User's Manual
Exalt Communications Inc.
EX-2.4i Installation and Maintenance Manual
Page 28
MAN-002400, Revision 001
2005-12-01
9. Help
4.5.2.2 The Configuration menu
The following list is an illustration of the tree structure of the configuration menu.
1. Configuration/Status <menu>
1. Configuration wizard, 1.1, <configwiz>
2. IP setting 1.2, <IPconfig>
1. Display IP address, 1.2.1, <dispIP>
2. Set IP address, 1.2.2, [setip xxx.xxx.xxx.xxx]
3. Display Subnet Mask, 1.2.3, <dispmask>
4. Set Subnet Mask, 1.2.4, [setmask xxx.xxx.xxx.xxx]
5. Display NMS Gateway IP address, 1.2.5, <dispgate>
6. Set NMS Gateway IP address, 1.2.6, [setgate xxx.xxx.xxx.xxx]
7. Display all IP Configuration, 1.2.7, <dispIPall>
3. Configuration File Load/Save, 1.3, <configfile>
1. Load Configuration From File, 1.3.1, [configload c:\filename.cfg]
2. Save Configuration To File, 1.3.2, [configsave c:\filename.cfg]
4. Detailed Configuration Parameters, 1.4, <config>
1. Interface Configuration, 1.4.1, <configintfc>
1. Main Ethernet Configuration, 1.4.1.1, <configmain>
1. Display Main Ethernet Configuration, 1.4.1.1.1, <dispmain>
2. Set Main Ethernet Duplex, 1.4.1.1.2,
[setmainduplex full:half:auto]
3. Set Main Ethernet Speed, 1.4.1.1.3, [setmainspeed 10:100]
2. Aux Ethernet Configuration, 1.4.1.2, <configaux>
1. Display Aux Ethernet Configuration, 1.4.1.2.1, <dispaux>
2. Set Aux Ethernet Duplex, 1.4.1.2.2, [setauxduplex full:half:auto]
3. Set Aux Ethernet Speed, 1.4.1.2.3, [setauxspeed 10:100]
3. T1/E1 Configuration, 1.4.1.3, <configTE>
1. Display T1/E1 Configuration, 1.4.1.3.1, <dispTE>
2. Set T1/E1 Mode, 1.4.1.3.2, [setTE T:E]
3. Configure T1, 1.4.1.3.3, <configT>
1. Set AIS (per channel), 1.4.1.3.3.1, [setAIS Y:N
Y:N Y:N Y:N] (Y=AIS on, N=AIS off)
2. Set LBO (per channel), 1.4.1.3.3.2, [setTLBO 1:2:3:4:5
1:2:3:4:5 1:2:3:4:5 1:2:3:4:5] (1=0-133 ft., 2=133-
266 ft., 3=266-399 ft., 4=399-533 ft., 5=533-655 ft.)
3. Set T1 Line Code (per channel), 1.4.1.3.3.3, [setTcode
A:B A:B A:B A:B] (A=AIS, B=B8ZS)
4. DS3 Configuration, 1.4.1.4, <configDS3>
1. Display DS3 Configuration, 1.4.1.4.1, <dispDS3>
2. Set DS3 Mode, 1.4.1.4.2, [setDS3 On:Off]
3. Set DS3 LBO, 1.4.1.4.3, [setDS3LBO 1:2] (1=0-450 ft.,
2=450-900 ft.)