User's Manual
Table Of Contents
- Legal Notice
- Open-Source License Information
- About this Document
- General Compliance and Safety
- Regulatory Notices
- EU WEEE
- EU RoHS
- Regulatory Notices (4.9GHz Model)
- Safety Notices
- Exalt Limited Hardware Warranty
- Introduction
- Pre-installation Tasks
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- CLI Screens and Menus
- Exalt Graphical User Interface (GUI)
- Quick-Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- System Configuration Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
- File Transfer Page
- File Activation Page
- Simple Network Management Protocol (SNMP) Configuration
- Alarms Page
- Performance Page
- Event Log Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Reboot Page
- Manual Page
- Troubleshooting
- General Practices
- Typical Indications of Issues
- Improper RF Cable Termination
- Multipath Propagation
- RF Interference
- Path Obstruction
- Misaligned Antenna
- Faulty Antenna
- Improper Grounding
- Insufficient Link Margin
- Moisture in the Transmission System
- Physical Specifications
- Common System Specifications
- EX-2.4i System Specifications
- EX-4.9i System Specifications
- EX-5i System Specifications, 5.3 GHz Band
- EX-5i System Specifications, 5.4 GHz Band
- EX-5i System Specifications, 5.8 GHz Band
- Interfaces
- Back-to-back Bench Testing
- DC Coupler for Antenna Alignment
- Interface Connections
- DIP Switch Settings (-16 Models Only)
- Copyright Notices
- Index
Exalt Communications, Inc.
Exalt i-Series Installation and Management Guide
5000001 138
2007-04-15
Minimum RSL field, 95
Minimum RSL Timestamp field, 95
Mode parameter, 79
modes
AUTO SYNC, 41
multi-link backbone, 41
multi-link network, 42
multipath, 106
multipath propagation, 107
muting, 82
N
noise profile, 29
O
offset timing, 43
P
passwords, 32, 70, 89
path obstruction, 108
performance degradation, 105
Performance page, 94
ports
SYNC IN, 44
SYNC OUT, 44
power
AC adapter, 54
DC specifications, 55
DC wiring, 55
system LEDs and, 54
power interface, 117
R
rack mounting
hardware, 47
temperature considerations, 47
radio
default settings, 38
grounding, 29, 109
initiation tasks, 45
installation tasks, 45
maximum transmit power setting, 79
mounting, 29, 47
parameters, 32
rebooting, 97, 102
transmitter output power, 29
Radio A, 38
Radio A configuration, 30
RADIO A LED, 51
radio configuration, 30
radio features, 27
radio firmware files, 87
radio frequency
EX-2.4i, 25
EX-5i, 25
Radio Information page, 75
radio mount
enclosure, 26
connections, 27
indoor, 26
connections, 26
Radio Name parameter, 89
Radio Transmit Power parameter, 78
Reboot page, 102
received signal level (RSL). See RSL
receiver threshold, 29
receiver threshold performance, 32
record keeping, 46
regulatory requirements, 33
EX-2.4i (Canada) EIRP, 36
EX-2.4i FCC EIRP, 34
EX-4.9i (Canada) EIRP, 36
EX-4.9i FCC EIRP, 34
EX-5i (Canada) EIRP, 36
EX-5i FCC EIRP, 35
USA, 33
regulatory rquirements
Canada, 35
repeater, 42
RF cable length, 27
RF connector, 63
RF connector termination, 53
RF Frequency parameter, 80, 89
RF interface, 116
RF interference, 107
RF lightning arrestor, 63
RF output power, 33
RMT button, 53
RMT LED, 52
RSL, 33
current RSL readings, 95
diagnostics, 99
Maximum RSL field, 96
Minimum RSL Timestamp field, 95
monitor for performance, 106
RSL voltage, 64
S
security mode, 32
serial connection settings, 66
serial console interface, 116
Set to E1 button, 83
Set to T1 button, 83
shipping box contents, 31
site preparation, 29
SNMP, 91
spanning tree protocol, 82
specifications, 110
Spectrum Analyzer page, 101
STATUS LED, 51
Swap button, 87, 90
Sync (In/Out) connectors, 125
Sync (In/Out) interface, 117
SYNC IN LED, 52
SYNC OUT LED, 52
SYNC RECIPIENT radio, 41