EVL PRO SCANNER 150-250 / PRO STAR 150-250 USER MANUAL (VER3.
PRO SCAN 150-250 PRO STAR 150-250 1
For your own safety, please read this user manual carefully before installing the device. Ke ep this devi ce away f rom rai n and moisture ! U nplug mains l ead before opening the housing. Every person involved with the installation, operation and maintenance of this device has to: -be qualified -follow carefully the instructions of this manual INTRODUCTION: Thank you for having chosen this professional lighting . effect You have acquired a powerful and versatile device. Unpack the device.
For safe operation, it is absolutely necessary to follow the safety instructions and warning notes written in this user manual. If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore it is essential that the device be earthed.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation. Please use the original packaging if the device is to be transported. For safety reasons, please be aware that all modifications on the device are forbidden. If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void.
1) Unscrew the 2 screws on the back of the housing, holding the plate where the lamp is underneath. 2) Gently pull the socket holder using the knob in the middle. 3) Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp. Gently slide the lamp and its lamp holder back into place and fasten the 2 screws. 4) On the access plate there are 3 small screws marked 1,2 and 3.which are used to adjust the lamp holder in the lamp housing.
Cautions: The effect should be installed outside areas where persons may reach it, walk by or be seated. When installi ng the device, make sure there is no highly inflammable material within a distance of min. 0,5m Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself.
DMX-512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.
If you set a different address, each unit will start to ' listen' to the channel number you have set, based on the quantity of control channels of the unit. That means changing the settings of one channel will affect only the selected fixture. In the case of the scanner, which is a 8 channel fixture, you should set the starting address of the first unit to 1, the second unit to 9 (8 + 1), the third to 17 (9 + 8), and so on.
4 CLLT ON/OFF STEP S-01 ~ S- 48 SC 01 ~ SC 48 E DI T Clear lamp time 01XX (00~FFH) 30XX (00~FFH) T - - X (1~ 9) ON/OFF C-01 ~ C-30 TIME (sec.) CNIN Steps of Program Run Edit the channels of each scene Time for each scene Edit program via controller Main functions - Main menu 0 1. Press [ENTER] 2. Press [ENTER] 3. Press [ENTER] for 3 seconds to enter the main menu "M ODE " (display flashing) and select "ADDR" , ' RUN' or "DISP" by pressing [UP] button. for selecting the desired sub menu.
1. 2. 3. 4. 5. Select "AUTO" or "SOUN" by pressing [UP] . Press [ENTER] for selecting the desired extension menu. Select "ALON" or "MAST" by pressing [UP] . Press [ENTER] to confirm. Press [EXI T/DN] in order to return to the main menu. Display the DMX value, Reverse display, Shut off LED display Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel. 1. Select "V ALU" by pressing [UP] . 2. Press [ENTER] to confirm; the display shows'D -00' .
Main Menu 2 1. Press [ENTER] for 3 seconds to enter the main menu (display flashing). 2. Press [UP] to select 'SET .' Pan Reverse With this function you can reverse the Pan-movement. 1. Select 'rPAN' by pressing [UP] button. 2. Press [ENTER] , the display shows 'ON ' or 'OFF'. 3. Press [UP] to select 'ON ' if you wish to enable this function or 'OFF ' if you don' t. 4. Press [ENTER] or. Tilt Reverse With this function you can reverse the Tilt-movement. 1. Select 'rTIL' by pressing [UP] button. 2.
Software version With this function you can display the software version of the device. 1. Select 'VER ' by pressing [UP] button. 2. Press [ENTER] , the display shows 'V -X .X ' , ' X.X' stands for the version number, e.g. ' V-1.0' , 'V -2.6' . 3. Press [ENTER] or [EXI T/DN] in order to return to the main menu. Main menu 3 1. Press [ENTER] for 3 seconds to enter the main menu (display flashing). 2. Press [UP] to select ' ADJ U' .
Lamp running time With this function you can display the running time of the lamp. 1. Select 'LA T I ' by pressing [UP] button. 2. Press [ENTER] , the display shows ' X X XX' , ' X' stands for the number of hours. 3. Press [ENTER] or [EXI T/DN] to exit. Clear fixture time With this function you can clear the running time of the device. 1. Select 'CLMT' by pressing [UP] button. 2. Press [ENTER], the display shows 'ON ' or 'OFF' . 3.
4. Press [ENTER] , the display shows 'C -X ' , 'X' stands for the channel no. Such as 'C -01' , it means you are editing channel 1 of the selected scene. 5. Select the channel no. you would like to edit by pressing [UP] . 6. Press [ENTER] to enter editing for the selected channel , the fixture reacts to your settings. The display shows the DMX value of the edited channel. Such as ' 11XX', it stands for in the channel 11 of the editing scene, the DMX value is XX , XX is a hexadecimal number value ' 01-FF'.
V3.2 La m p Dim m e r V3.3 La m p Dim m e r DMX channel's function and values:(V ER3.
120-139 140-159 160-179 180-199 200-255 Channel 2 - Light Yellow Yellow Green Blue Red Backwards rainbow effect from slow to fast Rotating gobos, cont. rotation : 0-13 14-27 28-41 42-55 56-69 70-83 84-97 98-115 116-135 136-155 156-175 176-195 196-215 216-235 236-255 Open Rot. gobo 1 (metal) Rot. gobo 2 (metal) Rot. gobo 3 (metal) Rot. gobo 4 (metal) Rot. gobo 5 (metal) Rot. gobo 6 (metal) Rot. gobo 7 (metal) Rot. gobo 1 (metal) shake Rot. gobo 2 (metal) shake Rot. gobo 3 (metal) shake Rot.
(When Channel 6 is Barrel ) 0-7 8-127 128-135 136-255 No rotation forwards Barrel rotation from fast to slow No rotation backwards barrel rotation from slow to fast Channel 7 - Speed pan/tilt movement: 0-225 max to min speed 226-235 blackout by movement 236-245 blackout by all wheel changing 246-255 no function Channel 8 - reset, internal programs: 0-19 20-39 40-59 60-79 80-99 100-119 120-139 140-159 160-179 180-199 200-219 220-239 240-255 255 colour change normal colour change to any position colour cha
4-255 Channel 2 0-9 10-19 20-29 30-39 40-49 50-59 60-69 70-79 80-95 96-111 112-127 128-143 144-159 160-175 176-191 192-255 Channel 3 0-7 8-127 128-135 136-255 Channel 4 0-31 32-63 64-95 96-127 128-159 160-191 192-223 224-255 Backwards rainbow effect from slow to fast Rotating gobos, cont. rotation : Open Rot. gobo 1 (metal) Rot. gobo 2 (metal) Rot. gobo 3 (metal) Rot. gobo 4 (metal) Rot. gobo 5 (metal) Rot. gobo 6 (metal) Rot. gobo 7 (metal) Rot. gobo 1 (metal) shake Rot. gobo 2 (metal) shake Rot.
128-135 136-255 No rotation backwards barrel rotation from slow to fast Channel 7 - Speed pan/tilt movement: 0-225 max to min speed 226-235 blackout by movement 236-245 blackout by all wheel changing 246-255 no function Channel 8 - Lamp on/off, reset, internal programs: 0-127 128-138 139-160 161-171 172-182 183-193 194-204 205-215 216-226 227-237 238-248 249-254 255 colour change normal &Dimmer 0%~100% colour change to any position No function Motor reset Internal program 1 Internal program 2 Internal pr
TECHNICAL SPEC IFICAT IONS Power supply : 110VAC,50Hz; 110VAC,60Hz; 120VAC, 50Hz; 20VAC,50Hz; 230VAC,50Hz; 240VAC, 50Hz; 120VAC,60Hz; 220VAC,60Hz; 230VAC,60Hz; 240VAC,60Hz; Power consumption: max. 250W 300W 400W Lamp : CDMT150 GY9.5 socket, Metal Halide; MSD250 GY9.5 socket, Metal Halide; Motors : 6 micro motors Net weight : 10.5KGS; Gross weight: 12.5KGS; Packing dimensions : 64x37x37cm 12KGS; 14KGS; Erors and omissions for every information given in this manual excepted.
MI NI - CONTROL- 04 DMX512 30P 10K DMX512 LED7X4 104 30P 10PI N 87LPC768 2K 2K 2K 2K 470 10K COLOR CM 8 7LPC768 16MHz 2200UF/ 25V 104 4A 104 4A 4A TWO AC12V 470U/ 16V SCAN6CH- 01 4A 104 30P SCAN6CH- 01 100 4. 7K 220 0UF/ 50V FAN CM1 L293D AT89C52/ 1 CAT24C021 16MHz 1015 30P 10K L293D 1015 1015 87LPC768 10K 4.
MI NI - CONTROL- 04 DMX512 30P 10K DMX512 LED7X4 104 30P 10PI N 87LPC768 2K 2K 2K 2K 470 10K COLOR CM 8 7LPC768 16MHz 2200UF/ 25V 104 4A 104 4A 4A TWO AC12V 470U/ 16V SCAN6CH- 01 4A 104 30P SCAN6CH- 01 100 4. 7K 220 0UF/ 50V FAN CM1 L293D AT89C52/ 1 CAT24C021 16MHz 1015 30P 10K L293D 1015 1015 87LPC768 10K 4.
NOTES 23