User's Manual
Table Of Contents
- EX-i Series (TDD)
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with the i-Series Radios
- Initial Configuration and Back-to-Back Bench Test
- RF Output Power Setting
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization
- Radio Synchronization
- Offset Timing
- Virtual Local Area Network (VLAN)
- Link Symmetry
- Simple Network Management Protocol (SNMP)
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- Telnet into the Command Line Interface (CLI)
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- Access Security Page
- System Configuration Page
- MHS Configuration Page
- Ethernet Interface Configuration Page
- VLAN Configuration Page
- T1/E1 Configuration Pages
- DS3 Configuration Page
- GPS Information Page
- Alarms Page
- MHS Status Page
- Performance Page
- Event Log Page
- User Throughput Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Ethernet Utilization Page
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- DIP Switch Settings (-16 Models Only)
- Antennas
- DC Coupler for Antenna Alignment
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Dynamic Frequency Selection
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- Regulatory Domain Keys
- EIRP Limits for the United States and Canada
- EIRP Limits for the European Union and ITU Countries
- EIRP Limits for Australia
- Declaration of Conformity to the R&TTE Directive 1999/5/EC
- END USER AGREEMENT
- Copyright Notices
- Index
Exalt Installation and Management Guide
EX-i Series (TDD) Digital Microwave Radios
206501-018 141
2015-11-06
muting 59
N
noise profile 6
O
offset timing 14
P
passwords 37, 50
path obstruction 105
performance degradation 103
Performance page 70
ports
SYNC IN 15
SYNC OUT 15
power
AC adapter 26
DC specifications 26
DC wiring 27
system LEDs and 26
power interface 89
R
rack mounting
hardware 20
temperature considerations 20
radio
default settings 11
grounding 6, 106
initiation tasks 18
installation tasks 18
maximum transmit power setting 55
mounting 6, 20
rebooting 72, 80
transmitter output power 6
Radio A 11
Radio A configuration 7
radio configuration 7
Radio Information page 42
Radio Name parameter 49
Radio Transmit Power parameter 54
Reboot page 80
received signal level (RSL) See RSL
receiver threshold 6
record keeping 19
Regulatory Domain Key (RDK) 8, 38, 119
regulatory requirements
Canada 114
EX-2.4i FCC EIRP 120, 122
EX-4.9i FCC EIRP 120
EX-5i FCC EIRP 121, 126
US 113
repeater 13
RF connector 32
RF connector termination 25
RF Frequency parameter 50, 55
RF interface 88
RF interference 104
RF lightning arrestor 31
RF output power 9
RMT button 25
RSL 9
current RSL readings 70
diagnostics 75
Maximum RSL field 71
Minimum RSL Timestamp field 71
monitor for performance 103
RSL voltage 32
S
safety 110
serial connection settings 34
serial console interface 88
Set to E1 button 62
Set to T1 button 62
shipping box contents 7
site preparation 6
SNMP 17, 45
SNMP Traps 46
specifications 82
Spectrum Analyzer page 77
Swap button 51
Sync (In//Out) connectors 92
Sync (In//Out) interface 89
SYNC RECIPIENT radio 12
SYNC SOURCE radios 12
synchronization 12
internal 12
system latency 6
system parameters
default settings 28
system performance 70
system reboot 72
system settings
Current BER field 70
Errored Seconds (ES) field 71
grounding 106
Maximum RSL 71