EVO42 42mm MAGNETIC DRILLING SYSTEM Original Instruction Manual Read instructions before operating this tool. Guard omitted for illustrative purposes only. www.evolutionsteel.
EC - DECLARATION OF CONFORMITY GB GB We, manufacturer and importer Evolution Power Tools Ltd. Venture One Original Instruction Manual Sheffield S20 3FR Declare that the product Part numbers: EVO42 Evolution: EVO42 Read instructions before operating this tool.
EVO42 IMPORTANT INFORMATION GB no warranty – written or verbal – for drill bits or cutters. In no event shall Evolution Power Tools Please read these operating and safety instructions be liable for loss or damage resulting directly or carefully and completely. For your own safety, before indirectly from the use of our merchandise or from using this equipment check that the voltage is correct any other cause. and that all handles and parts are firmly secured.
5. Store idle tools. When not in use, tools should 18. Use outdoor extension leads. When the tool is be stored in a dry locked-up place, out of reach of used outdoors, use only extension cords intended children. for outdoor use and so marked. 6. Do not force the tool. It will do the job better and 19. Stay alert. Watch what you are doing, use safer at the rate for which it was intended. common sense and do not operate the tool when 7. Use the right tool. Do not force small tools to you are tired.
EVO42 SPECIFIC SAFETY RULES GB P) Check for damaged parts. Before further use of the tool, a guard or other part that is damaged A) Keep guards in place and in working order. should be carefully checked to determine that B) Remove adjusting keys and wrenches.
LABELS & SYMBOLS GB Noise and Vibration Data WARNING: Do not operate machine if warning Sound pressure level (LpA): 89.4dB(A) and / or instruction labels are missing or damaged. Sound power level (LwA): 102.4dB(A) Contact your supplier for replacement labels. K= 3dB(A) Symbol Vibration Data Description V Volts A Amperes Hz Hertz min-1 Minutes ~ Alternating current No no load speed Ah = 0.629 m/s2 K = 1.
EVO42 ASSEMBLY GB Your Evolution Power Tools saw is shipped complete. Remove all contents from the box and inspect to ensure no damage was incurred during FIG 1 shipping, and that the items listed below are included. ITEMS SUPPLIED Description Quantity Instruction Manual 1 Coolant System 1 Guard 1 Hex Key 2mm 1 Hex Key 3mm 1 Hex Key 4mm 1 Hex Key 5mm 1 FIG 2 Handles 3 Wing Screws 2 Spring Washers 2 Safety Strap 1 Carry Case 1 1.
GETTING STARTED GB INSTALLING THE CHUCK ADAPTOR The optional chuck adaptor (part HTA 47) can be WARNING: Always Disconnect The Machine fitted into the EVO42 machines arbor, and then the From Power Source Before Making machine can be fitted with a standard 3 jawed self Adjustments. Refer to the “Service Parts centering chuck. This enables the EVO42 to take Diagram”. standard parallel twist drills up to ø13mm.
EVO42 etc, should be removed from the work area before 1. Using the supplied 3mm Hex Key slightly loosen the machine is positioned. 10 mm is the optimum the 3 cap screws. (Fig. 6A shows 1 of the cap material thickness for safe operation. Keep the screws). magnet clean of metal chips and other dirt and 2. Using the 2 mm Hex Key supplied turn the 3 debris. These can also seriously reduce magnetic adjusting screws (Fig. 6B shows 1 of the adjusting adhesion.
the machine and allow to run up to full speed. 5. Turn the crank handle to begin cutting. Use light MAINTENANCE GB pressure at first to keep the cutter from wandering, and then gradually increase until normal Note: Any maintenance must be carried out with pressure is being applied. Do not force the tool – the machine switched off and disconnected from let the speed of the cutter do the work. Cutting the mains/battery power supply.
EVO42 www.evolutionsteel.
UK 25.10.
