User's Manual
Table Of Contents
- EX-i Series GigE (FDD)
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- Telnet into the Command Line Interface (CLI)
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- NTP and Time Zone Configurations
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- System Configuration Page
- Allocation Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
- MHS Configuration Page
- VLAN Configuration Page
- Ethernet Rate Limiting Page
- Ethernet Learning Page
- Syslog Configuration Page
- Ethernet Aggregation
- Cross Connect (X Connect) Page
- Alarms Page
- MHS Status Page
- Performance Page
- ATPC Statistics Page
- Event Log Page
- User Throughput Page
- Diagnostic Charts Page
- Ethernet Utilization Page
- PA Control Page
- Spectrum Analyzer
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- EIRP Limits for the United States and Canada
- Licensing 6 and 11GHz Models
- Antennas 5GHz Models
- Copyright Notices
- END USER AGREEMENT
- Index
Exalt Installation and Management Guide
EX-i Series GigE (FDD) Digital Microwave Radios
92 202675-008
2016-06-01
Interfaces
RF
T1/E1 (up to x16)
DS3 (In and Out – up to 4 pairs)
OC3
Ethernet (copper)
Ethernet (SFP)
Connector SMA-type female
Impedance 50 Ohms
Connector RJ-45 (RJ48C), female
T1 Impedance 100 Ohms, balanced
T1 Line Codes AMI, B8ZS, selectable
T1 LBO Settings (in ft.) 0–133, 133–266, 266–399, 399–533, 533–655
T1 Clocking Speed 1.544 Mbps
T1 Compliance ANSI T1.102-1987; ITU-T; G.823; GR-49T-CORE
E1 Impedance 120 Ohms, balanced
E1 Line Codes HDB3
E1 Clocking Speed 2.048 Mbps
E1 Compliance CEPT-1; G.703; ITU-T-G703
Connector BNC, female (x2, In/Out)
DS3 Impedance 75 Ohms, unbalanced
DS3 Line Code B3ZS
DS3 LBO Settings (in ft.) 0–133, 133–266, 266–399, 399–533, 533–655
DS3 Clocking Speed 44.736 Mbps
DS3 Compliance ANSI T1.102-1993; GR-499-CORE
Connector SFP, Single-mode LC Transceiver
Line Code Binary Scrambled NRZ CMI
Clocking Speed 155.52MHz
Compliance ITU-T G.957; G.703 GR-253-CORE
RxTx 1310 nm (Short Range 15km) Rx: –31 to -7dBm, Tx: –15 to 0dBm
1310 nm (Long Range 40km) Rx: –35 to 0dBm, Tx: –5 to 0dBm
Connectors RJ-45, female, auto-MDIX
Interface Speed 10, 100, or 1000 Mbps
Duplex Half, full, auto, selectable
Compliance 802.3
Connectors SFP
Interface Speed 1000 Mbps