heatsink from the thermal
pads and GPU thermal grease. Once loose, gently lift the side of the heatsink to expose the fan
and LED connector.
(b) Please be careful when removing the fan/LED connector, because the wires can snap if pulled
too hard. Set aside the heatsink/fan, as it will no longer be needed for this Kit.
4. Clean the card for installation:
Remove all thermal grease on the GPU and remove
any pads that stick to the PCB. Clean the GPU with
high-percentage isopropyl alcohol and a lint-free
cloth. You may try to reattach the thermal pads to the
same location on the original cooler in case you need
to return the card to its original state for warranty
purposes. After you are finished cleaning, the card
should look like these photos:
*Please note that the accessory list above covers all items expected to be
included in the XC HYBRID Kit. There are two types of heatsinks for the Memory
and VRM, but this Kit only includes the heatsink that is designed for your card.
It is possible that you may receive extra accessories that will go unused after
completion of the installation manual. Please follow all directions carefully, and
contact EVGA Customer Service if you have any missing accessories or questions.
See the instructions below.
1. Remove the 20 screws circled in the picture to the right using a Phillips #1
screwdriver. Carefully set aside, as these screws will not be used again. If your
card has a backplate, it is not necessary to remove the backplate to install the
XC HYBRID Kit, but it is necessary to remove the screws so that the heatsink
and fan can be removed.
2. Loosen, but don’t remove, the screws circled on the bracket in the images to the right with
a Phillips #1 screwdriver. You will tighten both the bracket and these screws at a later step.
There is no need to remove the bracket to complete all steps.
2080/2070 Baseplate 2080 Ti Baseplate
2080/2070
2080 Ti
(a)
(b)
3
4
2
1
11 12
9
1086
5
7
EVGA 2080/2070 VRM Heatsink (a)
EVGA 2080 Ti HYBRID VRM Heatsink (a+b)
4
M2x5mm 17pcs screw.
PN:BAA120050052 (for users who don't install backplate)
5
EVGA HYBRID Shroud
EVGA 2080/2070 HYBRID Baseplate
EVGA 2080 Ti HYBRID Baseplate
EVGA HYBRID Pump and Radiator
1
2
3
M2x7mm 17pcs screw.
PN:BAA120070024 (for users who do install backplate)
6
Screw nut 2pcs. PN:BAA350030000
M2x4mm 2pcs screws. PN:BAA120040056
M2x3mm 4pcs. PN:BAA125088001-B
8
9
7
10
11
Cable ties 2pcs hook and loop and 4pcs zip ties.
12
4pcs screw and 4pcs washer to mount radiator.
Mylar 5pcs. PN:BGD100000003
08G-P4-2080-KR
08G-P4-2070-KR
11G-P4-2381 -KR 11G-P4-2281 -KR
08G-P4-21 81 -KR 08G-P4-2081 -KR
08G-P4-21 71 -KR
11G-P4-2382-KR 11G-P4-2282-KR
08G-P4-21 82-KR 08G-P4-2082-KR
08G-P4-21 72-KR 08G-P4-2071-KR
08G-P4-1171 -KR
11G-P4-2387-KR 11G-P4-2385-KR
08G-P4-21 87-KR 08G-P4-2185-KR
11G-P4-2383-KR
08G-P4-21 83-KR
08G-P4-21 73-KR