® EVO180 180mm (7”) TCT STEEL CIRCULAR SAW Instruction Manual Read instructions before operating this tool. www.evolutionsteel.
EVO 180mm Steel Cutting Circular Saw GB Original Instructions Read instructions before operating this tool. 2 TABLE OF CONTENTS EC - Declaration of Conformity 03 Important Information 03 12 Month Limited Warranty 03 General Safety Rules 04 Safety Instructions for All Saws…... 05 Symbols & Labels 06 Additional Specific Safety Rules…. 07 Specification 07 Assembly 08 Machine Overview 09 Getting Started 10 Maintenance 13 Environmental Protection 14 Service Parts Diagram……………..
EVO180 EC OF CONFORMITY EC-- DECLARATION DECLARATION OF CONFORMITY GB We, manufacturer and importer IMPORTANT INFORMATION GB Please read these operating and safety instructions carefully and completely. For your own safety, before using this equipment check that the voltage is correct and that all handles and parts are firmly secured. If you are uncertain about any aspect of using this equipment, please contact our Technical Help Resource. Evolution Power Tools Ltd.
No officer, employee or agent of Evolution Power Tools is authorised to make oral representations of fitness or to waive any of the foregoing terms of sale and none shall be binding on Evolution Power Tools. Questions relating to this limited warranty should be directed to the company’s head office, or call the appropriate Helpline number.
EVO180 or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power Tool Use & Care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
forces can be controlled by the operator, if proper precautions are taken. b) If the blades are binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blades come to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blades are in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
EVO180 Only use genuine Evolution replacement parts. Unauthorized parts may be dangerous! To obtain an additional copy of your manual, please contact Evolution Power Tools at: UK WEB 0870 609 2297 www.evolutionpowertools.com in the open position. Ensure that the guard operates freely without jamming. m) Only use blades that comply with the characteristics specified in this manual. Before using accessories, always compare the maximum allowed RPM of the accessory with the RPM of the machine.
ASSEMBLY ASSEMLY GB Your Evolution Power Tools saw is shipped complete. Remove all contents from the box and inspect to ensure no damage was incurred during shipping, and that the items listed below are included. ITEMS SUPPLIED Description Instruction Manual: Allen Key: 180mm Steel Blade (fitted) Discharge Port Exhaust Parallel Edge Guide Carry Case 8 Qty 1 Qty 1 Qty 1 Qty 1 Qty 1 Qty 1 www.evolutionsteel.
EVO180 MACHINE OVERVIEW GB EVO 180MM STEEL CIRCULAR SAW 3 1 2 5 4 1. ON/OFF TRIGGER SWITCH 2. AUXILLARY FRONT HANDLE 3. DISCHARGE EXHAUST PORT 4. LOWER BLADE GUARD 5. FITTED BLADE IN SITU www.evolutionsteel.
GETTING STARTED GETTING STARTED GB WARNING: Always disconnect the saw from the power source before making adjustments. Refer to the “Service Parts Diagram”. Install a blade as detailed in the “Installing or Removing a Blade” section. WARNING: Never start the saw with the cutting edge of the saw blade in contact with the workpiece surface. Do not retract blade guard manually. Guard retracts automatically. This saw is equipped with an approved cord and plug for its intended Country of use.
EVO180 10. Replace the chip collector and securely tighten the two thumb screws. 11. Check that the arbor lock is fully released by manually rotating the blade. 12. Check the operation of the safety guard. Parallel Edge Guide A parallel guide (for help when rip cutting) can be fitted to the sole plate of the machine The guides arms should be inserted into the rectangular slots in the turned up edges of the sole plate, and slid under the locking thumb screws. (Fig.
ON/OFF Trigger Switch This machine is equipped with a safety start trigger switch. To start the machine: • Push in the safety lock button on the side of the handle with your thumb. •Depress the main trigger switch to start the motor. (Fig. 8) Chip Collector FIG 7 This machine is fitted with a chip collector to capture metal chips. The chip collector cover plate is provided with a transparent ‘window’ so that the operator can see the contents and empty when necessary.
EVO180 MAINTENANCE MAINTENANCE Cutting Advice The operator should wear all relevant PPE (Personal Protection Equipment) necessary for the job at hand. This could include safety glasses, dust masks, safety shoes etc. The operator should always be aware of the position and routing of the power cable. • Do not force the machine. • Allow the speed of the saw blade do the work. Cutting performance will not be improved by applying excessive pressure to the machine, and blade life will be reduced.
ENVIRONMENTAL PROTECTION ENVIRONMENTAL PROTECTION GB Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice 14 www.evolutionsteel.
EVO180 EVO180 F11100 www.evolutionsteel.
w w w. e v o l u t i o n p o w e r t o o l s .
