User’s Guide for Motorized Pool Lounger Model No. PR10 www.ExcaliburElectronics.
C ongratulations on your purchase of the Motorized Pool Lounger from Excalibur Electronics, Inc. You and your friends will enjoy hours of outdoor fun with this innovative product. Your Motorized Pool Lounger contains two propellers which enable you to turn in all directions. Your Motorized Pool Lounger is easy to use, but be sure to use it safely. Before starting, please read this manual thoroughly, especially noting the safety and care. Keep this manual for reference.
What’s Included Figure 6 Control Arm Figure 7: Electrical Connection Shaft Figure 1: Motorized Pool Lounger Figure 8: Motor Subassembly that Encloses the Propeller Figure 2: Nuts, Bolts, Washers O-Rings and Restoration Kit Figure 3: Battery Compartment Figure 10: Lug Nut Figure 4: Battery Cover & Handle Figure 9: Electric Air Pump with Nozzle Attachments Figure 5: Control Arm Sleeve 4 Figure 11: User’s Guide 5 Figure 12: Instructional DVD
How to Use Setting up the Motorized Pool Lounger in Figure 13. Be sure to read the instructions for the electric air pump on page 20. Insert the medium-size Your Motorized Pool Lounger requires some valve into the electric air assembly. Please carefully pump, as shown in Figure follow these instructions. In 14. addition, Excalibur has included an instructional DVD to help you assemble your Motorized Pool Lounger.
Assembly Next, assemble the battery cover with the nuts, bolts, and oOnce the lounger has been rings in place, as shown in inflated, repeat the following Figure 21. steps on both sides of your Motorized Pool Lounger. Be sure to assemble it on a raised surface to prevent the motor assembly from being damaged. First, take out the wrench provided in the accessories kit as shown in Figure 19. Figure 21 Place the nut onto the bolt and place them onto the battery compartment hole, as shown in Figure 22.
Figure 28 Figure 30 Carefully align the battery Insert the electrical connection compartment cover by matching shaft into the motor subassemthe “3” printed on both the cover bly that encloses the propeller, as and the battery compartment, as shown in Figure 31. shown in Figure 29. Figure 29 Figure 31 Next, hold the lounger vertiFasten the nuts with the cally as shown in Figure 32. This wrench provided in the acces- will make it easier to assemble. sories kit.
Testing the Motorized Pool Lounger Figure 36 After completing all of the previous assembly steps, press the button on the handle to test the propeller, as shown in Figure 38. Repeat the same steps on the other side of your Motorized Pool Lounger, as shown in Figure 37.
Remove the batteries, as partment. Lift it off. shown in Figure 41. On the underside of the Motorized Pool Lounger, squeeze the holes on the base of the control arm sleeve, as shown in Figure 43. This will release the fasteners holding the control arm in place. Figure 41 Unscrew the hexagon nut on the top of the control sleeve, as shown in Figure 42. Figure 43 Figure 42 Once released, lift the control arm from the top of the control arm sleeve.
Apply the glue on the damaged area and apply the supplementary PVC sheet. Wait approximately one minute for the glue to dry after applying the PVC sheet before handling your Motorized Pool Lounger. You should wait approximately 24 hours before using the Motorized Pool Figure 46 Lounger in your pool again. Warning • Please read the User's Guide carefully before operating the product. • Children under 14 years of age should not operate this product without parental supervision.
Special Care & Handling Battery Information • Avoid rough handling such as bumping or dropping. • Your Motorized Pool Lounger uses six D batteries, not included. • Clean using only a slightly damp cloth. Do not use cleaners with chemical agents. • Do not mix old and new batteries. • Avoid extreme temperatures. For best results use between the temperatures of 39° F and 120° F (4° C and 38° C). • Do not mix alkaline, standard (carbon-zinc) or rechargeable nickel-cadmium) batteries.
How to Use the Electric Air Pump The electric air pump is a high-volume, low-pressure pump, as shown in Figure 47. This is intended to inflate or deflate items, such as your Motorized Pool Lounger and air mattresses. To use your electric air Figure 47 pump, please follow these instructions. able item and switch ON to begin inflation. To Inflate While inflating, be sure not to obstruct the valve. Turn the ON/OFF switch to This may cause the pump to OFF. overheat.
Warning for Electric Air Pump • This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, consult an appliance repair-person. Do not attempt to force the plug into the wall outlet. • To reduce the risk of electric shock, do not use if the power cord appears damaged. • Never over-inflate an item.
EXCALIBUR ELECTRONICS, INC. 13755 SW 119TH AVENUE, MIAMI, FLORIDA 33186 U.S.A. Phone: 305.477.8080 Fax: 305.477.9616 PR10 (MA) Motorized Pool Lounger 020306-V5 Play games live at: www.ExcaliburElectronics.