Information english Exact PipeCut 170/170E System Users manual Guarantee of conformity with EU requirements We Exact Tools Oy, Särkiniementie 5 D 00210 Helsinki, Finland, guarantee that the Exact PipeCut 170/170E to which this statement refers fulfills the basic health and safety requirements mentioned in the (machine directive) EU directive 98/37/EY.
Contents The following symbols are used throughout this manual Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual. Denotes risk of electrick schock. Contents List of contents 1. Guarantee of conformity with EU requirements Foreword 3. Technical data 3. Electrical safety 4. Package contents Safety 5. Safety instructions 6. Use and limitations Operation 7. 8. 8. 8. 9. 9. 10. 10. 10.
Foreword Kuva A Operating, safety, and servicing instructions Please read this operating, safety, and servicing instructions carefully before using the pipe saw. Also store this instruction book somewhere accessible to everyone using the pipe saw. In addition to these instructions, always follow the official work, health and safety regulations. The Exact PipeCut 170/170E is meant for professional use only.
Foreword Exact PipeCut 170/170E pipecutting system, Package contents: Please check the package contains the following items: Pipecutting System case Exact PipeCut 170 or 170E pipe saw Hard-metal blade 140 x 62 fitted on the machine Cutting supports 4x Hex socket key 5 mm and 2 mm fitted to the machine Operating instructions 4
Safety it cannot close in on the sawn gap and clamp onto the blade. The machine works at its best and safest when it is used the way for which it was designed. Safety Instructions In order to prevent, electrical shocks, injuries, and the risk of fire the following basic safety instructions should be followed. Dress suitably Do not use clothing that is too loose or jewellery when using the pipe saw as they could get caught on moving parts of the machine.
Safety Extension cables outside When you work outdoors, always use an extension cable that is made and approved for outdoor use. Intended use and limitations The Exact PipeCut 170/170E pipe saw is intended for use as a pipe fitter’s tool at the installation site. The Exact PipeCut 170/170E pipe saw can only be used to cut round pipes, with a diameter of 15-170 mm and a maximum wall thickness of 6 mm with steel in model 170 or 8 mm in model 170E and 16 mm with plastics.
Operation Fig.
Operation Fig C Exact PipeCut 170/170E pipecutting system operating instructions Before operating the tool Ensure that the motor unit is in the upright position. The yellow mark of the UNLOCK button is visible. Cutting mark Cutting point Check that the blade is correctly fitted, in good condition and suitable for the material to be cut. Ensure the pipe saw guide wheels rotate.
Operation Fig E Attaching the pipe saw to the pipe Open the pipe saw's gripper unit enough to suit the diameter of the pipe by rotating the adjustment handle located at the rear of the saw (Fig. E/1). Position the pipe saw on top of the pipe so that the edge of the lower blade guard is at the cutting mark. Fasten the pipe saw to the pipe by turning the gripper adjustment handle until the gripper grips firmly the pipe to be cut (Figure E/2).
Operation Select the feeding speed as per the material and the thickness of the wall. Too high speed can damage the blade, overload the pipe saw and give a poor sawing result. Fig J When the pipe is cut off, push the UNLOCK button forward until the yellow mark is visible and the locking is released (Fig L/1). Now raise the motor unit to starting position (Fig L/2). Release the power switch (Fig L/3). When the blade is stationary, remove the pipe saw from the pipe by loosening the gripped handle (Fig L/4).
Operation, maintenance The adjustment applies only to the actual pipe size and material, and the wheel may have to be readjusted as the blade is worn.To adjust the wheel, loosen the locking screw (Fig N/1) and turn the wheel centre clockwise or counter clockwise to the desired position (Fig N/2), and lock the wheel again (Fig N/3). If the blade has wandered too much to the left, adjust wheel centre clockwise (- sign). If the misalignment is to the right, adjust counter clockwise (+ sign).
Environment, guarantee Blade Check the condition of the blade. Replace a bent, blunt, or otherwise damaged blade with a new one. Using a blunt blade can overload the pipe saw’s electric motor. When you notice that the blade is blunt, do not continue sawing with it, as the blade may become so badly damaged that it will not be worth sharpening. A blade in sufficiently good condition can be sharpened a few times by a professional sharpening company. Exact-blades. Environment Separate collection.
