Version 2014_1 VICTORIAN ASSEMBLY INSTRUCTIONS Victorian Vi 23 / Vi 34
PRODUCT INFORMATION Dear customer Thank you for buying a high-quality aluminium greenhouse. REMARKS In all drawings you find the mounting-instructions for all basic standard-models. However this manual should be a sufficient guidance for all special-case greenhouses. This greenhouse is designed for cultivation of plants/flowers. Therefore leakage, water drops and condensation inside the building are allowed. The building may only be entered by competent persons during cultivation or maintenance.
15.
Vertical Glazing Bar Gable Profile Side Profile Turning Door Side profile Turning Door Side Profile for sliding door Top/Bottom profile of sliding door Hanger for Sliding Door Horizontal Profile Turning Door Curtain Rail Top Shelf
A1
Vi23 Vi23 2360 mm/ 92.91 in 3100 mm/ 122.04 in Vi34 Vi34 3100 mm/ 122.04 in 4580mm/ 180.31 in Note: While the foundation dimensions are provided above we reccomend that you layout the actual greenhouse frame before contruction of the foundation. This will eliminate any possible inconsistencies. Note: Do not fill in corners until the frame is full assebled. You may need to make small adjustements during assembly. Note: Divide millimeters by 25.
" HELIOS - SPECIAL" Version 1 Version 2 A|B A|B A = 2360 | 3100 | 3820 B = 2360 | 3100 | 3820 4580 | 5318 | 6060 C = 794 | 1533 | 2273 D = 774 E = 794 | 1533 | 2273 !!! A= C+D+E !!! 10 263 | 463 H 663 | 1088 200 | 400 H 600 | 1025 A = 2360 | 3100 | 3820 B = 2360 | 3100 | 3820 4580 | 5318 | 6060 C = 794 | 1533 | 2273 D = 1512 E = 794 | 1533 | 2273 !!! A= C+D+E !!! Note: Divide millimeters by 25.
Note: When assembling the foundation in this step only tighten the nuts hand tight. The corners may need to be slightly loose to attach the corner uprights Note: Before assembling the foundation insert 3 M6x15 Bolts as shown for the sliding door guide. See page S1. Suggestion: If the unit is to be installed on a concrete foundation you will need to cut PRO210 flush with the bottom of PRO6120.
Insert bolt in each upright on the side where the top shelf is located. Insert bolt in corner of front and back wall for Seed Tray.
Suggestion: Now is a good time to install the L1 wind braces shown on page H10. Note: If you have purchased shade curtains insert the loops into the gutter profile before this assembly step. This is shown below.
--- -------- Note: Add three bolts to each PRO1456 profile here for the louvre window. See page LR1 -------- ----- --- ------ Insert bolt in each upright on the side where the top shelf is located. Refer to page ZB2 and SC1 --- Note: Add one bolt in the center PRO1456 for the Seedbed support. See page ZB1 --- ---- ---- Note: Use PRO29909 for the door frame.
Note: Add one bolt per end for the roof support tube.
Note: Ends of support tube will need to be bent to fit. Attach the lower end and adjust the top until it fits flush.
Drill a hole and attach wind brace to roof profile with short screw or bolt
Note: Crescent seal is only installed in the roof as shown.
Sliding Door Hanger
Note: Rubber seal only installed on sides of door
Double Sliding Door
Louvre Vent
----- --- --- --- ------- --- --- Squeeze black framing together to secure the glass
3PPG 8JOEPX Note: Rubber seal only installed on sides
Note: Remove automatic opener piston if temperatures are below freezing and the greenhouse is not heated. This may cause premature failure. It is reccomended that the manual opener be used during winter months.
Shade Curtain Note: 4 locking loops are provided, one for each curtain end Suggestion: If you forgot to insert the curtain loops you can drill a hole as shown and slide them in.
Seedbed
------------ -------- --------- ------------ --------- ------------ Suggestion: Use a small strip of tape under each bolt to hold it in place. This will make the shelf installtion a bit easier. (Tape shown as red dotted line.
Exaco Trading 10203 Metropolitan Drive Austin, Texas 78758 Customerservice@exaco.com Toll Free: 1-877-760-8500 www.exaco.com Janssens NV Mechelsesteenweg 388, B-2500 Lier Belgium (T) +32 15 30 67 80 (W) www.janssens-alusystems.be (E) info@janssens-alusystems.
