OWNER & INSTALLATION MANUAL Affinity 30Ge Cooktop Evo Affinity 30Ge Electronically-Controlled Gas Cooktop For Indoor Use Only Certification: ANSI Z83.11b - 2009. OMNI Report #: 141-S-04b-5 Part #: Commercial models: 10-0050-NG | 10-0050-LP, Residential models: 10-0051-NG | 10-0051-LP, Doc: OM-C&R-30Ge v2 05/2013 Copyright © 2013 Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.
INSTALLATION INSTRUCTIONS Affinity 30Ge THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND, AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL. DANGER POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH WARNING POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY CAUTION POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY.
INSTALLATION INSTRUCTIONS Affinity 30Ge Warnings FOR YOUR SAFETY FOR YOUR SAFETY 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. An LP Tank not connected for use shall not be stored in the vicinity of this or any other appliance. If You Smell Gas: 1. Shut off gas to appliance. 2. Extinguish any open flame. 3. Remove grill cooking surface. 4. If odor continues, immediately call your gas supplier or your fire department. 5.
INSTALLATION INSTRUCTIONS Affinity 30Ge READ FIRST IMPORTANT PRODUCT AND SAFETY INFORMATION WARNING INSTALLATION OF THIS UNIT MUST BE DONE BY A QUALIFIED PLUMBER AND ELECTRICIAN. INCORRECT INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. THIS UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL LOCAL AND UNIFORM BUILDING/ CONSTRUCTION CODES.
INSTALLATION INSTRUCTIONS Affinity 30Ge EVO RESIDENTIAL LIMITED WARRANTY TERMS Evo, Incorporated warrants to the original residential consumer-purchaser that the Evo grill shall be free from rust-through on all metal surfaces and shall be free from defects in materials and workmanship under normal and reasonable use from the original date of purchase.
INSTALLATION INSTRUCTIONS Affinity 30Ge EVO COMMERCIAL LIMITED WARRANTY TERMS Evo, Incorporated warrants to the original commercial foodservice purchaser that the Evo cooking, refrigeration and ventilation equipment shall be free from rust through on all metal surfaces and shall be free from defects in materials and workmanship under normal and reasonable use for One Year from the original date of purchase from Evo, Inc. This warranty is for the benefit of the original use purchaser and is non-transferable.
INSTALLATION INSTRUCTIONS Affinity 30Ge INSTALLATION CHECKLIST PAGE # UNPACK COOKTOP COMPONENTS Follow unpacking instructions carefully 8 PREPARE COUNTERTOP FOR INSTALLATION 9-13 INSERT CHASSIS IN COUNTERTOP 14 INSTALL DRIP PAN 15-16 INSTALL DRIP PAN GASKET 16 INSTALL ELECTRICAL TC CONNECTIONS TO COOK SURFACE 17-18 INSTALL COOK SURFACE AND TIGHTEN FASTENERS 19-20 CONNECT ELECTRICAL AND GAS LINES 21 CHECK INSTALLATION 22 Evo, Inc. | 8140 SW Nimbus Ave.
INSTALLATION INSTRUCTIONS Affinity 30Ge UNPACKING COOKTOP COMPONENTS Cook Surface: Lift and separate cook surface from unit and place next to installation area. Use caution when lifting. The cook surface is heavy. Drip Pan Gasket: Gasket is secured to top of drip tray. Remove gasket from drip tray and set aside for reinstallation. Drip Pan Unlatch pan from circular skirt, then carefully lift and separate drip pan from unit and place next to installation area.
INSTALLATION INSTRUCTIONS Affinity 30Ge CLEARANCE DIMENSIONS 36” clearance to ceiling from cook surface 12” clearance to sidewall from cook surface 12” clearance to backwall from cook surface Minimum 3” clearance required under unit venting to 22 sq/in of combustible air. Do not install above any equipment, table or shelving where air temperature is greater than ambient air temperature.
INSTALLATION INSTRUCTIONS Affinity 30Ge COUNTERTOP INSTALLATION (1 of 4) R181 " 8 460.38mm Cabinetry Box: minimum 3 cm below countertop surface Countertop with substrate underlayment TOP VIEW 2623 " 32 678.51mm 1313 " 16 350.52mm 131 " 8 333.38mm Countertop overhang to cabinet front 115 " 32 37.16mm 273 " 4 704.85mm 2719 " 32 701.04mm OPENING IN COUNTERTOP FRONT STEP 2: Mark the finished position of the Evo Affinity 30Ge drip pan on the countertop using the dimensions shown.
INSTALLATION INSTRUCTIONS Affinity 30Ge COUNTERTOP INSTALLATION (2 of 4) Black o-ring under drip pan bead CORRECT ALIGNMENT OF DRIP PAN AND CHASSIS TO COUNTERTOP INCORRECT ALIGNMENT OF DRIP PAN AND CHASSIS TO COUNTERTOP Possible reasons for incorrect alignment: 1. Top of cabinetry box is less than 3 cm from countertop 2. Chassis mounting brackets are too high.
INSTALLATION INSTRUCTIONS Affinity 30Ge COUNTERTOP INSTALLATION (3 of 4) SIDE VIEW 251 " 4 641.35mm 7.65in 194.36mm Metal Right Angle Mounting Brackets (supplied) 13 " 16 30mm 69 " 3X 16 166.55mm Finished cabinet face set back from finished countertop front edge 815 " 32 215.32mm 223 " 32 69.21mm Shelving or drawers can be installed under Affinity 30Ge if desired. Example of 3/8” tile with substrate for a minimum 3 cm overall. Make sure you allow for the countertop overhang as shown.
INSTALLATION INSTRUCTIONS Affinity 30Ge COUNTERTOP INSTALLATION (4 of 4) Example: Tiled countertop with substrate. Finished countertop thickness should be 3 cm. FRONT VIEW 273 " 4 704.85mm 19 " 16 40mm Cabinet Framework 13 " 16 30mm 7.65in 194.36mm Metal right angle mounting brackets supplied with unit are each 1/16” thick. Mount angle brackets as shown. Unit slides into framework and rests on top side of brackets. Brackets are slotted for fasteners at each four corners.
INSTALLATION INSTRUCTIONS Affinity 30Ge INSERT CHASSIS IN COUNTERTOP 3 WIRE SERVICE LINE: black, white and green 120V, 1-Phase, 50-60Hz 15AMP circuit Use supplied 1/4” fasteners to bolt chassis to angle brackets. STEP 4: Slide the Affinity 30Ge chassis into the countertop so it rests on top of the installed brackets. Bolt unit to angle brackets using supplied 1/4” x 20 fasteners from underside.
INSTALLATION INSTRUCTIONS Affinity 30Ge DRIP PAN INSTALLATION Using a #3 Phillips flat screwdriver, ensure captive fasteners on chassis skirt are threaded inward before drip pan is secured. Drip Tray Catches GRILL FRONT STEP 5: Locate the two captive fasteners on the front of the chassis circular skirt and ensure they are threaded inward. Slide drip tray over chassis circular skirt positioning spillover slots to the corresponding slots of the top chassis deck.
INSTALLATION INSTRUCTIONS Affinity 30Ge DRIP PAN AND GASKET INSTALLATION Use No. 3 Phillips screwdriver to secure drip pan at the access points. drip pan gasket - seam at rear (opposite to chef side) CROSS SECTION OF CHASSIS ACCESS SLOT A CROSS SECTION OF DRIP PAN TOP B CROSS SECTION OF DRIP PAN EDGE C countertop chassis skirt Hook drip pan latch under chassis catch and tighten screw at chassis access slot. drip pan Slip gasket ring onto top of drip pan so it creates a seal to the chassis skirt.
INSTALLATION INSTRUCTIONS Affinity 30Ge CONNECTING COOK SURFACE - ELECTRICAL CONNECTIONS 1 of 2 IT IS HIGHLY RECOMMENDED THAT TWO INSTALLERS BE PRESENT TO CONNECT THE TC’S AND INSTALL THE COOK SURFACE. Place suitable protection on drip pan (towel or cardboard). Place cook surface vertically with Bullet Fastener facing downward.
INSTALLATION INSTRUCTIONS Affinity 30Ge CONNECTING COOK SURFACE - ELECTRICAL CONNECTIONS 2 of 2 Outer Zone Outer Zone While one installer supports cook surface, the other installer extends the TC wires up through the heat shield and connects to each respective stud using 1/4 x 20 Hex Nuts. Hex nuts only need moderate tightening. 2 3 Inner Zone 1 Outer Zone 4 DO NOT OVER TIGHTEN TC-WIRE HEX NUTS. DOING SO WILL BREAK THREADED WELD STUD ON COOK SURFACE.
INSTALLATION INSTRUCTIONS Affinity 30Ge INSTALLING COOK SURFACE (1 OF 2) Cook surface support tabs BOTTOM-UP VIEW OF REAR COOK SURFACE CUT AWAY VIEW OF REAR COOK SURFACE SHOWING BULLET ENGAGED IN CHASSIS SLOT A Rear bullet C B STEP 8: Before lowering cook surface, ensure the two slotted captive fastener screws are backed out fully (see page 16). Then place cook surface over circular skirt with the three support tabs (located under cook surface) resting on the chassis skirt top.
INSTALLATION INSTRUCTIONS Affinity 30Ge INSTALLING COOK SURFACE (2 OF 2) CUT AWAY VIEW OF FRONT CAPTIVE FASTENERS Tighten two front captive fastener screws into fastener slots located underneath cook surface (non visible). Lift surface slightly to check screws are secure in slots. STEP 9: Tighten the two captive screws clockwise so they engage into the slots on the underside of the cook surface. Test to ensure screws are secure by lifting cook surface slightly.
INSTALLATION INSTRUCTIONS Affinity 30Ge CONNECTING ELECTRICAL AND GAS FOR YOUR PROTECTION, WE RECOMMEND A QUALIFIED ELECTRICIAN AND PLUMBER INSTALL THIS COOKTOP. THIS PERSON SHOULD BE FAMILIAR WITH ELECTRICAL AND GAS SERVICE INSTALLATIONS AND ALL LOCAL CODES. PROPER CONNECTIONS ARE ESSENTIAL FOR EFFICIENT OPERATION AND SAFETY.
INSTALLATION INSTRUCTIONS Affinity 30Ge CHECK INSTALLATION Check to ensure the following items are complete: PAGE # DRIP PAN PROPERLY INSTALLED Ensure that the drip pan half-rolled top bead overhangs the cutout dimension by .25” and the black o-ring is creating a seal against the countertop. 15-16 DRIP PAN GASKET SECURED Black drip pan gasket should fit properly and create a seal where the drip pan meets the chassis skirt. 16 INSTALL ELECTRICAL AND GAS CONNECTIONS Test unit for proper operation.
INSTALLATION INSTRUCTIONS Affinity 30Ge EVO AFFINITY 30Ge ELECTRIC CONTROL PANEL DISPLAY SET ON/OFF INNER 000F. HOT SURFACE OUTER MODE ON/OFF OUTER 000F. Displays temperature for Inner burner (zone) in Fahrenheit degrees whenever Inner control knob is selected. The Dot mark after F is illuminated when burner is ignited. Inner display remains illuminated whenever Inner burner is selected. 000F.
OPERATOR INSTRUCTIONS Affinity 30Ge EVO AFFINITY 30Ge TEMPERATURE CONTROL Inner Burner Outer Burner Control Display with On/Off switch Inner Burner Control Knob Outer Burner Control Knob Inner Burner and Inner Control Knob - The Inner Burner is a 10” diameter gas fired burner operating at 20,000BTU’s. This burner is controlled by the Inner or center-most control knob. Temperatures are adjustable from 250F° to 650F°.
OPERATOR INSTRUCTIONS Affinity 30Ge REMOVABLE SPILLOVER TRAYS Spillover Slot Removable Ninth-Pan Spillover Tray Drawer Pull Recess Removable Drawer Slides Do not operate cook top or clean drip pan into spillover slots without spillover trays installed in spillover drawers. Failure to install ninth-pan spillover trays will result in cooking grease contamination to the underside of drawer. This requires immediate drawer removal and cleaning.
OPERATOR INSTRUCTIONS Affinity 30Ge COOK SURFACE MAINTENANCE Regular cleaning and care for your Evo Affinity 30Ge cooktop will keep it looking and functioning it’s best. The cook surface is designed to hold a fine layer of cooking oil creating a ‘seasoning’ on its surface. This seasoning promotes a non-stick cooking surface and is easily maintained. Caring for Evo’s cook surface is much like maintaining cast iron cookware. When the surface requires cleaning, there are a few basic cleaning techniques to use.
TC 4 R1 R2 9 I G N I T I O N A S G 7 8 7 6 6 5 5 Fenwal 35-67 O N T R O L L E R C 4 4 2 1 3 2 1 Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com Remote Flame Sense Remote Flame Sense FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY SUITABLE FOR AT LEAST 90°C (194°F). #12 AWG OR LARGER.
INSTALLATION INSTRUCTIONS Affinity 30Ge GAS REGULATOR The Affinity 30Ge cooktop uses a Robert Shaw 4080 Series gas regulator installed under the access panel on the right rear quarter of the chassis box. Listed below are the manufacturer specifications. As a default, all Affinity 30Ge appliances, unless otherwise specified, are shipped configured as Natural Gas. 28 Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.
INSTALLATION INSTRUCTIONS Affinity 30Ge CHECKING TCU AND ELECTRICAL CONNECTIONS HIGH VOLTAGE DO NOT ATTEMPT TO CHECK ELECTRICAL CONNECTIONS UNLESS POWER HAS BEEN DISCONNECTED FROM THE UNIT.
